Redback 106070 User manual

Brand: Redback

Model: 106070

Type: User manual

This manual is also suitable for

106071

Redback 106070 is a powerful and versatile pole saw designed for pruning trees and shrubs in the private sector. It features a 40V lithium ion battery that provides ample power for tackling tough tasks, and a lightweight design that makes it easy to maneuver. The pole saw's adjustable shaft allows you to reach high branches without a ladder, and the automatic chain oiler ensures that the chain is properly lubricated for optimal performance. With its safety features like the chain brake and hand guard, the Redback 106070 is a safe and efficient tool for any homeowner's landscaping needs.

This safety alert symbol identies important safety messages in

this manual. Failure to follow this important safety information may

result in serious injury or death.

MODEL # 106071 (106070 Kit)

Operation Manual

Part # 108494 Rev A

40V Lithium Ion Cordless Pole Saw

1100 W 120th Ave, Suite 600

Westminster, CO 80234 • 720-287-5182

For Service or Questions

Call 1-877-487-8275

720-287-5182

www.redbackpowerusa.com

Redback products are distributed by

Table of Contents

Important Safety Information

Intended Use ...........................................................................................4

Personal Protective Equipment ...........................................................4

General Safety ........................................................................................ 5

Safety Icons ............................................................................................6

Overview of Components .........................................................................7

Operation.....................................................................................................8

Checking the chain lubricating oil........................................................9

Tensioning the saw chain .....................................................................9

Adjustments before use ....................................................................... 10

Inserting and removing the battery....................................................10

Switching On/Off ...................................................................................11

Battery state of charge ........................................................................11

Maintenance ............................................................................................13

Changing the saw rail and saw chain ...............................................14

Storage ......................................................................................................15

Warranty & Specifications .................................................. Back Cover

Important Safety Information

WARNING: Read and thoroughly understand all instructions and

safety information before assembling or operating the pole saw.

Failure to do so may cause serious injury or death. Do not allow

anyone to operate this pole saw who has not read this manual.

As with all power equipment, a pole saw can be dangerous if

assembled or used improperly. Do not operate this pole saw if you

have doubts or questions concerning safe operation.

Call our customer service department at 720-287-5182,

1-877-487-8275, or visit www.redbackpowerusa.com if you

have any questions or concerns about the safe operation of this

equipment.

Intended Use

The pole saw has been designed for pruning of trees and shrubs

in private sector exclusively. The pole saw is not designed for

felling of trees. Do not use the pole saw for any purpose other than

for which it was designed. Any other use is unauthorized and may

result in serious injury or death.

Personal Protective Equipment

When operating this pole saw it is essential that you wear safety

gear including goggles or safety glasses, steel-toed shoes and tight

tting gloves (no loose cuffs or draw strings). Always wear ear

plugs or sound deafening headphones to protect against hearing

loss when operating this mower. Always wear sturdy footwear.

Never wear sandals, sneakers or open shoes, and never operate

the pole saw with bare feet. Do not wear loose clothing that might

get caught in moving parts.

WARNING

DANGER

Important Safety Information

General Safety

Failure to follow warnings, cautions, assembly and operation

instructions in the Operation Manual may result in serious injury or

death.

READ THE OPERATION MANUAL BEFORE OPERATION.

• Do not permit children to operate this equipment at any time.

• Do not permit others that have not read and understood the

complete Operation Manual to operate this equipment.

• Keep all people and pets a minimum of 10 feet away from the

work area when operating the pole saw.

• Always operate the pole saw with both hands.

• Do not operate the pole saw when under the inuence of alcohol,

drugs or medication.

• Do not allow a person who is tired, otherwise impaired or not

completely alert to operate the pole saw.

• Do not operate the pole saw in rain or other wet conditions. Protect

the pole saw from rain.

• Always keep hands, feet, hair and loose clothing away from the

pole saw.

• The battery should be removed before any repairs are attempted.

Battery tool use and care

• Recharge only with the charger specied by the manufacturer. A

charger that is suitable for one type of battery pack may create a

risk of re when used with another battery pack.

• Use power tools only with specically designated battery packs.

Use of any other battery packs may create a risk of injury and re.

• When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws or other small

metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals may cause burns or a re.

• Under certain conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

• DO NOT USE BATTERIES WITH DAMAGED CASES. Dispose of

batteries properly. Do not dispose of batteries in household waste.

DANGER

Important Safety Information

Kickback

Kickback occurs when the tip of the guide rail touches an

object or when the saw chain becomes jammed in the cut. If the

rail tip touches an object, this may throw the guide rail upwards

and in the direction of the operator. If the saw chain jams on the

upper edge of the guide rail, the rail may quickly recoil in the

direction of the operator.

Kickback can be prevented by holding the saw rmly with both

hands, ensuring that your thumbs and ngers clasp the handles

on the pole saw. Move your body and arms into a position in

which you can withstand the kickback force. Avoid an abnormal

body posture and do not saw above shoulder height.

Safety Icons

Safety icons are to remind you of important information while

you are operating the unit.

Safety Decals

Safety decals on the pole saw are to remind you of important

information while you are operating the unit. Make sure

all decals are attached and in readable condition. Contact

Redback USA at 1-877-487-8275 for replacement decals.

Use caution when operating this power

equipment.

A pole saw has sharp blades. Use

caution when operating, transporting and

handling.

Wear protective noise deafening

headphones when operating.

Use caution around rotating parts!

Do not touch when operating.

Read and understand the Operation

Manual before operating the pole saw.

A pole saw has sharp blades. Use caution

when operating around other people and

pets.

Wear goggles or other eye protection.

The pole saw can propel wood chips and

dust.

Avoid operating in the rain, protect the

battery and pole saw from wet conditions.

106958

Insertion slot for battery

Handle

Switch interlock

On/Off switch

Shoulder belt

Fastening loop for shoulder belt

Upper shaft

Front handle

Shaft coupling

Lower shaft

Housing w/ ventilation openings

Oil tank w/ oil level indicator

Oil tank cover

Saw rail

Saw chain

Protection hood

Hand wheel

Chain tensioning wheel

Chain cover

Spiked bumper

Battery* EP20 (2.0 Ah), EP40 (4.0 Ah),

EP60 (6.0 Ah)

LED state of charge indicator

Release button for battery

Battery charger*

* Optional. Depending on delivery

Overview of Components

Operation

Switch the unit off and remove the battery if the unit is left

unattended; before checking, cleaning or performing other work

on the unit; or if the unit starts vibrating excessively.

Before initial operation

Unpack the pole saw and accessories and check that no parts are

missing or damaged.

NOTE: The batteries (optional; depending on delivery scope) are

not fully charged on delivery. Prior to initial operation, charge the

batteries fully. See user manual of the battery charger.

Lubricating the chain

The unit may be operated with adequate chain lubricating oil only.

Inadequate lubrication will reduce the service life of the power

tool. Check the amount of oil on the oil level indicator.

Topping up the chain oil

Fill the oil tank only with an environmentally compatible quality

chain and bar lubricant (according to RAL-UZ48).

• Do not use waste oil. Renewed contact with waste oil can cause

skin cancer.

• Waste oil is environmentally harmful.

• Waste oil does not have the necessary lubricating properties and

is unsuitable for chain lubrication.

• An oil other than the one recommended may damage the rail, the

chain and the lubricating system.

• Ensure that dirt does not get into the oil tank.

• Avoid spilling oil. Always wipe up any spilled oil.

WARNING

CAUTION

Operation

• Open the oil tank cover A (see Figure 1). Before opening, clean if

required.

• Carefully pour in the chain lubricating oil until it reaches the upper

mark on the oil level indicator B.

• Close the oil tank cover A.

• Check the chain oil level even during operation and top up with

chain oil if required.

Checking the chain lubrication

• Start the unit (see section “Switching on/off the power tool”.

• Hold running saw chain for some time approx. 15 cm above a

suitable surface. If there is adequate chain lubrication, the oil

which is ejected by the saw chain will form a light trail.

Chain tension

Before performing any work on the pole saw, remove the battery.

The teeth on the saw chain are very sharp! Wear protective gloves

when performing any work on the chain.

NOTE: Check and re-adjust the tension of a new chain after

working for a few minutes. Switch the motor off, remove the battery

and actuate the chain brake.

Checking the chain tension

The saw chain must not sag, but it should be possible to pull it 1/16”

to 1/8”away from the saw rail in the middle of the rail (see Figure 2).

Tensioning the saw chain

• Unscrew the hand wheel anti-clockwise until the saw rail can be

moved by hand 1 (see Figure 3).

• Turn the chain tensioning wheel on anticlockwise to tension the

chain 2.

• Turn the saw chain by hand to check that it runs perfectly. It must

slide freely in the rail.

• Tighten the hand wheel to attach the rail and the cover 3.

WARNING

Figure 1

Figure 2

Figure 3

Operation

Adjustments before using

Before performing any work on the garden

tool, remove the battery.

Assembling and adjusting the shoulder belt

• Open retaining hook and hook onto the fastening eye on the

housing (see Figure 4).

• Adjust the shoulder belt to your height. Adjust the shaft length.

To adapt to the working height the shaft length can be varied up

to 17.7 inches (see Figure 5).

• Loosen the threaded sleeve on the shaft coupling 1.

• Extend the lower shaft until the ideal handle length is reached 2.

• Tighten the threaded sleeve 3.

Inserting/replacing the battery

• Charging the battery as described in the battery charger

operation manual.

• Press the charged battery into the power tool until it clicks into

place (see Figure 6).

• To remove, press the release button 1 and pull out the battery 2.

Protect the battery contacts when the

battery is not being used. Loose metal parts

may short-circuit the contacts.

WARNING

Figure 4

Figure 5

Figure 6

Operation

Switching on/off the power tool

Switching on

Make certain that the saw chain has not yet

been positioned for cutting and is not

touching any other objects.

• Hold the saw rmly with both hands and ensure that there are no

people (particularly children) or animals in the immediate vicinity.

First press and hold the switch interlock 1 (see Figure7).

• Then press the On/Off switch 2.

Switching off

• Release the On/Off switch.

When the On/Off switch is released, the saw

chain continue running briefly.

Battery state of charge

• Press the button on the battery to check the state of charge at

the state of charge indicator LEDs (see Figure 8). The indicator

goes out after 5 seconds. If one of the LEDs ashes, the battery

must be recharged. If none of the LEDs light up after the button is

pressed, the battery is faulty and must be replaced.

Before each use

• Check that all parts of the power tool are present, rmly attached

and undamaged.

• Check that the chain tension is correct.

• Check the chain lubrication.

• Check that there are no leaks.

WARNING

Figure 7

WARNING

Figure 8

Operation

Correct posture

Never work on unstable ground!

Never work while standing on a ladder!

Use only when weather conditions are favourable!

• Stand with both legs rmly on the ground.

• Always hold the power tool with both hands!

• Look over the working area and remove any obstructions.

• Switch the pole saw on before starting the cut.

• Apply a uniform pressure to the unit without excessive force.

After use

Always switch the motor off before you put the power tool down!

When the On/Off switch is released, the saw chain continues

running briefly.

• Stop the engine.

• Wait until all rotating parts have come to a standstill.

• Remove the battery.

• Place sheath on cutting mechanism.

• Leave power tool to cool down.

Basic working technique

• Operate the saw at a maximum angle of 60 degrees (see Figure 9).

• Never cut a branch directly aboutthe head!

• Start at the bottom of the trunk and work upwards.

• To cut thick branches saw in 2 steps:

1. Saw upwards into the branch 1/3 of the branch diameter 1.

2. A little further up the branch saw through the branch from

top to bottom 2.

• Saw longer branches piece by piece.

• When limbing trunks lying at on theground, rst always saw off

the branchespointing upwards. Do not cut throughsupporting

branches until the trunk hasbeen sawn into lengths.

WARNING

Figure 9

WARNING

Maintenance

Before performing any work on the pole saw, remove the

battery. Risk of injury by the sharp cutters!

Wear protective gloves.

The user should perform only the maintenance work described

below. All other work, in particular motor maintenance and

repairs, must be performed by a trained specialist. Improper

work may damage the power tool and result in injuries. Have

power tool inspected once a year at a service center.

Overview of cleaning and maintenance

• After using the power tool clean the unit.

• Tension the saw chain.

• Clean oil guide groove in the saw rail.

• Check saw chain oil level, top up if required.

Cleaning

• Do not use water or liquid detergents.

• Clean the unit with a damp cloth and a soft brush.

• Remove the chain cover, and use a soft brush to remove debris

from the saw rail, saw chain, chain wheel and chain cover.

• Keep the ventilation slits clean and dust free.

Servicing

To tension the saw chain, (see Figure 3) on page 9.

Cleaning oil guide groove in the saw rail

• Remove saw rail.

• Remove dirt from the oil guide groove using a suitable tool. Use

a plastic spatula, not a steel tool!

• Re-attach saw rail.

Regrinding saw chain

Special tools are required to sharpen the saw chain and

guarantee that the blades of the chain are sharpened at the

correct angle and to the correct depth. We recommend

having the saw chain reground by specialist.

DANGER

Maintenance

The teeth on the saw chain are very sharp!

Wear protective gloves when handling the chain.

An incorrectly attached saw chain will cause the power tool

to cut in an uncontrolled manner!

When attaching the chain, observe the running direction!

Changing saw rail and saw chain

Place the pole saw on any suitable at surface.

• Unscrew the hand wheel anti-clockwise until the saw rail can

be moved by hand 1 (see Figure 10).

• Turn the chain tensioning wheel clockwise to push the saw

rail as far as possible onto the chain wheel 2.

• Detach the hand wheel 3 and remove the chain cover 4 (see

Figure 11).

• Place saw chain around the saw rail starting on the upper

part of the rail. Slide the chain in the slot around the saw rail.

When attaching the chain, ensure that it is in the correct

running direction.

• Place the saw chain around the chain wheel 5 (see Figure 12).

• Place elongated hole of the saw rail on the stud bolt and the

guide bolt 6.

• Attach the chain guard 7 (see Figure 13).

• Tighten the hand wheel slightly 8.

CAUTION

Figure 10

Figure 11

Figure 12

Figure 13

Maintenance

• Tighten the chain tensioning wheel anticlockwise to tension the

chain 9 (see Figure 14). The saw chain must not sag, but it should

be possible to pull it 1/16” - 1/8” off the saw rail in the middle of

the saw rail.

• Tighten the hand wheel to attach the rail and the cover 10.

• Turn the saw chain by hand to check that it runs perfectly. It must

slide freely in the rail.

NOTE: Check and re-adjust the tension of a new chain after

working for a few minutes. Switch the motor off, remove the battery

and apply the chain brake.

Remove the battery from the pole saw before storing. Store

the pole saw in a dry, dust-free and frost-free place ideally in a

temperature range of 50° - 77°F (10-25 °C). Place the sheath over

the cutting mechanism. Store the battery and the unit separately.

The chain rail can be removed for storage.

Charge the battery before storing the unit in winter. For storage

over long time, drain the chain oil from the chain saw.

Keep the unit, in particular its plastic components, away from brake

uids, petrol, petroleum products, penetrating oil, etc. They contain

chemical substances which may damage, attack or destroy the

plastic components of the unit.

Remove the battery from the pole saw when not in use.

Disposal Information

Recycle raw materials instead of disposing as waste.

Battery, accessories and packaging should be recycled in an

environmentally friendly manner. Plastic parts are identied for

recycling according to material type.

Do not use batteries with damaged casing.

Do not attempt to open batteries.

Do not dispose of in fire, water or household waste.

CAUTION

Figure 14

Storage

Model No.

Serial No.

Date of Purchase

Place of Purchase

Warranty & Specications

IMPORTANT NOTICE

We, the manufacturer, reserve the right to change the product and/

or specications in this manual without notication. The manual is for

information usage only and the pictures and drawings depicted herein are

for reference only.

Warranty Repair and Service

Do not return this product to the store for warranty issues or repair. Call

our customer service department at 720-287-5182, 1-877-487-8275, or visit

www.redbackpowerusa.com for the location of the nearest service center.

Record the information below for future reference.

1100 W 120th Ave., Suite 600

Westminster, CO 80234 • 720-287-5182

Redback products are distributed by

For Service or Questions

Call 1-877-487-8275

720-287-5182

www.redbackpowerusa.com

SKU/Part No. 106071 (106070Kit)

Description 40V Lithium Ion Cordless Pole Saw

Rated Voltage 40 Volts DC

Chain Speed 20 feet/second

Length 80 Inches

Oil Tank Volume 2.37 Fluid Ounces (70mL)

Shipping Weight 7 Lbs. (w/o battery)

Battery 2.0Ah (included with kit)

Battery Charger 2A Charger (included with kit)

Run Time Up to 50 minutes/charge (with 4.0Ah battery)

Warranty 3-Year Limited Warranty; 1-Year on Battery

Redback 106070 User manual

Brand: Redback

Model: 106070

Type: User manual

This manual is also suitable for

106071

Download PDF

report

Redback 106070 User manual

This manual is also suitable for

Redback 106070 User manual

Related papers

Other documents