Hotpoint AS600V (EX) Owner's manual

Contents

TUMBLE DRYER

AS600V

Instruction booklet

Important Information, 2

Installation, 3-4

Where to put your dryer

Ventilation

Electrical connection

Before you start using your dryer

Dryer description, 5

The front

The back

Control panel

Start and programmes, 6-7

Choosing a programme

Table of programmes

Laundry, 8-9

Sorting your laundry

Wash care labels

Special clothing items

Drying times

Warnings and Suggestions, 10

General safety

Disposal

Saving energy and respecting the environment

Maintenance and Care, 11

Switching off the electricity

Cleaning the filter after each cycle

Check the drum after each cycle

Cleaning the dryer

Troubleshooting, 12

Service, 13

Spare parts

GB

English, 1

F

Français, 14

A

Arabic, 40

GB

1

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and

should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the

dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.

! Read these instructions carefully; the following pages contain important information on installation and suggestions

on how the appliance works.

2

GB

Important Information

! You MUST clean the fluff filter after EVERY drying

cycle.

Fluff Filter...

! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.

- It will take longer to dry and as a result will use more electricity during drying.

STEP 1.

Open the door of your

dryer.

STEP 2.

Pull out the filter (using

the two finger grips).

STEP 3.

Clean any fluff deposits

from the filter mesh.

For your Venting dryer to operate efficiently, you must follow the regular maintenance schedule shown below:

STEP 4.

Refit the filter.

- Make sure the arrows

are facing you.

STEP 5.

Make sure the filter is

pushed fully home.

- NEVER run the dryer

without the filter in position.

! You MUST clean fluff build up around the filter housing and the vent tube periodically, EVERY two or three months:

- Check the vent tube and any permanent venting fixture to make sure that there has been no accumulation

of fluff or lint, and remove it.

- Remove lint that collects around the filter and the outlet vents.

GB

3

Installation

Permanent venting

In conjunction with the vent tube we recommend

using a Wall/Window Vent Kit, available at a retail

location or the nearest Spare Parts Dealer.

Wall mounting

1. Leave an opening in

the wall to the left of the

dryers proposed position.

2. Keep the tube as short

and straight as possible

to prevent condensed

moisture from backing up

into the dryer.

3. Similarly, the duct in

the wall should slope

downwards towards the

outside.

Window mounting

1. With a stacked dryer

the hole in the window

should ideally be made

below the vent.

2. The tube should be

kept as short as possible.

Depending on how often you use your dryer, it is

essential that areas A and B are checked periodically

to remove lint or debris.

The vent tube adaptor must be fitted securely thus

preventing any humid air from being emitted back into

the room.

! The Dryer should not be pushed so far back that the

tube adaptor is pulled out of position or the tube is

squashed or bent.

! The tube should be kept clear of the air intake vent

and kinks or ‘U’ bends must be avoided as these will

obstruct the tube or trap condensation.

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the

appliance under a work

counter, be sure to leave a

10mm space between the

top and any other objects on

or above the machine and a

15mm space between the

sides and lateral furnishings

or walls. This is to ensure

proper air circulation. Make sure that the back

vents are not obstructed.

●

Make sure you put your dryer in an environment

that is not damp and has proper air circulation

throughout, the dryer will not operate efficiently in

an enclosed space or cupboard.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

Ventilation

The Dryer dries your laundry by drawing in cool, clean

and relatively dry air, heating it, and then distributing it

through the clothes as they are gently tumbled. For

optimum performance, the moist air is then blown out

through a vent tube at the back of the dryer.

When the dryer is in use, there has to be adequate

ventilation to avoid the back flow of gases into the room

from appliances burning other fuels, including open fires.

Mobile venting

A vent tube must always be fitted when the dryer is

used in conjunction with Mobile Venting.

The tube must be fitted securely into the back of the

dryer (see Dryer Description). If possible, it is always

best to connect the tube to a permanent

outlet close to the dryer. If permanent installation is

not possible, the dryer will work just as well with the

tube passing through a partly-opened window.

! Ensure that the end of the tube is not directed

toward the air intake vent at the rear of the dryer.

! The vent tube should not exceed 2.4 metres in

length and should be kept free of any possible

accumulation of fluff, lint and water by shaking it out

frequently. Always ensure that the tube is not

squashed.

Minimum gap 10mm

Minimum gaps

15mm

4

GB

! Do not use extension cords.

! The power cord must not be bent or squashed.

! The power supply cord should be checked periodically

and replaced by a cord specially prepared for this dryer

and fitted only by authorised technicians (see

Service). New or longer power cords are supplied at

an extra charge by authorised dealers..

! The manufacturer denies any responsibility should

any of these rules not be followed.

! If in doubt about any of the above consult a qualified

electrician.

Levelling your dryer

The dryer must be installed level for correct operation.

When you have installed

your dryer in its final

location check that it is

level first side to side,

then front to back.

If the dryer is not level,

use a wooden block to

support it while adjusting

the two front legs up or

down, until your dryer is

level.

Before you start using your dryer

Once you have installed your dryer and before you

use it, clean the inside of the drum to remove any

dust that could have accumulated during transport.

Open window venting

The end of the tube

should be directed

downwards, to prevent

warm moist air from

condensing in the room or

in the dryer.

! Ensure that the dryer is adequately ventilated and

that the end of the vent tube is not directed towards

the air intake duct.

! The vent tube must always be fitted for optimum

performance.

! Make sure that the vent tube and air intake vents are

not obstructed or blocked.

! The dryer must not recycle exhaust air.

! Misusing a tumble dryer may create a fire hazard.

! Do not discharge exhaust air into a flue which is

used for exhaust fumes from other appliances that

burn gas or other fuels.

! Do not discharge exhaust air into an extraction

system or any duct with an extractor fan. This will

affect the way the thermal controls operate and can

result in a fire hazard.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated

on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers

plug. Should this not be the case, replace the

plug or the socket.

! The dryer must not be installed outdoors, even if the

space is sheltered. It can be very dangerous if it is

exposed to rain or storms.

! Once installed, the dryers electrical wire and plug

must be within easy reach.

Installation

GB

5

Control panel

The front The back

Control Panel

Drum

Air Intake Vent

Model & Serial

numbers

Filter

The Drying Guide allows you to consult a user

friendly table of fabric types and load capacities.

The TIMER knob sets a delay on the dryer’s start

time. Rotate it clockwise until you reach the number of

hours you want to delay the start time: If you have

gone too far, turn the knob counter-clockwise (see

Start and Programmes).

The PROGRAMMES knob sets the programme: rotate

it clockwise, never counter-clockwise, until the

indicator is pointing to the programme you want to

select (see Start and Programmes).

Dryer Description

The START button begins drying a selected

programme (see Start and Programmes).

The HEAT button selects drying temperature (see

Start and Programmes).

OUT: LOW heat

IN: HIGH heat

The ALARM buzzer signals the end of a drying cycle.

IN: Buzzer ON

OUT: Buzzer OFF

The ACTIVE indicator light signals that your dryer

is in use. This light will glow when the START button is

pressed. It will remain on until the door is opened or

the power is turned off. This light will be on during a

delayed start programme.

Vent Tube fitted here

Caution: Hot!

Rating plate

Drying Guide

PROGRAMMES

Knob

TIMER

Knob

START

Button

Indicator

ACTIVE

Light

HEAT

Button

ALARM

Button

6

GB

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door and make sure the filter is clean

and in place (see Maintenance).

4. Load the machine and make sure items are not

in the way of the door seal. Close the door.

5. Choose the drying programme by checking the

Programmes table (see Programmes) as well as

the indications for each type of fabric (see

Laundry).

- Set the temperature with the HEAT button.

- Select a programme or drying time by rotating

the PROGRAMMES knob clockwise.

6. Set a delay time by using the TIMER knob if

necessary.

7. If you wish to eliminate the buzzer sound, press

the ALARM button.

8. Press the START button to begin. The DRYING

indicator light will turn on and will stay on, even

during the delay. The indicator light will remain

on until you open the dryer door.

During the drying programme, you can check on

your laundry and take out items that are dry

while others continue drying. When you close

the door again, press the START button in order

to resume drying.

9. About 10 minutes before the programme is

completed, it enters the final COOL TUMBLE

phase (fabrics are cooled), which should always

be allowed to complete.

10. The buzzer will warn you when drying is

complete. Open the door, take the laundry out,

clean the filter and replace it (see Maintenance).

11. Unplug the dryer.

Start and Programmes

GB

7

Programmes

Programme

What it does... How to set it... Note:

Automatic

Drying

(average loads)

Dries completely:

your clothes are ready to be

worn.

For average loads (from 1 to

3kg) of Cotton , polycotton

or synthetics .

! If you select LOW HEAT,

this programme will not dry

your clothes. For Acrylic

fibres or small loads select

Timed Drying.

This programme can also be

used for large loads if you

require a slightly drier result.

1. Select HIGH HEAT

by pressing the HEAT button.

2. Position the PROGRAMMES knob

on .

3. Press the START button , the

ACTIVE light will turn on.

Automatic

Drying

(large loads)

Dries completely:

your clothes are ready to be

worn.

For large loads (from 3 to 6kg) of

Cotton .

! If you select LOW HEAT,

this programme will not dry

your clothes. For Acrylic

fibres or small loads select

Timed Drying.

This programme can also be

used for average loads if you

prefer a damper result.

Timed Drying

up to 120 minutes

Dries wet clothes that will be

ironed, Acrylic fibres , or small

loads (less than 1kg).

If you prefer a timed programme

can be used for other fabrics on

HIGH or LOW heat as appropriate

(see Laundry).

Consult suggested drying

times (see Laundry).

! This is not a drying

programme (see below).

1. Position the PROGRAMMES knob

on .

2. Press the START button , the

ACTIVE light will turn on.

Use to refresh fibres of clothing

(approximately 10 minutes).

1. Select required heat setting HIGH

HEAT or LOW HEAT by

pressing the HEAT button.

2. Position the PROGRAMMES knob

on the desired time.

3. Press the START button , the

ACTIVE light will turn on.

Easy Iron

Cool Tumble

Brief programme (approximately

10 minutes) that softens fibres of

clothing that is ready for ironing.

! This is not a drying

programme (see below).

Easy Iron Programme

‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which

fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle

relaxes the fibres and makes them easier to iron and fold.

! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.

For best results:

1. Do not load more than the maximum capacity.

These numbers refer to the dry weight:

Fabric Maximum load

Cotton and Cotton mixtures 2.5kg

Synthetics 2kg

Denim 2kg

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put

them away in the closet. Should this not be possible repeat the programme.

The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,

and less well on acrylic fibres and on materials such as Tencel®.

Start and Programmes

1. Select HIGH HEAT

by pressing the HEAT button.

2. Position the PROGRAMMES knob

on .

3. Press the START button , the

ACTIVE light will turn on.

1. Select HIGH HEAT

by pressing the HEAT button.

2. Position the PROGRAMMES knob

on .

3. Press the START button , the

ACTIVE light will turn on.

Cool Tumble Phase

This is the programmes’ final phase. Approximately 10 minutes before the finish, the knob advances automatically to

the Cool Tumble Phase. Heating elements turn themselves off and clothing is cooled down, after this the Buzzer will

sound (if selected) and the clothing is ready to be taken out.

! Always allow the dryer to complete this phase.

8

GB

Sorting your laundry

●

Check symbols on clothing labels to make sure

that the articles can be tumble dried.

●

Sort laundry by fabric type.

●

Empty pockets and check buttons.

●

Close zippers and hooks and tie loose belts and

strings.

●

Wring out each item in order to eliminate as much

excess water as possible.

! Do not load dripping wet clothes into the dryer.

Maximum load size

Do not load more than maximum capacity.

These numbers refer to dry weight:

Natural fibres: 6kg max (13lb)

Synthetic fibres: 3kg max (6.6lb)

! DO NOT overload the dryer as this could result in

reduced drying performance.

Typical load

Note: 1kg = 1000g (1lb = 16oz)

Clothes

Blouse Cotton 150g (5oz)

Other 100g (3oz)

Dress Cotton 500g (1lb 2oz)

Other 350g (12oz)

Jeans 700g (1lb 6oz)

10 nappies 1000g (2lb 3oz)

Shirt Cotton 300g (10oz)

Other 200g (7oz)

T-Shirt 125g (4oz)

Household Items

Duvet cover Cotton 1500g (3lb 5oz)

(Double) Other 1000g (2lb 3oz)

Large Tablecloth 700g (1lb 6oz)

Small Tablecloth 250g (9oz)

Tea Towel 100g (3oz)

Bath Towel 700g (1lb 6oz)

Hand Towel 350g (12oz)

Double Sheet 500g (1lb 2oz)

Single Sheet 350g (12oz)

At the end of a drying cycle, cottons could still be

damp if you grouped cottons and synthetics together.

If this happens simply give them an additional short

period of drying.

●

Note: The last 10 minutes of any time set is the

Cool Tumble, so allow for this when setting the time,

as this period will not dry your laundry.

Wash Care Labels

Look at the labels on your garments, especially when

tumble drying for the first time. The following symbols

are the most common:

May be tumble dried

Do not tumble dry

Tumble dry at high heat setting

Tumble dry at low heat setting

Items not suitable for tumble drying

●

Articles that containing rubber or rubber-like

materials or plastic film (pillows, cushions, or PVC

rainwear), any other flammable articles or objects

that contain flammable substances (towels soiled

with hair spray).

●

Glass fibres (certain types of draperies)

●

Items which have been dry cleaned

●

Items with the ITCL Code (see Special

clothing items). These can be cleaned with special

at-home dry cleaning products. Follow instructions

carefully.

●

Large bulky items (quilts, sleeping bags, pillows,

cushions, large bedspreads etc). These expand

when drying and would prevent airflow through

the dryer.

Laundry

GB

9

Special clothing items

Blankets and Bedspreads: acrylic items (Acilan,

Courtelle, Orion, Dralon) must be dried with special

care on LOW heat setting. Avoid drying for a long

period of time.

Pleated or creased garments: read the manufacturer’s

drying instructions on the garment.

Starched articles: do not dry these with non-starched

items. Make sure that as much of the starch solution is

removed from the load as possible before placing it in

the dryer. Do not over-dry: the starch will become

powdery and leave your clothing limp, which defeats

the purpose of starch.

Drying times

The table below presents APPROXIMATE drying times

in minutes. Weights refer to dry garments:

Cottons

High (full) Heat

Drying times 800-1000rpm in washing machine

Half Load Full Load

1kg 2kg 3kg 4kg 5kg 6kg

20-30 35-45 45-60 60-70 70-80 80-100

Synthetics

High (full) Heat

Drying times on reduced spin in washing machine

Half Load Full Load

1kg 2kg 3kg

20-30 35-45 45-60

Acrylics /

Low (gentle) Heat

Drying times on reduced spin in washing machine

Half Load Full Load

1kg 2kg

25-40 40-60

Times are approximate and can vary depending

upon:

●

Amount of water retained in clothes after spin

cycle: towels and delicates retain a lot of water.

●

Fabrics: items that are the same type of fabric but

different textures and thicknesses may not have

the same drying time.

●

Quantity of laundry: single items or small loads

may take longer to dry.

●

Dryness: If you are going to iron some of your

clothes, they can be taken out while still a bit

damp. Others can be left longer if you need them

to be completely dry.

●

Heat setting.

●

Room temperature: if the room where the dryer is

located is cold, it will take longer for the dryer to

dry your clothes.

●

Bulk: some bulky items can be tumble dried with

care. We suggest that you remove these items

several times, shake them out, and return them to

the dryer until finished.

! Do not over-dry your clothes.

All fabrics contain a little natural moisture, which

keeps them soft and fluffy.

Laundry

10

GB

! The appliance has been designed and built according

to international safety standards.

These warnings are given for safety reasons and must

be followed carefully.

General safety

●

This tumble dryer is not intended for use by

persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

●

This tumble dryer has been designed for home,

and not professional use.

●

Do not touch the appliance while barefoot or with

wet hands or feet.

●

Unplug the machine by pulling on the plug, not

the cord.

●

Children must not be in proximity of the dryer

when in use. After using the dryer, turn it off and

unplug it. Keep the door closed to make sure that

children do not use it as a toy.

●

Children should be supervised to ensure that they

do not play with the dryer.

●

The appliance must be installed correctly and

have proper ventilation. The air intake vents

behind the machine, the outlet vents and the vent

tube should never be obstructed (see Installation).

●

Never direct the vent tube outlet towards the air

intake at the back of the machine.

●

Never allow the tumble dryer to recycle exhaust air.

●

Never use the dryer on carpeting where the pile

height would prevent air from entering the dryer

from the base.

●

Check to see if the dryer is empty before loading it.

●

The back of the dryer could become very

hot. Never touch it while in use.

●

Do not use the dryer unless the filter is securely

in place (see Maintenance).

●

Do not use liquid fabric softeners in the dryer, add

it to the final rinse of your wash.

●

Do not overload the dryer (see Laundry) for

maximum loads.

●

Do not load items that are dripping wet.

●

Tumble dry items only if they have been washed

with detergent and water, rinsed and been through

the spin cycle. It is a fire hazard to dry items that

HAVE NOT been washed with water.

●

Carefully check all instructions on clothing labels

(see Laundry).

●

Do not dry garments that have been treated with

chemical products.

●

Never dry articles that are contaminated with

flammable substances (cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine, waxes,

wax removers and hair sprays), unless washed in

hot water with an extra amount of detergent.

●

Do not tumble dry rubber, rubber backed articles and

clothes, pillows fitted with foam rubber pads, foam

(latex foam), rubber, plastic, shower caps, waterproof

textiles, nappy pants or liners, polythene or paper.

●

Do not tumble dry large, very bulky items.

●

Do not tumble dry acrylic fibres at high temperatures.

●

Remove all objects from pockets, especially lighters

(risk of explosion).

●

Complete each programme with its Cool Tumble Phase.

●

Do not turn off the dryer when there are still warm

items inside.

●

Clean the filter after each use (see Maintenance).

●

Do not allow lint to collect around the dryer.

●

Never climb on top of the dryer. It could result in

damage.

●

Always follow electrical standards and requirements

(see Installation).

●

Always buy original spare parts and accessories

(see Service).

! WARNING: Never stop the dryer before the end of the

drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

Recycling and disposal information

As part of our continued commitment to helping the

environment, we reserve the right to use quality recycled

components to keep down customer costs and minimise

material wastage.

●

Disposing of the packaging material: follow local

regulations, so the packaging can be recycled.

●

To minimise risk of injury to children, remove the

door and plug - then cut off mains cable, flush

with the appliance. Dispose of these parts separately

to ensure that the appliance can no longer be

plugged into a mains socket.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimise the recovery and recycling of the materials

they contain and reduce the impact on human health

and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that

when you dispose of the appliance it must be

separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct disposal

of their old appliance.

Saving energy and respecting the

environment

●

Wring out items to eliminate excess water before

tumble drying (if you use a washing machine first,

select a high spin cycle). Doing this will save time

and energy during drying.

●

Always dry full loads - you save energy: single

items or small loads take longer to dry.

●

Clean the filter after each use to contain energy

consumption costs (see Maintenance).

Warnings and Suggestions

GB

11

Check the drum after each cycle

Turn the drum manually in order to remove small items

(handkerchiefs) that could have been left behind.

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel

cleaning agents to clean the drum.

A coloured film may start to appear on the stainless

steel drum, this may be caused by a combination of

water and, or cleaning agents such as fabric conditioner

from the wash. This coloured film will not affect the

dryer performance.

Cleaning

●

External parts in metal or plastic and rubber parts

can be cleaned with a damp cloth.

●

Periodically check the vent tube and any

permanent venting fixture to make sure that there

has been no accumulation of fluff or lint, and

remove it.

●

Remove lint that collects around the filter and the

outlet vents.

! Do not use solvents or abrasives.

! Your dryer uses special bearing components which

do not need lubrication.

! Have your dryer checked regularly by authorised

technicians to ensure electrical and mechanical safety

(see Service).

Maintenance and Care

Switching off the electricity

Unplug your dryer when not using it, when cleaning it

and during all maintenance operations.

Clean the filter after each cycle

The filter is an important part of your dryer:

it accumulates lint and fluff that is formed while drying.

Small items could also become trapped in the filter.

When finished drying, therefore, clean the filter by

rinsing it under running water or with your vacuum

cleaner. Should the filter become clogged up, the airflow

inside the dryer will be seriously compromised: drying

times lengthen and you will consume more energy. It

may also damage your dryer.

The filter is found in front

of the dryer trim

(see diagram).

Removing the filter:

1. Pull the plastic grip of

the filter upwards (see

diagram).

2. Clean the filter and

replace it correctly.

Ensure the filter is fully

located flush into the

tumble dryer trim.

! Do not use the dryer without replacing the filter..

12

GB

Troubleshooting

Problem:

The tumble dryer won’t start.

Drying cycle will not begin.

Its taking a long time to dry.

Possible causes / Solution:

●

The plug is not plugged into the socket, or not making contact.

●

There has been a power failure.

●

The fuse has blown. Try to plug another appliance into the socket.

●

You are using an extension cord? Try to plug the dryer’s power cord

directly into the socket.

●

The door is not closed securely?

●

The PROGRAMMES knob has not been set properly (see Start and

Programmes).

●

The START button has not been pressed (see Start and Programmes).

●

You have set a delayed time (see Start and Programmes).

●

The filter has not been cleaned (see Maintenance).

●

The temperature setting is not ideal for the type of fabric you are drying

(see Start and Programmes).

●

Auto Programmes require a HIGH temperature setting (see Start and

Programmes).

●

The correct programme has not been selected for the load (see Start

and Programmes).

●

The flexible vent tube is obstructed (see Installation).

●

The air intake vent is obstructed (see Installation).

●

The permanent ventilation flap on the storm cover is obstructed (see

Installation).

●

The items were too wet (see Laundry).

●

The dryer was overloaded (see Laundry).

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the

following troubleshooting suggestions:

GB

13

Spare Parts

This dryer is a complex machine. Repairing it yourself

or having a non-authorised person try to repair it could

cause harm to one or more persons, could damage

the machine and could invalidate the spare parts

warranty.

Call an authorised technician if you experience problems

while using the machine.

The spare parts have been designed exclusively for

this appliance and not for other uses.

Service

Before calling the Service Centre:

●

Use the troubleshooting guide to see if you can

solve the problem yourself (see Troubleshooting).

●

If not, turn off the dryer and call the Service Centre

closest to you.

What to tell the Service Centre:

●

name, address and post code.

●

telephone number.

●

the type of problem.

●

the date of purchase.

●

the appliance model (Mod.).

●

the serial number (S/N).

This information can be found on the data label inside

the door of the machine.

This appliance conforms to the following EC Directives:

- 2006/95/EC (Low Voltage Equipment)

- 89/336/EEC, 92/31/EEC and 93/68/EEC (Electromagnetic Compatibility)

Page is loading ...

AS600V

F

Français, 14

GB

English, 1

A

40

A

195066537.00 W

10/2007 - SIMLEX . Four Ashes, Wolverhampton

40

39

38-37

36

35-34

33-32

31

30

29

28

Hotpoint AS600V (EX) Owner's manual

This manual is also suitable for

Hotpoint AS600V (EX) Owner's manual

in other languages

Related papers

Other documents