Cardo Systems G9 Installation guide

Brand: Cardo Systems

Model: G9

Type: Installation guide

This manual is also suitable for

Cardo Systems G9x

The Cardo Systems G9x is a high-quality audio kit that can be used to enhance your riding experience. With its advanced features, the G9x allows you to listen to music, make and receive phone calls, and even use voice commands to control your device.

Some of the key features of the G9x include:

Bluetooth 4.1 connectivity: The G9x uses Bluetooth 4.1 technology to connect to your other Bluetooth-enabled devices, like your phone or MP3 player.
A2DP stereo audio streaming: The G9x supports A2DP stereo audio streaming, so you can listen to your music in high quality.

Cardo Systems G9x

Some of the key features of the G9x include:

Bluetooth 4.1 connectivity: The G9x uses Bluetooth 4.1 technology to connect to your other Bluetooth-enabled devices, like your phone or MP3 player.
A2DP stereo audio streaming: The G9x supports A2DP stereo audio streaming, so you can listen to your music in high quality.

PLACING THE SPEAKERS

For best sound clarity, place the speakers directly opposite and close as

possible to the ears

. Helmets with deep recesses may require padding

to bring the speakers closer for ideal positioning.

➊

Attach Velcro Pads to the helmet’s inner padding .

➋

Cross the long speaker wire over the center of the helmet to

enhance FM radio reception.

Using two speakers inside the helmet may be prohibited in certain

jurisdictions. If this is the case, postion both speakers on one side of the

helmet.

➊

➋

POSITIONING THE HYBRID MICROPHONE

➊

Open the lining between the helmet’s inner padding. Use the Velcro pad to

hold the Hybrid Microphone in place. Attach the Microphone to the Velcro pad.

➋

Adjust the location so that the microphone is located opposite the center of

your mouth.

➊

➋

CHANGING THE MICROPHONE TYPE

REMOVING:

Before changing the microphone, completely remove the Audio Kit and backplate from the helmet.

ATTACHING:

Reattach the backplate to the Audio Kit, before installing it on the helmet and fully tightening the screws.

POSITIONING THE CORDED MICROPHONE

Attach Velcro to inside front of helmet

The Corded Microphone can be used with Full face helmets only (not Modular helmets).

Some helmets with air vents may require the mic to be repositioned if mic audio is aected.

REPLACING THE CORDED MICROPHONE SPONGE

A replacement corded microphone sponge is provided for future use should you need it.

NOTE: The wires to the microphone are delicate. Avoid touching them.

➊

Pinch and pull existing microphone sponge

➋

Carefully remove the existing sponge.

➌

Remove protective backing sheet from replacement sponge

➍

Carefully attach the new sponge to the microphone

➊

➋

➌

➍

FILE NAME: MAN00160 IG G9x EN/JP J_005 7 July 2014 12:40 PM

communication in motion

™

Note:

Size: 450 x 310 mm

Signature: |

ATTACHING AND REMOVING THE UNIT

➊

ATTACHING:

Slide sideways until a clicking sound indicates that it is locked in place.

➋

REMOVING: Press and slide sideways.

➊

➋

OPTION A – USING THE BACK PLATE

➊

Loosen both screws

➋

Push the back plate between the helmet’s outer shell and inner padding

➌

Adjust the clamp’s location so that the microphone is located opposite the center of your

mouth

➍

Tighten the screws

➊

➋

➌

➍

OPTION B – USING THE GLUE PLATE

Glue the Audio Kit to your helmet when the standard Back Plate method cannot be used. Choose which

of the two glue plates is most suitable for your helmet.

While we have no reason to believe that the gluing option might negatively aect

any helmet, Cardo does not assume any responsibility, irrespective of its nature

and circumstances.

The Glue Plate is oered as an option that you may use at your own risk and subject

to renouncement of any future claims.

This can only be done once!

➊

Remove the metal and plastic parts of the Back Plate

➋

Adjust the audio kit’s location so that the microphone is located in front of the center of your

mouth

➌

Use the Alcohol pad to clean the exact spot on the helmet

➍

Peel o protective backing sheet

➎

Press here for 15 seconds

➏

Allow the glue to dry for 24 hours

➐

Fasten both screws tightly

➊

➋

➌

➍

➎

➏

➐

Audio Kit for G9 and G9x

English

Installation Guide

FILE NAME: MAN00160 IG G9x EN/JP J_005 7 July 2014 12:40 PM

communication in motion

™

Note:

Size: 450 x 310 mm

Signature: |

INTRODUCTION

Thank you for purchasing this scala rider Audio Kit accessory. This manual will

help you to attach it to your motorcycle helmet and set up the microphone and

speakers. We wish you a great scala rider experience!

Attach the scala rider Audio Kit to your helmet using the standard Backplate

(Option A) or one of the Glue Plates (Option B).

➋ ➌

➍

➎

➊

➏ ➐

➑

➒

Alcohol

Pad

Alcohol

Pad

➓

⓫

⓬ ⓭

CONTENTS OF BOX

➊

Noise canceling microphone

➋

Hybrid Microphone

➌

Sliding Panel

➍

Two speakers

➎

MP3 Jack and Speaker Jack (back)

➏

Corded Microphone

➐

Replacement Microphone Sponges

➑

Allen Wrench

➒

Pre-moistened Alcohol Pads

➓

Speaker Booster Pads

⓫

Velcro Pads

⓬

Hybrid Mic Clip

⓭

Glue Plates

➊

➋

➌

➍

➎

➏

➐

➑

➒

➓

⓫

⓬

⓭

MAN00160 IG G9X EN/JP J_005



www.cardosystems.com



support@cardosystems.com



1-800-488-0363

+49 89 450 36819

communication in motion

Cardo Systems G9 Installation guide

Brand: Cardo Systems

Model: G9

Type: Installation guide

This manual is also suitable for

Cardo Systems G9x

Some of the key features of the G9x include:

Bluetooth 4.1 connectivity: The G9x uses Bluetooth 4.1 technology to connect to your other Bluetooth-enabled devices, like your phone or MP3 player.
A2DP stereo audio streaming: The G9x supports A2DP stereo audio streaming, so you can listen to your music in high quality.

Download PDF

report