1
NAME OF PARTS
7
%
$
#
@
!*
1
(
)
2
3
4
5
8
6
^
&
! Wash Timer
@ Select Switch
# Water Inlet Port
$ Washer Lid
% Washer Tub
Accessories
7 Spin Mat
^ Strainer
& Pulsator
* Valve Selector
( Spin Dryer Timer
) Spin Dryer Lid
8 Drain Hose Assembly
1 Inner Lid
2 Overflow Filter
3 Spin Dryer Drum
4 Base Under
5 Power Cord
6 Leg (4EA)
2
INSTALLATION
Electrical Connection
• This unit is designed to operate from an adequate supply mentioned at the
rating label sticked to the rear of it.
• In case of 3-core cord: The power cord plug must be connected to an earthed
3-pin power point within reach of the power cord.
• In case of 2 conductor power cord: Connect the grounding wire to a water fau-
cet etc. Make sure that the power cord is unplugged during ground work.
• Do not connect the grounding wire end to a gas tube.
• If the power cord is damaged, it should be replaced by a repair shop appointed
by the manufacturer, because special purpose tools are required.
Connection of Hose
• Attach the water intake hose to the
Water inlet located at the left-hand
side of the con-trol panel. Press fit the
other end of the hose to either a hot
or cold water tap as required. (Fig. 1).
• Attach the drain hose to the drain out-
let at the rear of the base and secure
with the clamp provided.
• The drain hose should be laid flat on the ground. Water flow will be restricted
if any portion of the drain hose is raised 20 cm (8 in) from the ground.
• The opening must not be obstructed by carpeting when the washing machine
is installed on a carpeted floor.
WATER INTAKE HOSE
WATER INLET
Figura 1.
Caution: This unit is made of poly
propylene, use water below 50°C.
HOW TO OPERATE
1. Wash
§Insert the power plug into a wall
socket.
§Set the selector at WASH AND
RINSE, and fill up the washer with
enough water for the washing load.
§Put in the proper amount of detergent.
Pre-washing takes about 2 minutes and is immediately followed by the main
washing process.
Delicate fabric such as silk, wool do not need prewashing.
Divide colored and white clothing into seperate batches.
§Depress one of the select switches
for SOFT or NORMAL washing.
§Turn the washer timer to clockwise until you reach the desired wash time
position. This will activate the pulsator and washing will begin.
Do not attempt to turn the dial from “OFF” to the left, nor past the “15” mark.
3
WASH RINSE
DRAIN
WASH AND
RINSE
NORMAL
BOTH-WAY
SOFT
BOTH-WAY
SELECTOR
SWITCH
Socket Plug
Power cord
After using the machine, unplug the
power cord from the socket.
4
Reference
Water
Washing Fabric Washing Selector level & Detergent
Capacity Time Switch Volume
(Inner clothing)
Silk, Wool, Rayon, Nylon About Soft
Natural/Synthetic fiber 2-4min
blends (Outer garments)
Cotton, Linen (light fabric) About Normal Low 40-50 g
Underwear Pajamas, Shirts 5-7 min 31 L
Heavily solied work About Normal
clothes, Cotton, Linens 8-10 min
(heavy fabric)
Silk, Wool, Nylon, Natural/ About
Synthetic fiber blends 2-4 min Normal
(heavy fabric)
Cotton, Linens About Normal
6-8 min
Heavily Solied About High 55-65 g
Work Clothes 10 min Normal 43 L
Cotton, Linens
Below
1.5 kg
Above
1.5 kg
Item Fabric Unit weight
Sheet Cotton About 400g
Under wear Crape About 130g
Shirts Synthetic fiber About 200g
Sweater Wool About 300g
White shirt Broad About 200g
White shirt Nylon About 160g
Work clothes Cotton About 600g
5
2. Drain
By setting the selector DRAIN, the water
will drain out of the washer. To spin dry
and drain at the same time, first begin
the spin drying process and after one
minute or so start to drain out the water.
3. Spin Dry 1
(1) Spread out the clothes and place
them one at time into the spin
basket.
(2) Close the spin dryer inner cover and
outer cover.
Remember that the machine will not
spin if the cover is opened.
(3) By turning the spin dryer timer to the
desired time, rotation will begin.
(4) If there is any abnormal vibrating
during spin drying, turn off the spin
basket and rearrange the clothes
uniformly inside the dry.
WASH RINSE
VALVE SELECTOR
DRAIN DRAIN
open outer lid open inner lid
5
4
3
2
1
SPIN TIMER
0
stops
NOTE:
It is advisable to wiring out by hand any remaining suds in the cloth-
ing before placing them in the spin basket.
If the spin dry outer lid is opened during spin drying rotation will
automatically stop.
6
CAUTION
Make sure that the spin basket has stopped
rotating before opening the inner cover.
Never reach into spin basket while it is
still in motion.
Be especially careful when children are
present.
4. Rinse
§Return the clothing to the washer tub and set the selector to WASH AND
RINSE.
§Open the faucet and supply water to the washer tub.
Too mush water supplying during rinsing results in overflow and waste. Not
enough water requires an excessive amount of time for through rinsing.
Supply the proper amount of rinse water.
§Adjust the washer timer in accordance with
the clothes to be rinsed.
Once the water becomes clean during the
rinsing process, shut off the faucet and turn
the washer time back to “0”.
5. Spin Dry 2
§After rinsing, spin dry the clothes again.
§Supply water to the dryer to make sure that is completely free of any remain-
ing detergent before putting in the clothes.
Then follow the same process as in SPIN DRY.
After the dryer comes to a complete stop remove the clothing.
15
12
9
6
3
WASH TIMER
0
NOTE:
It is better to put small articles of clothing first such as socks and underwear
into the spin basket, then put bulky and heavy clothing on top.
Clothing Spin dryer time
Clothing that wrinkless easily
Light fabrics such as synthetics fibers, delicate About 1 minute
material.
Clothing that does not wrinkless easily Workclothes, 3-5 minutes
Sheets, Underwear, thick fabric
7
USEFUL INFORMATION FOR YOU
WASHING MACHINE
To ensure longer service from your washer, be sure to observe the
following instructions.
§Never operate the washer until the water has risen to a pre-set level.
§Never pour boiling water directly into the washer tub.
§The color of the plastic portions of the machine is liable to fade and may even
be deformed through exposure to direct sunlight.
§The drain hose should be laid flat on
the ground. Water flow will be res-
tricted if any portion of the drain
hose is raised more than 20cm (8 in)
from the ground.
§Do not use the washer in a damp place such as a bathroom.
§Keep the spin tub cover closed during operation. If the cover is opened the
spin basket will stop rotating.
§Do not splash water on the control
panel.
§For good air ventilation, install the washer at least 5 cm from the wall.
§Be sure to use the proper electrical outlet.
§The overflow filter will need occasional cleaning.
Grasp it at the upper and pull out to remove it. Then, after cleaning out thread
and other matter, replace the filter inserting, its bottom section and then pushing
the upper part firmly into place.
Below
20 cm
8
Dirt may also collect underneath the pulsator.
Clean out occasionally by:
§Remove the screw located in the center of the pulsator.
§Hook the pulsator and pull upwards.
§Wiping clean the bottom of the
washer tub.
(When replacing the pulsator, make
sure that screw is firmly tightened)
When opening and closing the inner lid, make sure to pull it toward you.
CAUTION: For your safety, do not put your hands into spin basket until it
has stopped spinning completely.
IN CASE OF TROUBLE
Please check the following. Unplug the power cord from the socket
before checking.
1. If the washer will not start:
§Check whether the house circuit breaker is tripped or a fuse is blown.
Check whether the power cord is connected to the socket properly.
Check whether something is preventing the pulsator from rotation.
Check whether the belt is attached properly.
(Check by removing rear cover0
2. If there is excessive noise:
§Check whether something is touching the pulsator as rotates.
Check whether the machine is placed level on the floor.
Check whether there is an excessively unbalanced load in the spin basket while
spinning.
9
CAUTION: After installing, DO NOT REMOVE LEGS.
HOW TO FIX LEG TO BASE-HOLE FOR
INSTALLATION
• When you install this unit, be sure to
assemble LEGS(4EA) to base
under(Fig.4).
• Place this unit on its rear side on a
carton to prevent damage to the body.
• Insert the leg(4EA) into the base
under hole as it was. By first inserting
its two hooks.
• Turn right and screw on leg.
• Make the allows of leg and base
under face with each other at each
corner.
HOOK (2EA)
1. Inserting
2. Turn right
3. Screw on.
Figure 4.
WASHER-SPINDRYER
INSTRUCTION MANUAL
Model No.: DW-3610
§Thank you for selecting this washer-spindryer.
§Before operating this unit, please read these instructions completely.
=
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
