VONN Lighting VMW16920AL Operating instructions

Brand
VONN Lighting
Model
VMW16920AL
Type
Operating instructions

VONN Lighting VMW16920AL is an LED lighting fixture that is designed to be installed on a wall or ceiling. It comes with a mounting bracket and screws for easy installation. The fixture has a sleek and modern design with a white finish. It is made of durable materials and is built to last. The fixture is energy-efficient and uses only a fraction of the energy of traditional lighting fixtures. It also has a long lifespan, so you won't have to replace it for many years. The fixture is dimmable, so you can adjust the brightness to suit your needs.

VONN Lighting VMW16920AL is an LED lighting fixture that is designed to be installed on a wall or ceiling. It comes with a mounting bracket and screws for easy installation. The fixture has a sleek and modern design with a white finish. It is made of durable materials and is built to last. The fixture is energy-efficient and uses only a fraction of the energy of traditional lighting fixtures. It also has a long lifespan, so you won't have to replace it for many years. The fixture is dimmable, so you can adjust the brightness to suit your needs.

© VONN Lighting,2017
Installation Guide
ON
VONN Lighting
Model:
VMW16920
Tools You May Need
GOGGLES
TAPE MEASURE
RUBBER
GLOVES
PHILLIPS
LADDER
DRILL
SCREW DRIVER
Circuit Box
Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact VONN Lighting
Customer Service at 888-604-8666 for a replacement.
Please read and comprehend the entire manual before attempting to
assemble, operate, or install the product.
VONN highly recommends to use a qualified, licensed electrician to install
the fixture.
VONN recommends to install the fixture on its own independent circuit.
Do not install the fixture on the same circuit with other appliances, or
HVAC systems.
LED INFO & WARNINGS
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
•
Inspect the LED fixture prior to installation to make sure that it has not
been damaged during shipping.
•
Please handle the LED light with care when unpacking. Do not apply
pressure to the LEDʼs, do not open any factory sealed compartments, and
do not touch the LEDs with your hands.
•
•
Place the wall switch in the “OFF” position of the room you are installing
the fixture.
•
Shut “OFF” the electricity at main fuse box.
•
VONN recommends ELV (Electric Low Voltage) type dimmers for this
fixture.
•
•
Do not remove or replace VONN manufactured driver that is provided
with the fixture.
Parts List
A.
B.
C.
D.
E.
A
B
C
D
E
Mounting Bracket
Outlet Screws x 3
Wire Connectors x 3
Ground Screw x 1
Hexagon Nuts x 3
F. Mounting Bracket Screws x 2
G.Mounting Plate
F
G
x2
GND
•
•
© VONN Lighting,2017
WALL
GND
Hexagon Nut
E
Mounting
Bracket
A
Wire Connector
C
D
Outlet
Screw
B
Ground
Screw
Mounting Bracket Screw
F
Fixture Diagram
Outlet Box
Set Screw
© VONN Lighting,2017
WALL
GND
Mounting
Bracket
A
Outlet
Screw
B
Align mounting bracket (A) with outlet box and
secure with outlet screws (B).
Step 1. Install Mounting Bracket
© VONN Lighting,2017
WALL
GND
Step 2. Connect Wires
Supply Wires:
Ground Wires:
Connect Black (Line Wire) from fixture to Black (Hot Wire)
from outlet box.
Connect White (Neutral Wire) from fixture to White (Neutral
Wire) from outlet box.
Connect Bare Copper (Ground Wire) from fixture to Green
or Bare Copper (Ground Wire) from outlet box.
Twist wires together clockwise and secure with wire
connector (C).
Installer Tip (1): If ground wire is not available in outlet box,
then secure Bare Copper (Ground Wire) from fixture to
ground screw (D) on mounting bracket (A).
Installer Tip (2): Supply wires can be either tucked into
outlet box or fixture canopy.
Mounting
Bracket
A
Ground
Screw
D
White
(Neutral Wire)
Black
(Line Wire)
Bare Copper
(Ground Wire)
Wire Connector
C
© VONN Lighting,2017
WALL
GND
Step 3. Mount Fixture
Mounting
Bracket
A
Mounting Bracket Screw
F
Align mounting plate (G) with mounting bracket
screws (F). Secure with hexagon nuts (E). Attach
fixture to mounting plate (G). Secure with set
screws.
Hexagon Nut
E
Mounting
Plate
G
Set Screw
© VONN Lighting,2017
Step 4. Turn Power ON
Turn electricity “ON” at main fuse box.
Place the recommended ELV type dimmer switch in the “ON” position to test the fixture.
ON
ON
Circuit Box
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

VONN Lighting VMW16920AL Operating instructions

Brand
VONN Lighting
Model
VMW16920AL
Type
Operating instructions

VONN Lighting VMW16920AL is an LED lighting fixture that is designed to be installed on a wall or ceiling. It comes with a mounting bracket and screws for easy installation. The fixture has a sleek and modern design with a white finish. It is made of durable materials and is built to last. The fixture is energy-efficient and uses only a fraction of the energy of traditional lighting fixtures. It also has a long lifespan, so you won't have to replace it for many years. The fixture is dimmable, so you can adjust the brightness to suit your needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents