2. Eurotech
  3. ALUDRA
ALUDRA

Eurotech ALUDRA Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Eurotech ALUDRA Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the ALUDRA Development Kit?
    What are the features of the ALUDRA Development Kit?
    What is the ALUDRA single board computer?
    What is the ALUDRA-Breakout board?
    What is the display set?
    What operating systems does the ALUDRA Development Kit support?
    What are the expansion buses on the ALUDRA Development Kit?
    What are the power requirements for the ALUDRA Development Kit?
Issue B – August 2010 – ETH_ALUDRA_DEVKIT_USM
DIGITAL TECHNOLOGIES FOR A BETTER WORLD
www.eurotech.com
USER MANUAL
ALUDRA Development Kit
5.25" Single Board Computer
ALUDRA Development Kit - user manual
2
ETH
_
ALUDRA
_
DEVKIT
_
USM
WARRANTY
For Warranty terms and conditions users should contact their local Eurotech Sales Office.
TRADEMARKS
All trademarks both marked and not marked appearing in this document are the property of their respective owners.
REVISION HISTORY
Issue no. PCB Date Comments
Issue A
Issue B
V1I1
V1I2
11
th
November 2009
2
nd
August 2010
First full release of Manual.
Updated for new ALUDRA and breakout.
© 2010 Eurotech Ltd. All rights reserved.
See Eurotech Worldwide Presence (on the back cover) for full contact details.
Table of contents
3
Table of contents
Important user information............................................................................................................................. 4
Safety notices and warnings .......................................................................................................................... 4
Life support policy .......................................................................................................................................... 5
CE notice........................................................................................................................................................ 5
WEEE............................................................................................................................................................. 5
RoHS.............................................................................................................................................................. 6
Technical assistance...................................................................................................................................... 6
Introduction...................................................................................................................................................... 7
ALUDRA Development Kit features............................................................................................................... 8
ALUDRA......................................................................................................................................................... 8
ALUDRA-Breakout board............................................................................................................................... 9
Display set (LCD variant only) ....................................................................................................................... 9
Software specification................................................................................................................................... 10
Operating system support............................................................................................................................ 10
Drivers.......................................................................................................................................................... 10
BIOS............................................................................................................................................................. 10
Hardware specification ................................................................................................................................. 11
What’s in the Kit ........................................................................................................................................... 11
What else do I need? ................................................................................................................................... 11
Expansion buses.......................................................................................................................................... 12
CompactFlash socket................................................................................................................................... 12
Graphics support.......................................................................................................................................... 13
Audio support ............................................................................................................................................... 13
USB support................................................................................................................................................. 13
Ethernet........................................................................................................................................................ 13
IDE support .................................................................................................................................................. 13
SATA support............................................................................................................................................... 13
PS/2 interface............................................................................................................................................... 13
Serial ports ................................................................................................................................................... 14
Touchscreen controller................................................................................................................................. 14
GPIO ............................................................................................................................................................ 14
Power requirements ..................................................................................................................................... 14
Connectors..................................................................................................................................................... 15
ALUDRA-Breakout board............................................................................................................................. 15
Summary of connectors and jumpers .......................................................................................................... 16
Connectors................................................................................................................................................... 17
Appendix A – Reference information .......................................................................................................... 25
Appendix B – RoHS compliance .................................................................................................................. 26
Eurotech Worldwide Presence..................................................................................................................... 27
ALUDRA Development Kit - user manual
4
ETH
_
ALUDRA
_
DEVKIT
_
USM
Important user information
In order to lower the risk of personal injury, electric shock, fire or equipment damage, users must
observe the following precautions as well as good technical judgment, whenever this product is
installed or used.
All reasonable efforts have been made to ensure the accuracy of this document; however, Eurotech
assumes no liability resulting from any error/omission in this document, or from the use of the
information contained herein.
Eurotech reserves the right to revise this document and to change its contents at any time without
obligation to notify any person of such revision or changes.
Safety notices and warnings
The following general safety precautions must be observed during all phases of operation, service, and
repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere
in this manual violates safety standards of design, manufacture, and intended use of the equipment.
Eurotech assumes no liability for the customer’s failure to comply with these requirements.
The safety precautions listed below represent warnings of certain dangers of which Eurotech is aware
of. You, as the user of the product, should follow these warnings and all other safety precautions
necessary for the safe operation of the equipment in your operating environment.
Installation in cupboards and safes
In the event that the product is placed within a cupboard or safe, together with other heat generating
equipment, ensure proper ventilation.
Do not operate in an explosive atmosphere
Do not operate the equipment in the presence of flammable gases or fumes. Operation of any
electrical equipment in such an environment constitutes a definite safety hazard.
Alerts that can be found throughout this manual
The following alerts are used within this manual and indicate potentially dangerous situations:
Danger, electrical shock hazard:
Information regarding potential electrical shock hazards:
• Personal injury or death could occur. Also damage to the system, connected peripheral devices, or
software could occur if the warnings are not carefully followed.
• Appropriate safety precautions should always be used, these should meet the requirements set out
for the environment that the equipment will be deployed in.
Warning:
Information regarding potential hazards:
• Personal injury or death could occur. Also damage to the system, connected peripheral devices, or
software could occur if the warnings are not carefully followed.
• Appropriate safety precautions should always be used, these should meet the requirements set out
for the environment that the equipment will be deployed in.
Information and/or Notes:
These will highlight important features or instructions that should be observed.
Important user information
5
Use an appropriate power supply
Only start the product with a power supply that conforms to the voltage requirements as displayed on
the voltage label attached to the system. In case of uncertainty about the required power supply,
please contact your local Eurotech Technical Support Team
(see page 6) or the electricity authority.
Use power supplies that are compliant with SELV regulation.
Use certified power cables. The power cable must fit the product, the voltage and the required current.
Position cable with care, Avoid positioning cables in places where they may be trampled on or
compressed by objects placed on it. Take particular care of the plug, power-point and outlet of power
cable.
Avoid overcharging power-points.
Antistatic precautions
To avoid damage caused by ESD (Electro Static Discharge), always use appropriate antistatic
precautions when handing any electronic equipment.
Life support policy
Eurotech products are not authorized for use as critical components in life support devices or systems
without the express written approval of Eurotech.
CE notice
The product described in this manual is marked with the label in accordance with the 1999/5/EC
regulation.
Eurotech shall not be liable for use of its products with equipment (i.e. power supplies, personal
computers, etc.) that are not CE marked.
WEEE
The information below is issued in compliance with the regulations as set out in the 2002/96/EC
directive, subsequently superseded by 2003/108/EC. It refers electrical and electronic equipment and
the waste management of such products.
When disposing of a device, including all of its components, subassemblies and materials that are an
integral part of the product, you should consider the WEEE directive.
The symbol to the right has been attached to the equipment or, if this has not been
possible, on the packaging, instruction literature and/or the guarantee sheet. By using this
symbol, it states that the device has been marketed after August 13th 2005, and implies
that you must separate all of its components when possible, and dispose of them in
accordance with local waste disposal legislations.
Because of the substances present in the equipment, improper use or disposal of the refuse can cause
damage to human health and to the environment.
With reference to WEEE, it is compulsory not dispose of the equipment with normal urban refuse,
arrangements should be instigated for separate collection and disposal.
Contact your local waste collection body for more detailed recycling information.
In case of illicit disposal, sanctions will be levied on transgressors.
ALUDRA Development Kit - user manual
6
ETH
_
ALUDRA
_
DEVKIT
_
USM
RoHS
This device, including all it components, subassemblies and the consumable materials that are an
integral part of the product, has been manufactured in compliance with the European directive
2002/95/EC known as the RoHS directive (Restrictions on the use of certain Hazardous Substances).
This directive targets the reduction of certain hazardous substances previously used in electrical and
electronic equipment (EEE).
Technical assistance
For any technical questions, or if you cannot isolate a problem with your device, or for any enquiry
about repair and returns policies, feel free to contact your local Eurotech Technical Support Team.
See Eurotech Worldwide Presence
(the back cover) for full contact details.
Transportation
When transporting any module or system, for any reason, it should be packed using anti-static material
and placed in a sturdy box with enough packing material to adequately cushion it.
Any product returned to Eurotech that is damaged due to inappropriate packaging will not be covered by the
warranty!
Device labelling
The ALUDRA serial label is affixed to the end panel of the enclosure this contains the Eurotech part
number which in turn contains information on the version and issue of this product the label also
contains a serial number which is unique to each individual ALUDRA.
The labels will also display product conformity marking.
Introduction
7
Introduction
The ALUDRA Development Kit offers a ready-to-run, rapid application development environment which
saves valuable engineering time.
The ALUDRA Development Kit is available in the following variants:
• ALUDRA Standard DevKit, assembled with a 8.4" Flat Panel Display and touchscreen.
• ALUDRA NO-LCD DevKit, assembled with the perspex base only (No display set).
The ALUDRA Development Kit supports the following features:
• PC/104-Plus (PCI bus).
• PC/104 (ISA bus).
• PCI socket.
• Two PCI Express Mini Card sockets.
• Two 10/100 Ethernet.
• 18-bit LVDS (8.4" 800x600 FDP).
• Analogue VGA interface.
• Audio – Line In, Line Out, Mic In.
• Four USB 2.0 ports.
• 2GB SO-DIMM.
• Two RS232 serial ports.
• Touchscreen controller (Eurotech’s TSC1).
• PS/2 mouse and keyboard.
• One CompactFlash (CF) socket.
ALUDRA Development Kit
ALUDRA Development Kit - user manual
8
ETH
_
ALUDRA
_
DEVKIT
_
USM
ALUDRA Development Kit features
ALUDRA
Processor
• Intel ATOM processor (22mm x 22mm BGA): N270, 1.6GHz.
• 533MHz FSB.
• 1.6GHz 512KB L2 cache.
• Thermal design power: 2.5W.
System Chipset
• North Bridge: Intel 945GSE graphics and memory controller (27mm x 27mm BGA),
thermal design power: 6W.
• South Bridge: Intel ICH7-M IO controller hub (31mm x 31mm BGA),
thermal design power: 3.3W.
System memory
• DDR2 SO-DIMM: 2GB (533MHz).
Ethernet
• Two 10/100/1000 BaseT Ethernet ports on RJ45 sockets with LED indication.
Expansion buses
• One PC/104-Plus (32-bit PCI).
• One PC/104 (16-bit ISA).
• One 32-bit PCI socket.
• Two PCI Express Mini Card socket.
• One CompactFlash (CF) socket with ejector located underneath the Ethernet RJ45.
Drive support
• Two Serial ATA and one Parallel ATA interface.
Legacy
• PC beeper.
ALUDRA Development Kit features
9
ALUDRA-Breakout board
Power supply
• +5V operation (Power brick supply input).
System Control
• Reset button.
• Power LED’s.
Serial ports
• Two RS232 ports (COM1 and COM2).
USB
• Four user accessible USB 2.0 ports on USB type A connectors.
Audio
• Mic/Line in/Line out on standard 3.5mm jacks.
Graphics
• Analogue VGA interface.
GPIO
• Four general purpose outputs with LED indication.
• Four general purpose inputs driven externally or set by on-board jumpers with LED indication.
Legacy
• PS/2 keyboard and mouse support.
Display set (LCD variant only)
Flat panel display
• 8.4 inch LVDS 24bit FPD (800 x 600 pixels).
Inverter
• +5V operation FPD inverter.
Touchscreen
• 8.4" 4 wire resistive touchscreen.
Touchscreen controller
• Eurotech TSC1 RS232 touchscreen controller.
ALUDRA Development Kit - user manual
10
ETH
_
ALUDRA
_
DEVKIT
_
USM
Software specification
Operating system support
The ALUDRA is compatible with the following operating systems:
• Microsoft Windows XP and XP Embedded.
• Wind River Linux 3.0.
• Fedora 11.
• Ubuntu 9.04.
Drivers
All system components have drivers available for Windows XP and Linux.
Refer to the relevant software manual for more information.
BIOS
The BIOS provides the standard functions as well as the following features:
• Full legacy IO support.
• ACPI and APM support.
• Boot support for SATA, IDE, NAND Flash and USB.
• PCIe/PCI bridge support.
• PCI/ISA bridge configuration.
Hardware specification
11
Hardware specification
What’s in the Kit
• Perspex base with the ALUDRA and breakout board mounted on it.
• Perspex panel with the 8.4" flat panel display, inverter and TSC1 mounted on it (LCD variant
only).
• All interconnecting cables.
• 5V output power brick supply.
• US, UK or European power cord.
• Eurotech Touchscreen Stylus.
• Eurotech ALUDRA Development Kit DVD.
• 2GB USB memory stick.
• 2 metre Crossover RJ45 UTP cable.
• 2 metre Null-Modem DB9F to DB9F cable.
• Eurotech cleaning cloth.
What else do I need?
• A PS/2 or USB keyboard.
• A PS/2 or USB mouse.
• A VGA monitor (if not using the flat panel kit or for dual display support).
• A development system with DVD-ROM drive.
ALUDRA Development Kit - user manual
12
ETH
_
ALUDRA
_
DEVKIT
_
USM
Expansion buses
PC/104-Plus bus interface
The PC/104-Plus bus interface on the ALUDRA supports PCI local bus compatible peripherals and is
compliant to PCI Local Bus Specification Revision 2.1. This version of the PCI bus is intended as a 32-
bit bus running at 33MHz.
The ALUDRA supports a stack of up to four PC/104-Plus cards.
The +3.3V, +5V and +12V power rails are routed to the PCI connector to provide power to the PC/104-
Plus modules. The ALUDRA power connector is not provided with +12V from the breakout board. If
+12V is required, it is recommended that an ATX power supply is used instead of the power from the
breakout board.
If -5V or -12V is required, they need to be supplied directly to the PC/104 add-on board.
PC/104 bus interface
PC/104 bus interface (www.pc104.org) supports 16-bit ISA compatible peripherals. Standard 64+40
way 0.1" stack-through connectors are used.
The ALUDRA supports a stack of up to four PC/104 cards.
The +5V and +12V power rails are routed to the ISA connectors to provide power to the PC/104
modules. The ALUDRA power connector is not provided with +12V from the breakout board. If +12V is
required, it is recommended that an ATX power supply is used instead of the power from the breakout
board.
If -5V or -12V is required, they need to be supplied directly to the PC/104 add-on board.
PCI Express Mini Card sockets
Two PCI Express Mini Card sockets are available for wireless connectivity. Two of the ICH7-M PCI
Express ports and USB 2.0 ports are connected directly to the PCIe Mini Card sockets on the
ALUDRA.
PCI socket
The PCI socket provided on the ALUDRA supports PCI Local Bus Specification Revision 2.3, 32-bit at
33MHz.
CompactFlash socket
A CompactFlash (CF) socket is provided on the ALUDRA and located under the RJ45 connector. The
CF socket is fitted with an ejector to facilitate removal.
An LED is present on the ALUDRA-Breakout and signals access to a CF card, IDE bus and SATA bus.
Hardware specification
13
Graphics support
The ALUDRA Development Kit supports dual independent pipe for multiple display modes on two
outputs:
• 18-bit LVDS.
• VGA.
The two display outputs can be configured in a number of display modes, to allow for independent
display timings and extended desktop/multi-monitor operating modes.
Audio support
The ALUDRA Development Kit supports stereo line in and out and a mono microphone input on
standard 3.5mm stereo jacks on the ALUDRA breakout board.
USB support
There are four user USB 2.0 high-speed root ports accessible on USB A connectors located on the
ALUDRA-Breakout board. USB 2.0 allows data transfers up to 480MB/s.
Ethernet
Two 10/100/1000 Ethernet RJ45 sockets are available on the ALUDRA board. The Realtek
RTL8111CP Gigabit Ethernet controller supports MDI/MDI-X feature, enabling auto-correction of
incorrect cabling with respect to cross-over versus straight-through cables.
Link and Activity LEDs are built in the RJ45 socket and indicate the link state and transfer activity of
the ALUDRA over the network.
IDE support
The single primary parallel ATA/IDE interface is directly accessible on the ALUDRA board through a
44-pin header (IDE1) on the ALUDRA board. This gives the user the possibility to connect an external
hard drive or CD-drive to the ALUDRA board.
An LED is present on the ALUDRA-Breakout and signals access to a CF card, IDE bus and SATA bus.
SATA support
Two SATA interfaces (SATA1 and SATA2) are directly accessible on the ALUDRA board. Power for
these is provided by two 2-pin headers (CN1 and CN2) This gives the user the possibility to connect
external hard drives or CD drives to the ALUDRA board.
An LED is present on the ALUDRA-Breakout and signals access to a CF card, IDE bus and SATA bus.
PS/2 interface
Legacy PS/2 keyboard and mouse are supported on standard PC MiniDin connectors on the ALUDRA
breakout board.
ALUDRA Development Kit - user manual
14
ETH
_
ALUDRA
_
DEVKIT
_
USM
Serial ports
Serial ports 1 and 2 are full RS-232 interface ports accessible on standard SUBD9 male connectors on
the ALUDRA breakout board.
Serial port 3 is a full RS-232 interface port and is connected to the Eurotech TSC1 by default. (This is
only fitted for the LCD variant only.)
Touchscreen controller
The ALUDRA Development Kit supports the Eurotech’s TSC1. The TSC1 is an analogue resistive
touchscreen controller that interfaces with the processor board via an RS232 serial port.
For more details about the TSC1, please contact the Eurotech sales team (see page Eurotech
Worldwide Presence).
GPIO
Four digital inputs and outputs are provided with +5V and GND on a 2 x 5-way connector with push-in
spring-cage connections on the ALUDRA breakout board.
Input and output levels are indicated by 2 banks of 4 LEDs on the ALUDRA breakout board. The LEDs
are on with a low logic level and off with a high logic level.
The digital inputs logic level can be set without external wiring by fitting the corresponding jumper to
the digital input selection header. If these inputs are controlled by external hardware the jumper must
not be fitted to the header. Fitting a jumper sets the logic level low (LED on).
Power requirements
The ALUDRA Development Kit system operates from a single +5V (+/-5%) power input on a 3.5mm
pitch screw terminal socket.
A suitable +5V power supply is provided in the kit (auto-ranging 90-264VAC input, 5VDC 10A output
switching power supply).
The typical power consumption of the Development Kit system with no extra device/add-on card is less
than 20W.
A removable wired CR2032 coin cell battery is provided for RTC backup on the ALUDRA board.
Connectors
15
Connectors
ALUDRA-Breakout board
The following diagrams show the location of the connectors and jumpers on the ALUDRA-Breakout.
Top view
J9 J8 J6 J1 J2 J3 J4 J5
J11 J15 J10 J7
Front view
S1 (reset) J18 (VGA) J17 (RS232) J19 (Audio) J13 (USBs)
J14 (power) J16 (GPIO) J18 (KB) J18 (MS) J17 (RS232) J12 (USB)
The connectors on the following pages are shown in the same orientation as the pictures above, unless
otherwise stated.
ALUDRA Development Kit - user manual
16
ETH
_
ALUDRA
_
DEVKIT
_
USM
Summary of connectors and jumpers
The following table lists the connectors on the ALUDRA-Breakout:
Connector Function Connector details in section
J1 ALUDRA GPIO GPIO header, page 17
J2
ALUDRA PS/2 mouse and keyboard
and VGA
PS2 mouse, keyboard and VGA header,
page 17
J3 ALUDRA RS232 (1-2) COM1 and COM2 header
, page 18
J4 ALUDRA audio Audio header
, page 18
J5 ALUDRA USB (0-3) USB 2.0 (ports 0 - 3) header
, page 19
J6 ALUDRA front panel Front panel header
, page 19
J7
Development Kit digital input level
selection
Digital input selection header
, page 19
J8 ALUDRA AT power AT power socket
, page 20
J9
Development Kit Touch screen power
output
TSC1 power header
, page 20
J10
Development Kit Off board HDD
activity LED
External HDD activity LED header
, page 20
J11 Backlight inverter power output Backlight inverter power header
, page 21
J12 Development Kit USB (0-1) USB0/USB1 connector
, page 21
J13 Development Kit USB (2-3) USB2/USB3 connector
, page 21
J14 Development Kit +5V DC input +5V DC in screw terminal socket
, page 21
J15 Development Kit off board reset External reset header
, page 22
J16 Development Kit GPIO GPIO connector
, page 22
J17 Development Kit RS232 (1-2) COM1/COM2 connector
, page 22
J18
Development Kit PS/2 mouse and
keyboard and VGA
PS2 mouse, keyboard and VGA multifunction
connector, page 23
J19 Development Kit audio Audio jacks
, page 24
Connectors
17
Connectors
There are 19 connectors on the ALUDRA-Breakout; the use of each one is explained below.
J1 – GPIO header
Connector: FCI Minitek 98464-G61-10ULF, 10-way, 2mm (.0787"), shrouded header.
Mating housing: FCI Minitek 90311-010LF.
Crimps: FCI Minitek 77138-201LF.
Mating receptacle: FCI Minitek 89947-710LF.
Pin Signal name Pin Signal name
1 GND 2 +5V_DIO
3 DOUT3 4 DOUT2
5 DOUT1 6 DOUT0
7 DIN3 8 DIN2
9 DIN1 10 DIN0
J2 – PS2 mouse, keyboard and VGA header
Connector: FCI Minitek 98464-G61-16ULF, 16-way, 2mm (.0787"), shrouded header.
Mating housing: FCI Minitek 90311-016LF.
Crimps: FCI Minitek 77138-201LF.
Mating IDC receptacle: FCI Minitek 89947-718LF.
Pin Signal name Pin Signal name
1 RED 2 DDC_SCL
3 GREEN 4 DDC_SDA
5 BLUE 6 GND
7 HSYNC 8 GND
9 VSYNC 10 GND
11 PS2V5 12 MS_DATA
13 MS_CLK 14 KB_DATA
15 KB_CLK 16 GND
ALUDRA Development Kit - user manual
18
ETH
_
ALUDRA
_
DEVKIT
_
USM
J3 – COM1 and COM2 header
Connector: FCI Minitek 98464-G61-18ULF, 18-way, 2mm (.0787"), shrouded header.
Mating housing: FCI Minitek 90311-018LF.
Crimps: FCI Minitek 77138-201LF.
Mating receptacle: FCI Minitek 89947-718LF.
Pin Signal name Pin Signal name
1 DCD1 2 DSR1
3 RX1 4 RTS1
5 TX1 6 CTS1
7 DTR1 8 RI1
9 GND 10 GND
11 RI2 12 DTR2
13 CTS2 14 TX2
15 RTS2 16 RX2
17 DSR2 18 DCD2
J4 – Audio header
Connector: FCI Minitek 98464-G61-10ULF, 10-way, 2mm (.0787"), shrouded header.
Mating housing: FCI Minitek 90311-010LF.
Crimps: FCI Minitek 77138-201LF.
Mating receptacle: FCI Minitek 89947-710LF.
Pin Signal name Pin Signal name
1 LINE_OUT_R 2 LINE_IN_R
3 GND 4 GND
5 LINE_OUT_L 6 LINE_IN_L
7 GND 8 GND
9 MIC_IN 10 NC
Connectors
19
J5 – USB 2.0 (ports 0 - 3) header
Connector: FCI Minitek 98464-G61-16ULF, 16-way 2mm (.0787") shrouded header.
Mating housing: FCI Minitek 90311-016LF.
Crimps: FCI Minitek 77138-201LF.
Mating receptacle: FCI Minitek 89947-716LF.
Pin Signal name Pin Signal name
1 +V5_USB0-1 2 GND
3 USB_D0- 4 USB_D1+
5 USB_D0+ 6 USB_D1-
7 GND 8 +V5_USB0-1
9 +V5_USB2-3 10 GND
11 USB_D2- 12 USB_D3+
13 USB_D2+ 14 USB_D3-
15 GND 16 +V5_USB2-3
J6 – Front panel header
Connector: Oupiin 2015-2X4GDB/SN, 8-way, 2.54mm (0.1") x 2.54 (0.1") dual row header.
Mating connector: FCI 71600-008LF.
Pin Signal name Pin Signal name
1 PWR_BTN+ 2 PWR_LED+
3 GND 4 GND
5 HDD_LED+ 6 SYS_RST#
7 HDD_LED- 8 GND
J7 – Digital input selection header
Connector: Oupiin 2015-2X4GDB/SN, 8-way, 2.54mm (0.1") x 2.54 (0.1") dual row header.
Mating connector: FCI 71600-008LF.
Pin Signal name Pin Signal name
1 GND 2 DIN3
3 GND 4 DIN2
5 GND 6 DIN1
7 GND 8 DIN0
2 8
1 7
7 1
8 2
ALUDRA Development Kit - user manual
20
ETH
_
ALUDRA
_
DEVKIT
_
USM
J8 – AT power socket
Connector: TYCO 770997-1 power socket.
Mating housing: TYCO 1-480426-0.
Crimps: TYCO 163305-2.
Pin Signal name
1 NC
2 GND
3 GND
4 +5V
J8 provides output power only. Do not connect to an input power source.
J9 – TSC1 power header
Connector: MOLEX KK 0022057028, 2-way, 2.54mm (0.1") header.
Mating housing: MOLEX KK 0022012025.
Crimps: MOLEX 0008500030.
Pin Signal name
1 +5V
2 GND
J10 – External HDD activity LED header
Connector: FCI Dubox 76384-402LF, 2-way, 2.54mm (0.1") header.
Mating housing: FCI Dubox 65240-002LF.
Crimps: FCI 76357-401LF.
Pin Signal name
1 HDD_LED-
2 HDD_LED+
1
2
3
4
1
1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/