Entry Door Jamb
Entry Door
Stucco 1 (Top View)
Stucco
Pop-Out
1" minimum
mounting
surface
1" minimum
mounting
surface
StudStud
Rough Opening
Width
Entry Door Jamb
Brick molding trim
Entry Door
Brick Molding (Top View)
StudStud
1" minimum
mounting
surface
1" minimum
mounting
surface
Inspect Your Entryway for
Obstructions
Check for any obstructions above
and around your entryway that
may prevent the outward swing of
your new security door, and/or its
installation, such as:
• Light xtures
• Door bell
• Low overhang
• Door handle of existing entry door
• Trees, bushes, or hanging plants
Determine Mounting Method
and Rough Opening Width
Measure Points
The security door will require a
minimum mounting surface of 1" on
the trim above and on both sides of
the entry door (1" depth also required
for recessed mount). Mounting screws
must be secured to a stud in the wall.
Review Figures 1-5 to determine
which mounting method you can and
wish to use and the rough opening
measurement.
Figure 1 Brick Molding - Surface Mount
Entry Door Jamb
Entry Door
Sloped Trim (Top View)
*Sloped trim must be replaced with at trim
to properly mount your new security door
Once trim is replaced, refer to
Figure 4 for measurement locations
Sloped Trim*
Stud
Stud
Figure 5 Sloped Trim
Entry Door Jamb
Entry Door
Stucco 2 (Top View)
Stucco
Pop-Out
1" minimum
mounting
surface
1" minimum
mounting
surface
StudStud
Figure 3
Stucco 2
– Mounted to front surface of stucco pop-outs -
Surface Mount
Rough Opening
Width
Entry Door Jamb
1" minimum
mounting
surface
1" minimum
mounting
surface
Entry Door
Flat Trim (Top View)
Flat Trim
StudStud
Rough Opening
Width
Figure 4 Flat Trim - Surface Mount
Rough Opening
Width
Figure 4 or 4a for measurement points
MK1286 01242020
Figure 2
Stucco 1
– Mounted between stucco pop-outs
-
Surface Mount
Premium Security Doors
How to
Measure
Rough Opening
Width
Entry Door Jamb
Brick molding trim
Entry Door
Brick Molding (Top View)
StudStud
1" minimum
mounting
surfaces
1" minimum
mounting
surfaces
Figure 1a Brick Molding - Recessed Mount
Rough Opening
Width
Recessed Mount
Surface Mount
Mounting
Screw
Security Door
Security Door
Mounting
Screw
Mounting
Screw
Security Door
Security Door
Mounting
Screw
Recessed Mount
Surface Mount
Mounting
Screw
Security Door
Security Door
Mounting
Screw
Mounting
Screw
Security Door
Security Door
Mounting
Screw
Typical Surface Mount
The security door will be mounted
on top of the existing trim.
Typical Recessed Mount
The security door will be mounted on
the inside of the existing trim.
1
2
Measure for Rough Opening Height
Measure from the bottom edge of the mounting surface to
the existing threshold of your entry door and enter on the
measurement worksheet on the following page.
Y
Check Handle Height
Standard security door handle height is 39-1/2". To check for
potential interference with your main entry door handle, measure
from the threshold to the center of the handle (Y). A measurement
within 38-1/2"-40-1/2" inches may result in interference. To ensure
you avoid interference issues in this instance, you may:
• Mount your security door with an opposite swing
• Order 54" handle height
• Build out the trim on your mounting surface to create clearance
Note: Paddle style handles feature a prole less likely to cause
interference than knob style handles… if measurements indicate
you may be close to an interference issue, keep this in mind when
selecting your security door handle set.
Measure for Rough Opening Width
Measure for the rough opening you identified in Step 2 (Figures 1-5). Measure the top,
middle and the bottom of the door opening. The smallest of the three measurements will
be your rough opening width. Enter that measurement on the measurement worksheet and
follow the instructions to determine if a standard size door will fit or to order the correct
custom sized door.
W1
W2
W3
Premium Security Doors
How to
Measure
3
4
5
Premium Security Doors
Measurement
Worksheet
Door Size
* Rough Opening
Width Fit Range
Rough Opening Width
Overall
Width
* Rough Opening
Height Fit Range
Rough Opening Height
Overall
Height
30" x 80"
29-7/8" - 30-3/8" 31-1/2"
80" - 80-1/2" 81-9/16"
32" x 80"
31-7/8" - 32-3/8" 33-1/2"
36" x 80"
35-7/8" - 36-3/8" 37-1/2"
36" x 96" 96" - 96-1/2"
97-9/16"
60" x 80"
59-7/8" - 60-3/8" 61-1/2"
80" - 80-1/2" 81-9/16"
72" x 80"
71-7/8" - 72-3/8" 73-1/2"
Instructions:
Determine which t range your measurements fall within and order that standard size door. If your
measurement does NOT match a standard size door, give the sales associate your rough opening
dimensions to enter in as a custom size.
Door Size
* Rough Opening
Width Fit Range
Rough Opening Width
Overall
Width
* Rough Opening
Height Fit Range
Rough Opening Height
Overall
Height
30" x 80"
29-1/2" - 30-1/2" 32-1/2"
79-3/4" - 81-3/4" 81-9/16"
32" x 80"
31-1/2" - 32-1/2" 34-1/2"
36" x 80"
35-1/2" - 36-1/2" 38-1/2"
36" x 96" 95
-3/4
" - 97-3/4"
97-9/16"
60" x 80"
59-1/2" - 60-1/2" 62-1/2"
79-3/4" - 81-3/4" 81-9/16"
72" x 80"
71-1/2" - 72-1/2" 74-1/2"
SURFACE MOUNT
RECESSED MOUNT
Standard size door
* Wider rough opening measurements within the t range may require shimming or ller wood. For opening measurements
outside these ranges, custom doors provide the best t and installation.
NOTE: If a custom size is needed, to get overall frame dimensions add 1-1/2" to width and 1" to height.
NOTE: If a custom size is needed, to get overall frame dimensions add 2-1/2" to width and 1-1/4" to height.
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Unique Home Designs SPD06400720002 Operating instructions
-
Unique Home Designs 1S2506DL1WHISA Operating instructions
-
Unique Home Designs IDR064096L2078 Operating instructions
-
-
-
-
-
Unique Home Designs 1S2001KL2CCP2A Installation guide
-
-