Dentsply Sirona Installation Cavitron Built-In A-dec 500 Delivery Systems Operating instructions

Brand: Dentsply Sirona

Model: Installation Cavitron Built-In A-dec 500 Delivery Systems

Type: Operating instructions

Cavitron® Built-In

Ultrasonic Scaling System

For A-dec

Model: G139

Installation Instructions for

A-dec 500® Delivery Systems

2 3

Section 1: Safety Precautions

Safety Precautions

Dentsply Sirona and the distributor of this

product accept no liability for direct or

consequential injury or damage resulting from

improper installation, operation, maintenance

and by not following the Directions for Use.

The Dentsply Sirona Cavitron® Built-In

Ultrasonic Scaling System for A-dec is classiﬁed

by Underwriters Laboratories Inc. with respect

to electric shock, ﬁre and mechanical hazards

in accordance with UL 60601-1.

Danger – This system is not intended for

operation in the presence of ﬂammable

anesthetic or gases.

Danger – Failure to observe the installation

instructions and improper operation may result

in serious patient or user injury. The product

could be damaged, possibly beyond repair.

Before using the product, make sure that

you read and fully understand the operating

instructions.

Caution – Always check the safety status of the

product after repairs. The product must always

comply with the appropriate safety standard

after being repaired.

Caution – This product must only be connected

to a medical grade power supply. If this

product is not connected to the medical grade

power supply, the patient or user may get

an electric shock. In addition, the safety and

correct function of this product cannot be

guaranteed.

Section 2: Installation Overview, Components

and Recommended Tools

Installation Overview

The basic overview of the installation is as

follows:

1. The handpiece cable can be installed into a

Traditional style, Continental® style or A-dec

541 Rear delivery system.

2. Cavitron® Built-In Ultrasonic Scaling System

for A-dec is installed in the A-dec control

head.

3. If the A-dec delivery system has a deluxe

touchpad, connect the Cavitron® Built-In

Ultrasonic Scaling System for A-dec to the

deluxe touchpad inputs.

4. If the A-dec delivery system does not have a

deluxe touchpad, install the optional Cavitron®

Built-In Potentiometer Installation for A-dec in

the control head.

5. Verify installation.

Components

1. Cavitron Built-In Ultrasonic Scaler

2. Steri-Mate Sterilizable Handpiece

3. Handpiece Cable Assembly

4. Control Interface Harness with Air-Electric

Switch

5. Water Regulator Harness Assembly

6. Open/Closed Bushing

7. Quick Disconnect Plug

8. Cable Ties – 4 Large

9. Cable Ties – 4 Small

10. Screw - #4 x 3/8 Long

11. Dual Lock Fasteners

Recommended Tools

1. #1 Phillips Screwdriver

2. #2 Phillips Screwdriver

3. Standard Screwdriver

4. Needle Nose Pliers

5. Wire Cutters

6. Wire Strippers

7. Hex Key Set 7/16 for Continental Cover

Table of Contents

Section 1 Safety Precautions 3

Section 2 Installation Overview, Components and Recommended Tools 3

Section 3 Scaler Installation Preparation 4

Section 4 Continental® Control Head Handpiece Cable Installation 5

Section 5 Traditional Control Head Handpiece Cable Installation 6

Section 6 A-dec 541 Rear Delivery Handpiece Cable Installation 7

Section 7 Cavitron® Built-In Ultrasonic Scaling System for A-dec Installation 8-9

Section 8 A-dec 541 Rear Delivery - Cavitron Built-In Scaler Installation 10-11

Section 9 Main PC Board Installation for A-dec 500 Delivery Systems 12-14

Section 10 Cavitron® Built-In Ultrasonic Scaler Potentiometer Installation for A-dec

500 Delivery Systems 15

Section 11 Cavitron® Built-In Ultrasonic Scaler Potentiometer Installation for A-dec

541 Delivery Systems 16

Section 12 Installation Verification 17

Section 13 Troubleshooting Icons 18

Section 14 Scaler with Deluxe Touchpad Schematic 19

Section 15 Scaler with Potentiometer Schematic 20

Section 16 Installation Parts Kit 21

Section 17 Specifications 22

4 5

Section 3: Scaler Installation Preparation

STEP 1

Turn o the system’s power, air and water.

DANGER: Turn o the power to the system

before you begin this procedure. Failure to do

so can result in electrical shock.

WARNING: Turn o the power to the system

before you begin this procedure. Failure to do

so may result in product damage, serious injury

and/or death.

STEP 2

To open the delivery system cover, lift up on

the center tab on the back of the delivery

system cover. Lift up the tabs on both sides of

the delivery system cover. To remove the cover,

pinch the hinge brackets at the cover base.

CAUTION: When removing or replacing covers,

take care not to damage any wiring. Verify that

the covers are secure after replacing them.

STEP 3

Verify there is space for the scaler inside the

control head. If space is limited, relocate other

ancillary devices. Place the scaler in the left-

rear corner of the control head, leaving about

1/2” to the left and about 1/2” to the rear of the

control head. The harness connector may face

to the right or forward.

WARNING: Do not mount the scaler outside of

the dental control head, doing so will void the

warranty.

Section 4: Continental® Control Head

Handpiece Tubing Installation

STEP 1

Insert the handpiece tubing into the

designated whip arm.

STEP 2

Adjust the handpiece tubing to match the

drape of theother instrument tubing.

STEP 3

Use a small cable tie to fasten the handpiece

tubing at the base of the whip arm pivot.

STEP 4

Route the handpiece tubing wires under the

control head circuit board.

STEP 5

Use a small cable tie to fasten the handpiece

tubing to the control head platform.

STEP 6

Use a large cable tie to attach the handpiece

tubing to the control head platform.

STEP 7

Secure the handpiece tubing strain relief string

with the screw from the installation kit to the

control head platform.

STEP 4

Verify the A-dec control head cover closes. If it

does not close, reposition the Cavitron scaler.

CAUTION: When removing or replacing covers,

take care not to damage any wiring. Verify that

the covers are secure after replacing them.

STEP 5

Conﬁrm there is an empty block position on

the control block.

STEP 6

Verify the empty block is a water block. If not,

replace the dry cartridge with a wet cartridge.

Dry Cartridge Wet Cartridge

6 7

Section 5: Traditional Control Head Handpiece

Tubing Installation

STEP 1

Place the handpiece tubing assembly in the

holder.

STEP 2

Locate an unused opening in the handpiece

tubing guide. Remove the opening cover, if

needed. Route the tubing through the opening.

STEP 5

Secure the handpiece tubing strain relief string

to the control head platform with the screw

from the installation kit.

STEP 7

Secure the handpiece tubing strain relief string

with the screw from the installation kit to the

control head platform.

STEP 5

Route the handpiece tubing through the rear

post of the dental system.

STEP 6

Use a small cable tie to fasten the handpiece

tubing to the other instrument tubing.

STEP 3

Adjust the handpiece tubing to match the

drape of the other instrument tubing.

STEP 4

Use a large cable tie to fasten the handpiece

tubing to the control head platform.

Section 6: A-dec 541 Rear Delivery Handpiece

Tubing Installation

STEP 1

Place the handpiece tubing assembly in the

holder.

STEP 2

Route the handpiece tubing through the

underside of the handpiece tubing guide.

STEP 3

Adjust the handpiece tubing to match the

drape of the other instrument tubing.

STEP 4

Use a large cable tie to fasten the handpiece

tubing to the tubing guide.

8 9

Section 7: Cavitron® Built-In Ultrasonic Scaler

for A-dec Installation

STEP 1

Place the scaler in the leftrear corner of the

control head, leaving about 1/2” to the left

and about 1/2” to the rear of the control head.

Adapter Harness may face right or forward.

STEP 2

Verify the A-dec control head cover closes. If it

does not close, reposition the Cavitron scaler.

CAUTION: When removing or replacing covers,

take care not to damage any wiring. Verify that

the covers are secure after replacing them.

WARNING: Do not mount the scaler outside of

the dental control head, doing so will void the

warranty.

STEP 3

Mount the scaler by peeling o the adhesive

strips on the dual lock fasteners provided and

secure the scaler. Screws may also be used.

STEP 4

Connect the Adapter Harness to the Scaler.

Then connect the Control Harness and

Handpiece connectors.

STEP 7

Connect the clear handpiece water tube to the

”OUT” ﬁtting on the water regulator.

STEP 13

Proceed to Section 9 Main PC Board

Installation for A-dec 500 Delivery Systems

STEP 8

Connect the air electric switch QD adaptor to

the ”DA” drive air port of the control block.

STEP 9

Insert a QD plug (from the installation kit) into

”AC” air coolant port of the control block.

STEP 10

Close the slide lock to secure the QD plugs.

STEP 11

Connect the blue wire with white stripe to the

terminal block containing the grey wires to

24 VAC.

STEP 12

Connect the blue wire to the terminal block

containing black wires to 0 VAC.

STEP 5

Open the slide lock on the control block.

STEP 6

Connect the clear water tubing QD adaptor to

the ”WC” water port of the control block.

Adapter Harness

to Scaler To Handpiece

To Control Harness

10 11

Section 8: A-dec 541 Rear Delivery -

Cavitron® Built-In Ultrasonic Scaler for A-dec

Installation

STEP 1

The scaler should be mounted on the platform,

on the side containing the A-dec control head

circuit board. The Adaptor Harness should be

placed on the right.

STEP 2

The dual lock fasteners may be used to fasten

the scaler. Peel o the adhesive strips on the

dual lock fasteners and secure the scaler to the

control platform.

An alternative is to fasten the scaler with

hardware using available slots.

STEP 3

Connect the Adapter Harness to the scaler

unit. Then connect the Control Harness and

Handpiece connectors.

STEP 4

Open the slide lock on the control block.

STEP 5

Connect the clear water tubing QD adaptor

from water regulator input to the ”WC” water

port of the control block.

STEP 6

Connect the clear handpiece water tube to the

”OUT” ﬁtting on the water regulator.

Adapter Harness

to Scaler To Handpiece

To Control Harness

STEP 7

Connect the air electric switch QD adaptor to

the ”DA” drive air port of the control block.

STEP 8

Insert a QD plug (from the installation kit) into

”AC” air coolant port of the control block.

STEP 9

Close the slide lock to secure the QD plugs.

STEP 10

Coil wires and tubing, as neatly as possible and

use a cable tie to secure it to the panel or to

the gray umbilical hoses. Ensure the tubes are

not kinked or crimped.

STEP 11

Connect the blue wire with white stripe to the

terminal block containing the grey wires to

24 VAC.

STEP 12

Connect the blue wire to the terminal block

containing black wires to 0 VAC.

12 13

Section 9: Main PC Board Installation for

A-dec 500 Delivery Systems

Connect to the Main PC Board

STEP 1

Connect the black wire to the 0 VDC terminal.

CAUTION: Circuit boards are sensitive to

static electricity. Electrostatic Discharge (ESD)

precautions are required when touching a

circuit board or making connections to or

from the circuit board. Circuit boards should

be installed only by an electrician or qualiﬁed

service person.

STEP 2

Connect the yellow wire to the 5 VDC terminal.

CAUTION: Circuit boards are sensitive to

static electricity. Electrostatic Discharge (ESD)

precautions are required when touching a

circuit board or making connections to or

from the circuit board. Circuit boards should

be installed only by an electrician or qualiﬁed

service person.

Conﬁgure the Ultrasonic Instrument Holder

Position

STEP 1

Press and hold the Program and A/B button at

the same time for 3 seconds.

STEP 2

Follow the instructions on the screen to

conﬁgure holder position as an ultrasonic

instrument.

STEP 3

Select HANDPIECES.

STEP 5

For Acteon Colors, Select OFF.

STEP 6

Select SAVE.

STEP 4

Select ULTRASONIC SETUP.

Note: For older touchpads, select SCALER.

A/B Button

Program Button

Conﬁgure the Deluxe Touchpad Display

STEP 1

Press and hold the Program and A/B button at

the same time for 3 seconds.

STEP 2

Press to select Begin.

Conﬁgure the Deluxe Touchpad Memory

Buttons

The ultrasonic scaler memory buttons are

factory preset to the power levels as indicated

below:

The Cavitron Built-In Ultrasonic Scaling System

for A-dec presets can be reprogrammed to a

desired power setting following these steps:

STEP 1

Select the scaler handpiece by removing it

from the handpiece holder or pulling the whip

forward.

STEP 2

Adjust the scaler power with the plus (+) or

minus (-) buttons on the A-dec Touchpad. The

scaler power level may be set from 5 – 100%.

STEP 3

Verify the water is turned on to ensure cooling

of the handpiece and insert tip.

STEP 4

Program a Memory Button:

Press the Program button. One beep and a

blinking ”P” in the top right corner of the

display indicates you are in the Program mode.

STEP 5

Press the memory button to be programmed

(m1 – m4).

STEP 6

Three (3) beeps conﬁrm the setting.

STEP 7

Repeat Steps 2 - 6 for additional memory

button power levels.

BUTTON NUMBER DESCRIPTION

m1 25%

m2 50%

m3 75%

m4 100%

14 15

Memory Buttons

(+) and (-) Buttons

Section 10: Cavitron Built-In Ultrasonic

Scaler Potentiometer Installation for

A-dec 500 Delivery Systems

(The following steps are required only if

Deluxe Touchpad is not used, instead the

Potentiometer Accessory Kit is installed.)

STEP 1

Open the control head cover. Pull up on the

accessory plate on the left side of the control

head.

STEP 2

Attach and orient the power label to the pre-

drilled accessory plate from the installation kit,

as shown in the picture to the right.

STEP 3

Mount the potentiometer to the accessory

plate with the three potentiometer wire tabs

positioned straight up on the accessory plate

for proper alignment.

STEP 4

Use the washer and nut provided to fasten the

potentiometer to the accessory plate.

STEP 5

Turn the potentiometer shaft fully

counterclockwise. Install the knob with the

pointer directed to the minimum position.

Tighten the 2 set screws with the 1/16” hex key

from the installation kit. Turn knob to verify the

rotation matches the dial markings.

STEP 6

Install the accessory plate in the dental control

head.

16 17

Section 11: Cavitron Built-In Ultrasonic Scaler Potentiometer Installation for

A-dec 541 Delivery Systems

(The following steps are required only if Deluxe Touchpad is not used, instead the Potentiometer

Accessory Kit is installed.)

STEP 1

Mount the potentiometer to the Model 541 bracket with the three potentiometer wire tabs

positioned downward.

STEP 2

Use the 5/8 inch washer, star washer and nut provided to fasten the potentiometer to the

bracket as shown in photo.

STEP 3

Turn the potentiometer shaft fully counterclockwise. Install the knob with the pointer directed to

the minimum position. Tighten the 2 set screws with the 1/16” hex key from the installation kit.

Section 12: Installation Veriﬁcation

STEP 1

Turn on power, air and water to the delivery

system.

STEP 2

Lift the Cavitron Built-In Ultrasonic Scaling

System for A-dec handpiece cable from holder

or pull handpiece cable whip arm forward.

STEP 3

Align the Steri-Mate handpiece and the

handpiece cable connector and plug the

handpiece onto the cable.

STEP 4

Adjust the A-dec 500 control head water ﬂow

control to maximum for the Cavitron Built-In

Ultrasonic Scaling System for A-dec and for a

disc foot control, turn on the foot control water

toggle switch.

STEP 5

Turn the water ﬂow control for the handpiece

position to maximum. Also, turn the handpiece

tubing water ﬂow control to maximum. Activate

the foot control disc or lever for two minutes

to ﬂush out the water system. Then hold the

handpiece vertically to ﬁll handpiece with

water. Release the foot control.

STEP 6

Place a Cavitron Ultrasonic insert into the

handpiece.

STEP 7

Activate the foot control disc or lever and

verify the insert oscillates.

STEP 8

Adjust the scaling power using the deluxe

touchpad or optional potentiometer. Verify the

scaling power changes with the touchpad or

potentiometer settings.

Nut

5/8” Washer

Star Washer

Potentiometer

STEP 9

Verify the water ﬂow is adjustable from zero

to maximum ﬂow using the ﬂow control at the

rear of the handpiece.

STEP 10

Release the foot control and verify no water

leaks.

STEP 11

Verify wires and tubing are not trapped or

kinked.

STEP 12

Reinstall the control head cover.

NOTE: The Cavitron Built-In Ultrasonic Scaling

System for A-dec has been successfully

installed.

88019 Rev. 4 (0419)

Cavitron® Built-In

Ultrasonic Scaling System

*CUSTOMER SUPPLIED PARTS

**NOTES: (FOR DIGITAL CONTROL INPUT CONNECTION)

1. USE DOTTED LINES FOR CONTROL VOLTAGE CONNECTIONS TO

CAVITRON SCALER.

2. DO NOT INSTALL THE POTENTIOMETER TO CAVITRON SCALER.

3. INPUT CONTROLVOLTAGE: 5VDC=MAX HANDPIECE POWER.

4. INPUT CONTROL VOLTAGE: OVDC=MIN HANDPIECE POWER.

18 19

Section 13: Troubleshooting Icons Section 14: Scaler with Deluxe Touchpad Schematic

A-dec Control Block

A-dec Control Head

Circuit Board

Blue wire to 0 VAC

Blue w/white stripe wire

to 24 VAC

A-dec Control Head Circuit Board

Black to 0VDC

Yellow wire to 5 VDC

WATER

REGULATOR

ULTRASONIC ENABLE

AIR ELECTRIC SWITCH

DRIVE AIR

WIRE COLOR/DESCRIPTION

ITEM 2

PIN 1 RED DRIVE

PIN 4 GREEN GROUND

WIRE COLOR/ITEM NUMBER

ITEM 1

PINS WIRE COLOR POTENTIOMETER OR DIGITAL INPUT

PIN 1 BLUE 0 VAC 0 VAC

PIN 2 NC

PIN 3 NC

PIN 4 YELLOW WIPER OF POT CONTROL INPUT

PIN 5 BROWN ENABLE ENABLE

PIN 6 BLUE W/ WHITE STRIPE 24 VAC 24 VAC

PIN 7 NC

PIN 8 VIOLET POWER POT NC

PIN 9 BLACK GROUND GROUND

PIN 10 BLACK GROUND GROUND

PIN 2 PIN 3

PIN 1 PIN 4

Pin 1 (BLUE)

PIN 6 PIN 1

PIN 5

PIN 10

REF

WATER TUBE

RED RED

GREEN GREEN

BLUEBLUE

N/C

YELLOWYELLOW

BLACKBLACK

BLUE W/WHITE STRIPEBLUE W/WHITE STRIPE

VIOLET

BROWNBROWN

Pin 9 (BLACK)

Pin 5 (BROWN)

Pin 10 (BLACK)

Pin 4 (YELLOW)

Pin 6 (BLUE W/WHITE STRIPE)

88019 Rev. 4 (0419)

Cavitron® Built-In

Ultrasonic Scaling System

88019 Rev. 4 (0419)

Cavitron® Built-In

Ultrasonic Scaling System

88019 Rev. 4 (0419)

Cavitron® Built-In

Ultrasonic Scaling System

88019 Rev. 4 (0419)

Cavitron® Built-In

Ultrasonic Scaling System

Power On Icon:

If LED is illuminated, Cavitron Scaler has

power. Verify 24VAC is being applied to

scaler via the Blue wire and Blue wire

with white stripe.

Microprocessor Activity Icon:

LED will blink when the microprocessor is active. If the LED is not blinking and the

Power LED is illuminated, cycle the power o and on.

CAN Bus Activity Icon:

If the G139 is connected to the a-dec CAN Bus the LED will blink when

communication is occurring between the a-dec treatment center and G139 Cavitron

scaler. If the G139 is not connected to the a-dec CAN Bus the LED will not illuminate.

Foot Control Icon:

LED will illuminate when the dental unit

foot control is depressed. If the Cavitron

Air Electric Switch harness is being

used and LED does not illuminate when

foot control is depressed, verify at least

20PSI is being delivered to Air Electric

Switch.

Handpiece Continuity Icon:

Handpiece Continuity Icon will illuminate when dental unit foot control is depressed

and handpiece is attached to the handpiece cable.

If LED does not illuminate check the following:

• Verify Foot Control Icon illuminates when foot control is depressed

• Verify connections are secure between the Steri-Mate, Handpiece Cable, adaptor

harness and unit.

• Check handpiece cable and Handpiece pins for damage or corrosion.

• Unplug adaptor harness from unit and measure the resistance across pin 1 (Red

Wire) and pin 3 (Green Wire) with handpiece connected and verify 0.4 ohms.

88019 Rev. 4 (0419)

Cavitron® Built-In

Ultrasonic Scaling System

*CUSTOMER SUPPLIED PARTS

**NOTES: (FOR DIGITAL CONTROL INPUT CONNECTION)

1. USE DOTTED LINES FOR CONTROL VOLTAGE CONNECTIONS TO

CAVITRON SCALER.

2. DO NOT INSTALL THE POTENTIOMETER TO CAVITRON SCALER.

3. INPUT CONTROLVOLTAGE: 5VDC=MAX HANDPIECE POWER.

4. INPUT CONTROL VOLTAGE: OVDC=MIN HANDPIECE POWER.

DESCRIPTION

QTY.

CAVITRON BUILT-IN ULTRASONIC SCALER

DENTSPLY SIRONA

REORDER NUMBER

P/N 8800701

DECORATED HANDPIECE CABLE

66" GRAY HANDPIECE CABLE

66" SURF HANDPIECE CABLE

82" GRAY HANDPIECE CABLE

82" SURF HANDPIECE CABLE

P/N 8134801

P/N 8134802

P/N 8134803

P/N 8134804

1CONTROL CABLE ASSY WITH

DRIVE AIR

P/N 81361

OUT IN

1REGULATOR/HARNESS ASSEMBLY P/N 81369

1OPEN/CLOSED BUSHING P/N 562056007

1QUICK DISCONNECT PLUG P/N 81358

4CABLE TIE- 7-3/8" LONG -

CABLE TIE- 3-7/8" LONG -

SCREW No. 4 x 3/8L -

1SCALER ADAPTER HARNESS P/N 88014

STERI-MATE HANDPIECE, GRAY

8183003 (3-PACK)

8183001 (1-PACK)

STERI-MATE 360° HANDPIECE

8183203 (3-PACK)

18183201 (1-PACK)

20 21

Section 15: Scaler with Potentiometer Schematic Section 16: Installation Parts Kit

A-dec Control Block

A-dec Control Head

Circuit Board

Blue wire to 0 VAC

Blue w/white stripe wire

to 24 VAC

Power

Potentiometer

WATER

REGULATOR

ULTRASONIC ENABLE

AIR ELECTRIC SWITCH

DRIVE AIR

WIRE COLOR/DESCRIPTION

ITEM 2

PIN 1 RED DRIVE

PIN 4 GREEN GROUND

WIRE COLOR/ITEM NUMBER

ITEM 1

PINS WIRE COLOR POTENTIOMETER OR DIGITAL INPUT

PIN 1 BLUE 0 VAC 0 VAC

PIN 2 NC

PIN 3 NC

PIN 4 YELLOW WIPER OF POT CONTROL INPUT

PIN 5 BROWN ENABLE ENABLE

PIN 6 BLUE W/ WHITE STRIPE 24 VAC 24 VAC

PIN 7 NC

PIN 8 VIOLET POWER POT NC

PIN 9 BLACK GROUND GROUND

PIN 10 BLACK GROUND GROUND

PIN 2 PIN 3

PIN 1 PIN 4

Pin 1 (BLUE)

PIN 6 PIN 1

PIN 5

PIN 10

REF

WATER TUBE

RED RED

GREEN GREEN

BLUEBLUE

N/C

YELLOWYELLOW

BLACK

BLACK BLACK

BLACK

BLUE W/WHITE STRIPE

VIOLETVIOLET

BROWN

Pin 10 (BLACK)

Pin 9 (BLACK)

Pin 5 (BROWN)

Pin 10 (BLACK)

Pin 4 (YELLOW)

Pin 8 (VIOLET)

Pin 6 (BLUE W/WHITE STRIPE)

22 23

Section 17: Speciﬁcations

ELECTRICAL INPUT VOLTAGE:

INPUT CURRENT:

INPUT FREQUENCY:

OUTPUT POWER:

24 VAC ± 10% (SELV)

2.5A

50/60 Hz

30W

POWER CONTROL RANGE RESISTANCE:

VOLTAGE RANGE:

0-5 KΩ (1/4W)

0-5 VDC

OPERATING FREQUENCY 30 KHz

WATER INPUT PRESSURE:

FLOW RATE:

WATER TEMPERATURE:

20 – 40 psi. (138 – 275 kPa)

10-60 ml/min

41°F - 77°F (5°C - 25°C)

AIR Input Pressure: 20 - 100 psi. (138-690 kPa)

WEIGHT 4.5 oz. (128 g)

DIMENSIONS (MAX) HEIGHT(w/cover):

WIDTH:

DEPTH:

1.4in (3.5cm)

3.1in (7.9cm)

2.5in (6.4cm)

Part No. 88022-3 Rev. 5 (1219)

Dentsply DeTrey GmbH

De Trey Strasse 1

Konstanz D-78467

Germany

Manufactured By:

Dentsply Professional

1301 Smile Way

York, PA 17404 USA

www.dentsplysirona.com

Dentsply Sirona Installation Cavitron Built-In A-dec 500 Delivery Systems Operating instructions

Dentsply Sirona Installation Cavitron Built-In A-dec 500 Delivery Systems Operating instructions

Dentsply Sirona Installation Cavitron Built-In A-dec 500 Delivery Systems Operating instructions

Related papers

Other documents