Echo PAS-225 Quick start guide

Brand: Echo

Model: PAS-225

Category: Grass trimmers

Type: Quick start guide

This manual is also suitable for

Page is loading ...

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

MANUAL SAFETY SYMBOLS AND IMPORTANT

INFORMATION

Throughout this manual and on the product itself, you will nd safety alerts

and helpful, informational messages preceded by symbols or key words. The

following is an explanation of those symbols and key words and what they

mean to you.

The safety alert symbol accompanied by the word “DANGER” calls

attention to an act or condition which WILL lead to serious personal

injury or death if not avoided.

The safety alert symbol accompanied by the word “WARNING” calls

attention to an act or condition which CAN lead to serious personal

injury or death if not avoided.

The “NOTICE” message provides information necessary for the

protection of the unit.

Note: This “NOTICE” message provides tips for use, care and maintenance of

the unit.

GENERAL SAFETY REQUIREMENTS

Read and understand all provided literature before use. Failure to do so could

result in serious injury. Additional operating instructions are available from your

Authorized ECHO Dealer.

• Operating a poorly maintained unit can result in serious injuries to

operator or bystanders. Always follow all maintenance instructions as

written, otherwise serious personal injury can result.

• Use only approved attachments. Serious injury can result from the

use of a non-approved attachment combination.

• Do not attempt to modify this product. Serious injury can result from

the use of any modied product.

• Do not operate this unit when tired, ill, or under the inuence of

alcohol, drugs, or medication. Serious injury can result from the use

of this product in an impaired state.

• Moving parts can amputate ngers or cause severe injuries. Keep

hands, clothing and loose objects away from all openings. Always

stop engine, disconnect spark plug, and make sure all moving parts

have come to a complete stop before removing obstructions, clearing

debris, or servicing unit.

• Eye protection that meets ANSI Z87.1 or CE requirements must be

worn whenever you operate the unit.

• Operators who are sensitive to dust or other common airborne

allergens can need to wear a dust mask to prevent inhaling these

materials while operating unit. Dust masks can provide protection

against dust, plant debris, and other plant matter such as pollen.

Make sure the mask does not impair your vision, and replace the

mask as needed to prevent air restrictions.

Symbols /

Símbolos /

Symboles

Description /

Descripción /

La description

Symbols /

Símbolos /

Symboles

Description /

Descripción /

La description

Rotating Cutting Attachment /

Accesorio giratorio del corte /

Accessoire de rotation de la coupe

Direction of Blade /

Dirección de la hoja /

Direction de la lame

Thrown Objects /

Objetos lanzados /

Projection d’objets

DO NOT USE BLADES - Line Head Only /

NO USE HOJAS - Solo Cabeza de Llínea /

NE PAS UTILISER DE LAMES - tête de Ligne

Uniquement

Wear Slip Resistant Footwear /

Lleve calzado resistente a las resbaladuras /

Porter des chaussures antidérapantes

DO NOT USE LINE HEADS - Blades Only /

NO UTILICE CABEZALES DE LÍNEA: solo cuchillas/

NE PAS UTILISER DE TÊTES DE LIGNE - Lames

uniquement

Do not operate closer than 15 m (50 ft.) from electrical

hazards. Keep bystanders at least 15 m (50 ft.) away /

No opere a menos de 15 m (50 pies) de peligros

eléctricos. Mantenga a los transeúntes al menos a 15

m (50 pies) de distancia /

Ne pas opérer à moins de 15 m (50 pi) des risques

électriques. Gardez les passants à au moins 15 m (50

pi)

AVOID KICKOUT

Keep Bystanders and Helpers Away 15 m (50 ft.)

Beware thrown objects . Wear eye protection /

No permita a nadie que se acerque más de 15

metros (50 pies) de la máquina. Cuidado con los

objetos arrojados. Use protección para los ojos /

Ne laisser personne approcher à moins de 15 m (50

pi) Méez-vous des objets lancés.

Portez des lunettes de protection

Plan retreat path from falling objects /

Planique la ruta de retirada de los objetos que caen /

Planiez le chemin de retraite des objets qui tombent

Keep Bystanders and Helpers Away 15 m (50 ft.) /

No permita a nadie que se acerque más de 15

metros (50 pies) de la máquina /

Ne laisser personne approcher à moins de 15 m

(50 pi)

Purge Bulb /

Purga de bulbo /

Ampoule d’amorce

Rotating Cutting Attachment /

Accesorio de corte giratorio /

Accessoire de coupe rotatif

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

Use The Correct Personal Protection

ALWAYS WEAR NEVER WEAR

• Hearing Protection • Loose Clothing

• Eye Protection • Jewelry

• Heavy, Long Pants • Short Pants, Short Sleeve Shirt

• Boots • Sandals

• Gloves • Barefoot

• Long Sleeve Shirt • Long Hair Below Shoulders

Equipment Safety

Before Each Use Inspect:

• For damaged parts.

• Loose or missing fasteners.

• Cutting attachments for damage (cracked, chipped, etc.).

• Cutting attachment is securely fastened.

• Cutting shield is correct for cutting attachment and secured according

to this manual.

• Manufacturer recommended exible non-metallic line is installed in the

trimmer head.

• Guards are installed correctly.

• For fuel leaks from any point of the fuel system (tank to carburetor).

Use only ECHO attachments. Serious injury can result from the use

of a non-approved attachment combination. ECHO, INC. will not be

responsible for the failure of cutting devices, attachments or accessories

which have not been tested and approved by ECHO. Read and comply

with all safety instructions.

• Do not attempt to modify this product. Serious injury can result from

the use of any modied product.

• Check unit for loose or missing nuts, bolts, and screws. Tighten or

replace as needed.

• Inspect shield for damage and ensure that shield is properly installed,

and that the cut-o knife is securely in place. Replace if either is

damaged or missing.

• Check that the cutting attachment is rmly attached and in safe

operating condition.

• Manufacturer recommended exible non-metallic line is installed in the

trimmer head.

• Assure that throttle trigger, throttle trigger lockout, and stop switch all

work properly.

• Check that handle and harness (if included) are installed and adjusted

for safe, comfortable operation. See Assembly Section for proper

adjustment.

• Moving parts can amputate ngers or cause severe injuries. Keep

hands, clothing and loose objects away from all openings.

• ALWAYS stop engine, disconnect spark plug, and make sure all

moving parts have come to a complete stop before assembling unit,

removing obstructions, clearing debris, or servicing unit.

• Do not connect spark plug lead to spark plug until unit is ready for use.

• DO NOT start or operate unit unless all guards and protective covers

are properly assembled to unit.

• NEVER reach into any opening while the engine is running. Moving

parts can not be visible through openings.

• Position wiring safely to prevent snagging, separation of connectors,

or breakage during operation. Gather excess wire, and secure with

wiring clamp if provided on equipment, or tuck behind the air lter

area. Do not place wiring directly against hot engine components.

• Check wiring and connectors for nicks, cuts, exposed wire, or other

damage, and repair or replace as needed. Exposed wire or connectors

can cause shocks, sparks, and risk of re or explosion, resulting in

serious injury.

• Check wire terminals for secure connections.

• Periodically check fuel system (fuel lines, vent, grommet, fuel tank,

and fuel cap) for leaks especially if the unit is dropped. If damage or

leaks are found, do not use unit, otherwise serious personal injury

or property damage can occur. Have unit repaired by an authorized

servicing dealer before using.

Fuel Handling

• Fuel is VERY ammable. Use extreme care when mixing, storing or

handling, or serious personal injury will result.

• Mix and pour fuel outdoors where there are no sparks and ames.

• Slowly remove the fuel cap only after stopping the engine.

• Do not smoke while fueling or mixing fuel.

• Wipe spilled fuel from the unit.

• Move at least 3 m (10 ft) away from the fueling source and site before

starting engine.

Work Area

• Review the area to be cleared. Remove potential hazards such as

rocks, broken glass, nails, wire, or metal objects, which can be thrown.

• Clear the area of children, bystanders and pets.

• At a minimum, keep all children, bystanders and pets outside a 15 m

(50 ft) radius.

• Outside the 15 m (50 ft) zone, there is still a risk of injury from thrown

objects.

• Bystanders should be encouraged to wear eye protection.

• Avoid blowing debris towards people, pets, open windows, or vehicles

when using unit.

• If you are approached, stop the engine and cutting attachment.

• When a bladed unit is used, there is the added risk of injury to

bystanders being struck with the moving blade in the event of a blade

thrust or other unexpected reaction of the blade.

INFORMACIÓN IMPORTANTE Y SÍMBOLOS DE

SEGURIDAD DEL MANUAL

A lo largo de este manual y en el producto mismo, encontrará alertas de

seguridad y mensajes informativos de gran utilidad precedidos por símbolos o

palabras clave. A continuación se enumera una explicación de dichos símbolos

y palabras clave y su signicado.

El símbolo de alerta de seguridad acompañado por la palabra

"PELIGRO" destaca un acto o condición que LLEVARÁ a que se

produzcan lesiones personales graves o la uerte si no se evita.

El símbolo de alerta de seguridad acompañado por la palabra

"ADVERTENCIA" destaca un acto o condición que PUEDE llevar a que

se produzcan lesiones personales graves o la muerte si no se evita.

El mensaje adjunto proporciona información necesaria para proteger la

unidad.

Nota: Este mensaje adjunto proporciona sugerencias para el uso, cuidado y

mantenimiento de la unidad.

Page is loading ...

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

PAS-2620

PAS-225

ASSEMBLY / MONTAJE / ASSEMBLAGE

PAS-225

PAS-2620

Label shows minimum spacing for support

handle location.

La etiqueta muestra un espacio mínimo

para la ubicación del mango de soporte.

L’étiquette indique un espacement minimum

pour l’emplacement de la poignée de

support.

1a1a

Power Head Shaft to Lower Shaft Assembly / Eje de la cabeza de fuerza/eje inferior ensamblado / Arbre du moteur/arbre inférieur de

l’accessoire (Figures 2 & 2a)

1. Set Power Head/Shaft Assembly on a level surface.

2. Pull locater pin (A) out, and turn counterclockwise one-quarter turn to lock-out position.

3. Remove storage hook and cap from attachment drive shaft.

4. Carefully t attachment drive shaft assembly into coupler (B). Rotate the shaft (C) to make sure the inner

lower drive shaft engages the square upper drive shaft socket.

1. Fije el cabezal de impulsión/conjunto de eje en una supercie horizontal.

2. Tire del pasador guía (A) y gírelo hacia la izquierda ¼ de vuelta hasta la posición de bloqueo.

3. Retire el gancho de almacenamiento y la tapa del eje de transmission del accesorio.

4. Coloque cuidadosamente el conjunto del eje de transmission del accesorio en el acoplador (B). Gire el

eje (C) para asegurarse de que el eje de transmisión inferior interno se enganche en el casquillo del eje

de transmisión superior cuadrado..

1. Poser l’ensemble bloc moteur/arbre sur une surface plane.

2. Tirer sur la goupille de blocage (A) et la tourner de ¼ de tour vers antihoraire, en position déverrouillée.

3. Retirez le crochet et le capuchon de rangement de l'arbre d'entraînement de l'accessoire.

4. Fixez soigneusement l’ensemble arbre d’entraînement de l’accessoire (B) dans le coupleur (C). Faites

pivoter l’assemblage de l’arbre d’entraînement pour vous assurer que l’arbre d’entraînement inférieur

intérieur s’engage dans la douille carrée de l’arbre d’entraînement supérieur.

Handle Positioning / Posicionamiento Del Mango / Position Des Poignées (Figures 1 & 1a)

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

ASSEMBLE ACCESSORIES / ACCESORIOS DE MONTAJE / ASSEMBLER LES ACCESSOIRES

99944200540

Trimmer Attachment

Adaptador Para la Recortadora

L’accessoire de Débroussailleuse

99944200490

Blower Attachment

Acoplamiento del soplador

Installation de la souante

99944200601

Brushcutter Attachment

Accesorio para Desmalezadora

L’attachement Débroussailleuse

99944200470

Power Edger Attachment

Adaptador Para el Orillador

L’accessoire de Coupe-bordures

Note: * Your coupler can appear dierent than coupler shown. Earlier model power heads can have shorter

couplings.

* Lower bearing housing and head assembly must be in line with the engine.

* Some models can have an assembly line decal to assist in alignment.

5. Rotate locater pin (A) one-quarter turn clockwise to engage lower shaft hole. Make sure locater

pin is fully engaged by rotating the lower drive shaft. Locater pin should snap ush in coupler. Full

engagement will prevent further shaft rotation.

6. Secure lower shaft assembly to coupler by tightening clamping knob (D).

Nota: * Su acoplador puede parecer diferente al acoplador que se muestra. Los modelos anteriores de

cabezales eléctricos pueden tener acoplamientos más cortos.

* La carcasa del cojinete inferior y el conjunto de la cabeza deben estar alineados con el motor.

* Algunos modelos pueden tener una calcomanía de línea de ensamblaje para ayudar en la alineación.

5. Gire el pasador de localización (A) un cuarto de vuelta en el sentido de las agujas del reloj para

enganchar el oricio del eje inferior. Asegúrese de que el pasador localizador esté completamente

enganchado girando el eje de transmisión inferior. El pasador localizador debe encajar al ras en el

acoplador. El enganche completo evitará una mayor rotación del eje.

6. Asegure el conjunto del eje inferior al acoplador apretando la perilla de sujeción (D).

Remarque: * Votre coupleur peut sembler diérent de celui illustré. Les têtes d’alimentation des modèles

antérieurs peuvent avoir des couplages plus courts.

* Le boîtier de roulement inférieur et l’ensemble de tête doivent être alignés avec le moteur.

* Certains modèles peuvent avoir un décalque de ligne d’assemblage pour faciliter l’alignement.

5. Tourner la goupille de positionnement (A) d’un quart de tour dans le sens des aiguilles d’une montre

pour engager le trou d’arbre inférieur. Assurez-vous que la goupille de positionnement est complètement

engagée en faisant tourner l’arbre d’entraînement inférieur. La goupille de repérage doit s’encastrer dans

le coupleur. Un engagement complet empêchera une rotation supplémentaire de l’arbre.

6. Fixez l’ensemble de l’arbre inférieur au coupleur en serrant le bouton de serrage (D).

2a2a

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

Install Brushcutter Handle / Barrier Bar / Instale el mango de la desbrozado-

ra / la barra de barrera / Installer la poignée de débroussailleuse / barre de

barrière (Figures 3 & 3a)

Note: The Barrier Bar is required when using grass or weed blades. Do not use the

Barrier Bar as a handle.

1. Remove screw(s) (A), nut(s) (B), and backing plate or ller block (C) from support

handle (D). Keep backing plate or ller block for installation when barrier bar is not

installed.

2. Position support handle (D) on shaft.

3. Install Barrier Bar (E) using screw(s) (A), nut(s) (B).

Note: Support handle (D) must be at least 250 mm (10 in.) from center of rear handle grip.

4. Adjust handle position for comfortable operation. Tighten screw(s) securely.

Nota: Se requiere la barra de barrera cuando se usan hojas de hierba o hierba. No utilice

la barra de barrera como manija.

1. Retire los tornillos (A), las tuercas (B) y la placa de respaldo o el bloque de relleno

cuando la barra de barrera no esté instalada.

2. Coloque la empuñadura de soporte (D) en el eje.

3. Instale la barra de barrera (E) con los tornillos (A), las tuercas (B) .

Nota:Eempuñadura de soporte (D) debe estar al menos a 250 mm (10 pulgadas) del

centro de la empuñadura trasera.

4. Ajuste la posición del mango para una operación cómoda. Apriete los tornillos con

seguridad.

Remarque: La barre de barrière est requise lors de l’utilisation de brins d’herbe ou de

mauvaises herbes. N’utilisez pas la barre de barrière comme poignée.

1. Retirez les vis (A), les écrous (B) et la plaque d’appui ou le bloc de remplissage (C)

de la poignée maintien (D). Gardez le bloc de remplissage pour l’installation lorsque la

barre de barrière n’est pas installée.

2. Positionnez de la poignée maintien (D) sur l’arbre.

3. Installez la barrière (E) à l’aide des vis (A), des écrous (B) .

Remarque: De la poignée maintien (D) doit être à au moins 250 mm (10 po) du centre de

la poignée arrière.

4. Ajustez la position de la poignée pour un fonctionnement confortable. Serrez

fermement les vis.

Brushcutter Shield and Blade Installation / Instalación de escudo y cuchilla

de desbrozadora / Installation du bouclier et de la lame de la débroussaille-

use (Figure 4 & 4a)

Install the shield rst, then install the blade. Note the orientation of the components, install

as shown.

Shield

• Shield mounting lock nuts (A).

• Shield (B).

• Shield Plate (C).

• Shield mounting bolts (D).

Blade

• Upper blade plate (E).

• Blade (F).

• Lower blade plate (G).

• Hex nut (H).

• Cotter pin (I).

PAS-2620

PAS-225

3a3a

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

Instale el escudo primero, luego instale la cuchilla. Tenga en cuenta la orientación de los

componentes, instale como se muestra.

Proteger

• Tuercas de bloqueo de montaje (A).

• Escudo (B).

• Placa de escudo (C).

• Proteger los pernos de montaje (D).

Espada

• Placa superior de la cuchilla (E).

• Cuchilla (F).

• Placa inferior de la cuchilla (G).

• Tuerca hexagonal (H).

• Pasador (I).

Installez d’abord le bouclier, puis installez la lame. Notez l’orientation des composants, installez

comme indiqué.

Bouclier

• Écrous de blocage de montage du blindage (A).

• Bouclier (B).

• Plaque de protection (C).

• Protéger les boulons de montage (D).

Lame

• Plaque de lame supérieure (E).

• Lame (F).

• Plaque de lame inférieure (G).

• Écrou hexagonal (H).

• Goupille fendue (I).

Harness Adjustment and Balance of Unit / Ajuste del arnés y equilibrio de la unidad

/ Réglage du harnais et équilibre de l’unité (Figure 5 + 5a)

1. Loosen harness clamp screw.

2. Put on harness and attach unit to harness.

3. Slide harness clamp up (A) or down until unit balances with head or blade 200 mm ± 100 mm

(8 in ± 4 in) from the ground (B).

4. Tighten harness clamp screw.

5. Loosen handle clamp screw(s), and position handle for comfortable operation.

6. Tighten handle clamp screw(s) securely.

1. Aoje el gancho del arnés.

2. Póngase el arnés y sujete la unidad al arnés.

3. Deslice el gancho del arnés (A) hacia arriba o hacia abajo hasta que la unidad se equilibre con

el accesorio de corte o hoja 200 mm ± 100 mm (8 in ± 4 in) del terreno (B).

4. Apriete el tornillo del gancho del arnés.

5. Aoje los tornillo(s) de la abrazadera de mango, y posicioné mango para cómoda operación. .

6. Apriete con seguridad los tornillos del mango.

1. Desserrer la vis du collier de bandoulière.

2. Mettre le harnais sur l’épaule et y accrocher l’outil.

3. Faire glisser le collier (A) vers le haut ou vers le bas jusqu’à ce que l’outil soit équilibré, la tête

de coupe ou la lame 200 mm ± 100 mm (8 in ± 4 in) du sol (B).

4. Serrer la vis du collier de harnais.

5. Desserrez les vis de la poignée et positionnez la poignée pour un confort d'utilisation maximal.

6. Serrer fermement les vis de la poignée.

4a4a

15 m

50 ft

5a5a

Page is loading ...

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

STOP ENGINE / DETENER MOTOR / ARRÊT MOTEUR

(Figure 9)

OPERATION

• Read and understand all provided literature before use. Refer to online

Operators Manual for additional information.

• Never use wire or wire-rope that can break o and become a

dangerous “projectile”.

• Wear gloves, cuto knife is sharp, gearcase and surrounding area can

get hot.

• Failure to follow instructions can result in serious injury.

Operating Techniques - Nylon Line Head

Nylon line heads can be used for trimming, scything, edging, and scalping of

grass and light weeds.

Trimming

Feed the spinning line into the material to be cut. Tilt the line head to one side

to direct cutting debris away from you

• Straight shafts use counter-clockwise line head rotation - Tilt the cutting

head down on the right side (muer side) while cutting to direct cutting

debris away from operator. Feed the line gradually into the material you wish

to cut, avoiding contact with fences or other barriers.

Scything

Scything - Swing the cutting head in a level arc, gradually feeding the line into

the material being cut. Move forward with each arc to cut a swath. Width of

cutting swath depends on arc. Use a larger arc for a wider swath, or a smaller

arc for a narrow swath. Keep line head tilted to direct cutting debris forward or

away from you.

Edging and Scalping

Both of these are done with the nylon line cutting head tilted at a steep angle.

Scalping is removing top growth, leaving the earth bare. Edging is trimming

the grass back where it has spread over a pavement or driveway. During both

edging and scalping, hold the unit at a steep angle in a position where the

debris, and any dislodged dirt and stone, will not come back towards you even

if it ricochets o the hard surface.

WARM START / ARRANQUE EN CALIENTE / DÉMARRAGE À CHAUD

Note: If engine does not start after 2-3 pulls, use Cold Start Procedure.

Nota: Si el motor no arranca después de 2-3 tirones, use el Procedimiento de arranque en frío.

Remarque: Si le moteur ne démarre pas après 2-3 tractions du cordon, utiliser la procédure de démarrage à froide.

8a8a

8b8b

8c8c

8d8d

1. Throttle

Release throttle trigger and allow engine to return to idle before shutting

o engine.

2. Stop Switch

Move stop switch button (A) backward to STOP position.

1. Acelerador

Suelte el acelerador y permita que el motor vuelva marcha lenta antes de

apagar el motor.

2. Interruptor de parada

Mueva el botón del interruptor de parada (A) hacia atrás a la posición de

PARADA.

1. Relâcher la gâchette des gaz

Relâcher la gâchette des gaz et laisser le moteur tourner au ralenti avant

de l’arrêter.

2. Commutateur d’arrêt

Tirer le commutateur d’arrêt en position STOP.

(Figures 8 & 8a - 8d)

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

General

• Debris ows in direction of line head rotation. Change line head position to

assure debris ow is directed away from operator.

• Keep cutting line away from wire fences to avoid entanglement.

• Operate trimmer only with cutting head below knee height.

Operating Techniques - metal or plastic blade

Brush cutter blades can be used to cut and trim a wide variety of matereials,

refer to the blade selection section for determining the correct blade for the

application.

Scything (3, 8, and 80 tooth weed/grass, and brush blades)

• To cut large sections of eld grass and weeds swing the cutting

head in a level arc, gradually feeding the blade into the material

being cut. Adjust throttle speed according to your work.

• Do not swing the main pipe with arms. Turn hips to swing the

blade horizontally from right to left, and cut weeds on the left

side of the blade.

• Do not scythe back and forth as the grass can scatter and

kickout can occur easily.

• Tilt blade left by 5 to 10 degrees so that cut grasses will push

left, making progress easier.

• Move forward with each arc to cut a swath.

• Width of cutting swath depends on arc. Use a larger arc for a

wider swath, or a smaller arc for a narrow swath. Suggested

cutting width is about 1.5 m (4.9 ft).

• When scything large brush up to 0.5” diameter from right to left,

avoid cutting with highlighted section.

Reaction Forces

• The cutting attachment will continue to rotate even after the throttle is

released, maintain control of the unit until it has come to a complete

stop.

• Blade thrust can occur when the spinning blade contacts an object

that it does not immediately cut. Following proper cutting techniques

will prevent blade thrust.

• Blade thrust can be violent enough to cause the unit and/or operator to

be propelled in any direction, and possibly lose control of the unit.

• Blade thrust can occur without warning if the blade snags, stalls or

binds.

• Blade thrust is more likely to occur in areas where it is dicult to see

the material being cut.

Push or Pull - Kickout

During normal use, operating a brushcutter with a circular metal blade can

produce sudden strong reaction forces that are dicult to control. Strong

reaction forces can cause a loss of balance or loss of control of the equipment,

resulting in serious injury to operator and bystanders.

Understanding what causes these reactive forces can help you to avoid them,

and can help you to maintain control of the equipment if you experience a

sudden reaction during cutting. Reactive forces occur when the force being

applied by the cutting teeth of a blade meet resistance, and some of the cutting

force is directed back toward the equipment. The greater the cutting force or

the amount of resistance, the greater the reactive force.

Push and Pull Forces

Push and pull forces are reactive forces that push the

equipment directly toward the operator, or that pull the

equipment directly away from the operator. These forces are

the result of cutting on the sides of the blade. The direction of

the force depends on the side of the blade being used, and the

direction of blade rotation at the point of contact. The reactive

force is in the opposite direction of blade rotation at the contact

point, regardless of where the contact is being made. These

types of reactive forces are also called “Blade Thrust.”

As shown in the illustration, a blade turning counterclockwise

will cause the equipment to pull away from the operator if the

point of cutting resistance is on the left side of the blade. If

the point of cutting resistance is on the right side of the blade,

the equipment will push back toward the operator. In both

examples, the reactive force is in the opposite direction of

blade rotation at the contact point where resistance occurs.

Kickout

Kickout is also a reactive force caused by resistance to

cutting, but the direction of blade thrust is lateral (to the left

or right of the blade), instead of forward or back toward the

operator. In most cases, Push, Pull, and Kickout can be

reduced or eliminated by:

• Using the correct blade for the cutting job.

• Using properly sharpened blades.

• Applying consistent, even force to the blade during the

cut.

• Avoiding obstacles and ground hazards.

• Using extra care when cutting harder materials such as

extremely dry brush, saplings, and small trees.

• Cutting from a stable, secure position.

Blade Cutting Problems

Binding - Blades can bind in the cut if dull

or forced. Binding can damage blade, and

result in blade breakage or injury from

fragments and ying debris. If a blade binds

in a cut, don’t try to get it out by applying

“up and down” force to pry the cut open.

Applying prying force to the blade can bend

the blade, and result in blade failure and

injury.

To free a blade that is bound in the cut,

stop the engine, and support the trimmer

or brushcutter to keep stress o the blade.

Push the tree away from the entry point of

the cut to open the cut, and pull the blade

directly away from the cut in a straight-line

motion. Use caution when releasing the tree to avoid being struck by spring-

back or falling.

Inspect the blade for damage before proceeding. Sharpen teeth if dull, or

replace blade if cracked, bent, missing teeth, or otherwise damaged.

To prevent binding:

• Keep blades sharp.

• Avoid excessive pressure during cuts.

• Don’t exceed cutting capacity of blade.

• Don’t use blades with damaged or missing cutting teeth.

• Don’t rock blades in cut.

Operation With Blades

Metal blades are very sharp and can cause severe injuries, even if

engine is o and blades are not moving. Avoid contact with blades. Wear

gloves to protect hands.

Blade use demands specic brush cutter conguration. Operation

without specied shield, barrier bar or U-handle, and harness can result

in serious personal injury. Follow installation instructions.

Material

to be

Cut

Grass Weed/

Grass

Weed/

Grass

Brush

(<0.5”)

Clearing

(<2.5”)

Cutting

Attachment

Nylon

line head

Included

Maxi-Cut

head,

Pro Maxi-

Cut head

3 Tooth

Blade,

8 Tooth

Blade

80 Tooth

Blade

22 Tooth

Blade

Shield Shield

Included

with unit

Included

with unit

Included

with Blade

Included with

Blade

Handle Handle

Included

U-Handle*

or Support

Handle w/

Barrier Bar

U-Handle*

or Support

Handle w/

Barrier Bar

U-Handle*

or Support

Handle w/

Barrier Bar

U-Handle*

or Support

Handle w/

Barrier Bar

Harness Not

Required

Not

Required

Supplied

w/Kit

Supplied

w/Kit

Supplied

w/Kit

*ANSI standards require brushcutters be equipped with a barrier bar or

restrictive harness. U-Handle ensures a higher safety factor.

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

Use only ECHO approved parts. Failure to use the correct parts can

cause the blade to y o. Seriously injury to the operator and / or

bystanders can occur.

Before Each Use When Using A Blade:

• Verify the handles are installed according to the manufacturers

instructions. Use only ECHO approved parts. Failure to use the correct

parts can cause the blade to y o. Seriously injury to the operator

and / or bystanders can occur.

• Arbor diameter of upper blade plate must match arbor diameter of

blades.

• For barrier bar, follow installation instructions.

• Make sure blade is secured properly.

• A new cotter pin is required each time a blade is installed.

• Shoulder harnesses can be used on all trimmers and brushcutters to

reduce operator fatigue. Brushcutters over 7.5 kg (16.5 lbs.) dry weight

(without fuel) and U- handle brushcutters REQUIRE a double shoulder

harness.

Note: The barrier bar is used to restrict rearward movement of the unit. The

barrier bar is not a handle and should not be gripped when using or

carrying the unit.

Blade Selection

The type of blade used MUST be matched to the type and size of material

cut. An improper or dull blade can cause serious personal injury. Blades

MUST be sharp. Dull blades increase the chance of kick-out and injury to

yourself and bystanders. Never use an edging blade, circular saw blade,

or any other type of unapproved blade.

• 3-Tooth Grass/Weed Blades can be used wherever the nylon line head

is used. DO NOT use this blade for heavy weeds or brush.

• 8 Tooth Weed/Grass Blade is designed for grass, garden debris and

thick weeds up to 19 mm (0.75 in.) diameter. DO NOT use this blade for

brush or heavy woody growth.

• 80 Tooth Brush Blade is designed for cutting brush and woody growth

up to 13 mm (0.5 in.) diameter.

• 22 Tooth Clearing Blade is designed for dense thickets and saplings

up to 64 mm (2.5 in.) diameter.

A trimmer-brushcutter with a metal blade can cause serious injuries if

handled improperly.

Always use extreme care when carrying or

handling the equipment to avoid contact with the

cutting edges of the blade. Use the optional blade

cover when unit is not in use.

Keep blades in protective packaging until ready

to install. Store blades safely after removal to

prevent injury from accidental contact.

Use blade protectors to protect blade teeth during

unit transportation.

Use Shoulder/Waist Harness

Use of the shoulder/waist harness is

recommended for ALL Trimmer/brushcutter

use, not just blade operation. The shoulder/

waist harness when used in a trimming

operation with nylon line head suspends

the trimmer from the operator’s shoulder

and reduces operator fatigue.

During blade operation, the same fatigue

reduction is achieved. Safety to the

operator is also enhanced by reducing

the possibility of blade contact with the

operator’s hands and feet by restricting

trimmer movement.

Make sure the warning sign on the back of

the shoulder harness can be read easily.

Note: In case of Emergency, disconnect the trimmer from the harness.

Operation with Edger

Before edging, be sure to read and understand the entire online

Operator’s Manual to avoid serious injury.

Edger Blade Adjustment and Operation Techniques

1. Before edging, water the area to soften the ground to make edging easier.

2. Before edging, check the area and remove all obstacles and objects that

could be thrown.

3. Plan to edge regularly to make it easier to keep a neat edge and to avoid

having to make more than one pass.

Note: Blade depth can have to be adjusted due to dierences in height

between the hard surface and the top of the grass.

The complete unit, specically the drive shaft

assembly and muer exhaust area can become

very hot during use. Avoid contact during and

immediately after operation, otherwise serious

personal injury can result.

Never adjust blade height with engine running,

otherwise serious personal injury can result.

4. Loosen adjustment knob (A).

Move wheel up to increase

cutting depth, or down to

decrease cutting depth. A depth

of 13 mm (0.5 in.) is optimal.

Tighten adjustment knob (A).

5. Before edging, plan your

direction of travel so that the

unit will always be positioned

on your right side and so that

you walk on a hard surface

whenever possible.

6. Position edger as shown.

7. When starting to edge, run

the engine at full throttle, and

lower the blade gently into the

ground, being careful not to hit

the concrete with the blade.

8. Don’t force the blade. Move

only as quickly as the blade

will allow.

Operation with Blower

Moving parts can amputate ngers or cause severe injuries. Keep hands,

clothing and loose objects away from all openings. Always stop engine,

disconnect spark plug, and make sure all moving parts have come

to a complete stop before removing obstructions, clearing debris, or

servicing unit. Blower housing can contain shredder blades and other

sharp edges that can cause serious injuries if touched, even if engine is

o and blades are not moving. Wear gloves to protect hands from sharp

edges and hot surfaces.

Always wear safety glasses, hearing protection and a face lter mask or

serious personal injury can result. Do not point the blower pipe in the

direction of people or pets.

This blower should be used for clearing leaves, grass, and dust in yards,

gardens, driveways, and parking lots only.

Page is loading ...

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

Utiliser uniquement une vitesse réduite pour eectuer les taches légères

ou pour respecter les réglementation locales relatives au bruit. Un

fonctionnement continu à basse vitesse risque de favoriser les dépôts

de résidus d’essence/huile sur le piston et un calaminage rapide du

pare-étincelles, entraînant la surchaue et l’endommagement du moteur.

Pour limiter les dépôts nuisibles, faire tourner le moteur à plein régime

pendant au moins 5 minutes toutes les heures, et inspecter/nettoyer le

pare-étincelles au bout de 40 heures de fonctionnement.

Pour éviter des dommages au moteur causés par un surrégime, ne pas

bloquer le tube de souante.

1. N’utiliser qu’aux heures permises.

2. Laisser le moteur se réchauer au ralenti pendant quelques minutes.

3. Utiliser une inférieure pour souer des débris des surfaces dures.

4. La vitesse additionnelle peut être nécessaire pour essuyer les débris, la

neige, etc. des pelouses et les lits de eur.

Remarque: Ne jamais utiliser une vitesse supérieure à ce qui est nécessaire

pour un travail donné. Ne pas oublier que plus le régime est élevé,

plus le moteur est bruyant. Minimaliser la poussière en travaillant à

bas régime. Ne pas chasser les débris sur la propriété d’autrui. Soyez

intelligent – Montrezvous bon voisin.

MAINTENANCE PROCEDURES

Idle Speed Adjustment

Every unit is run at the factory and the carburetor is set in compliance

with emission regulations. Carburetor adjustments, other than idle

speed, must be performed by an authorized ECHO dealer.

1. If a tachometer is available, idle speed

screw should be set to 3000 RPM. Turn

idle screw clockwise to increase idle

speed; counterclockwise to decrease idle

speed. If a tachometer is not available,

see your authorized ECHO dealer.

Replace Nylon Line:

Speed Feed™

1. Cut one piece of 2.0 mm (0.80 in.) or 2.4 mm (0.95 in.) line to

recommended length of 6 m (20 ft.).

2. Align arrows on top of knob with opening

of eyelets.

3. Insert one end of trimmer line into eyelet

and push line until equal lengths extend

from trimmer head.

4. Hold trimmer head while turning knob

clockwise to wind line onto spool until

about 13 cm (5 in.) of each line remains

exposed.

3000 RPM \ TR/MIN

Sharpening 8-Tooth Metal Blade

Several styles of metal blades are approved for

use on the Brushcutter. Only the 8-tooth blade

can be sharpened during normal maintenance.

The clearing and 80-tooth blades require professional

service for sharpening.

Before sharpening, CLOSELY inspect blade for

cracks (look at the bottom of each tooth and

the center mounting hole closely), missing teeth

and bending. If ANY of these problems are

discovered, replace the blade.

When sharpening a blade, always remove the

same amount of materials from each tooth to

maintain balance. A blade that is not balanced will cause unsafe handling due

to vibration and can result in blade failure.

1. File each tooth at a 30° angle a specic

number of times, e.g., four strokes per

tooth. Work your way around the blade until

all teeth are sharp.

2. DO NOT le the ‘gullet’ (radius) of the tooth

with the at le. The radius must remain. A

sharp corner will lead to a crack and blade

failure.

30º

If an electric grinder is used,

use care not to overheat teeth,

do not allow tips/tooth to glow

red or turn blue. DO NOT place

blade in cooling water. This

will change the temper of the

blade and could result in blade

failure.

3. After sharpening teeth, check

each tooth radius for evidence

of a square (sharp) corner. Use

the round (rat tail) le to renew

the radius.

Edger Blade Replacement

Parts required: Blade, new split pin.

Note: Replace blade when it is

bent, damaged, or worn

shorter than 152.4 mm (6

in.).

1. Remove split pin (A).

2. Align hole in inner blade

adapter (B) with notch in gear

housing, and insert locking tool

(G) to prevent PTO shaft (C)

from rotating.

3. Remove L.H. blade nut (D) by

turning clockwise. Remove

outer blade adapter (E), and

blade (F).

4. Install and center blade (F) on

inner blade adapter (B).

5. Install outer adapter (E) and

nut (D). Tighten nut (D) rmly,

turning counterclockwise.

Note: Never reuse old split pin.

6. Install new split pin (A) to

secure nut, and bend both legs

of pin counterclockwise around

PTO shaft (C).

30º

Cutting Tooth Area /

Área de corte de dientes /

Zone de dent de coupe

Gullet Radius /

Radio de oro /

Rayon d'or

Cutting Tooth Radius /

Radio de diente de corte /

Rayon de dent de coupe

Page is loading ...

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

EMISSIONS CONTROL COMPONENTS

The use of emission control components other than those specically

designed for this unit is a violation of federal law.

Maintain Air Filter

1. Close choke, remove air lter cover, clean air cleaner area, clean or replace

lter (if damaged).

Maintain Spark Plug

Note: PAS-225; Use only NGK BPM8Y (BPMR8Y in Canada) spark plug

otherwise severe engine damage can occur.

PAS-2620; Use only NGK CMR7H spark plug otherwise severe engine

damage can occur.

1. Adjust spark plug gap by bending outer electrode to a 0.65 mm (0.026 in)

gap.

2. Tighten spark plug to 150 - 170 kgf•cm (130 - 150 in•lbf).

Maintain Spark Arrestor Screen

Parts Required: Spark Arrestor Screen, Gasket

1. Remove spark plug lead and engine cover or muer cover if applicable.

2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering

cylinder.

3. Remove spark arrestor screen cover, gaskets, and screen, from muer

body.

4. Clean carbon deposits from muer components.

Note: When cleaning carbon deposit, be careful, do not damage the catalytic

element inside muer (If equipped with catalytic element).

5. Replace screen if it is cracked, plugged, or has holes burned through.

6. Assemble components in reverse order.

Fuel is VERY ammable. Use extreme care when mixing, storing or

handling, or serious personal injury will result.

Maintain Fuel Filter

1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel

tank. Pull the fuel lter from the fuel tank. Remove the lter from the line

and install the new lter (do not damage fuel line when removing the fuel

lter from the tank).

EMISSION CONTROL (EXHAUST & EVAPORATIVE)

• CARB and EPA Emissions Control Information.

• The emission control system for the engine is EM (engine modication) and,

if the second to last character of the Engine Family on the Emission Control

Information label (sample below) is “B”, “C”, “K”, or “T”, the emission control

system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission

control system is EVAP (evaporative emissions). Evaporative emissions for

California models are only applicable to fuel tanks and fuel feed lines.

• An Emission Control Label is located on the engine. (This is an EXAMPLE

ONLY, information on label varies by ENGINE FAMILY).

• Product Emission Durability (Emission Compliance Period).

• The 50 or 300 hour emission compliance period is the time span selected

by the manufacturer certifying the engine emissions output meets applicable

emissions regulations, provided that approved maintenance procedures are

followed as listed in the Maintenance Section of this manual.

SERVICE

• Service of this product during the warranty period must be performed by

an Authorized ECHO Service Dealer. For the name and address of the

Authorized ECHO Service Dealer nearest you, ask your retailer or call

1-800-432-ECHO (3246). Dealer information is also available on our Web

Site www.echo-usa.com. When presenting your unit for Warranty service/

repairs, proof of purchase is required.

Cancer and Reproductive Harm.

www.P65Warnings.ca.gov

Transportation

• During operation the muer or catalytic muer and surrounding cover

can become hot. Always keep exhaust area clear of ammable debris

during transportation or when storing, otherwise serious property

damage or personal injury can result.

• Always secure the unit during transportation to prevent turnover, fuel

spillage, and damage to the unit.

Short-term Storage

• Store unit in a dry, dust free place, out of the reach of children.

• Do not store in enclosure where fuel fumes can accumulate or reach an

open ame or spark, or serious personal injury will result.

Long-term Storage (Over 30 Days)

• Place the stop switch in the “OFF” position.

• Clean the exterior of the product.

• Perform all periodic maintenance.

• Tighten all the screws and nuts.

• Drain the fuel and run the unit until it stops.

• Allow engine to cool.

• Store unit in a dry, dust free place, out of the reach of children.

Storage Hook Installation

1. Insert small end of hook into locating hole on

attachment shaft.

2. Slide plastic cap onto end of attachment shaft.

Page is loading ...

QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE

RAPIDE

PAS-225 / PAS-2620

Pro Attachment Series™

Use only ECHO attachments for these models. Serious injury can result from the use of non ECHO attachment combinations. Read and comply with

all safety instructions listed in this manual and attachment manual. ECHO, INC. will not be responsible for the failure of cutting devices, attachments

or accessories which have not been tested and approved by ECHO for use with these units.

Recommended Optional Attachments / Adjuntos opcionales recomendados /

Pièces jointes facultatives recommandées

Optional Attachments / Adjuntos opcionales / Pièces jointes en option Part Number / Número de pieza / Numéro d’article PAS-225 PAS-2620

Articulating Hedge Trimmer / Recortadora de setos articulada / Taille-haie

articulé

99944200596

Brushcutter / Desbrozadora / Débroussailleuse 99944200601

Curved Shaft Edger / Borde de eje curvo / Coupe-bordure à arbre

incurvé

99944200470

Straight Shaft Edger / Bordeadora de eje recto / Coupe-bordure à

arbre droit

99944200475

Shaft Hedge Trimmer Accessory / Adaptador Para el Cortasetos / L’accessoire

de Taille-haie

99944200486

Mid-Reach Hedge Trimmer / Cortaseto de Medio Alcance / Taille Haie à Portée

Moyenne

99944200640

0.91 m (3.0 ft.) Extension Attachment / Extensión de

91cm / Accessoire rallonge 91 cm *

* For use with: Articulating Hedge Trimmer, Hedge Trimmer, and Power

Pruner™ Attachments ONLY.

* Para usar con: Cortacésped articulado, Recortador de setos y accesorios

Power Pruner ™ SOLAMENTE.

* À utiliser avec: taille-haie articulé, taille-haie et accessoires Power Pruner ™

UNIQUEMENT.

99944200536

Blower / Acoplamiento del soplador / Installation de la souante 99944200490

Tiller - Cultivator / Caña del timón - cultivador / Taller - cultivateur 99944200513

Speed-Feed® Trimmer 99944200540

Rapid Loader™ Curved Shaft Trimmer 99944200615

Pro-Torque Trimmer™ 99944200545

Bed Redener / Adaptador Rebordeadora de Arriates / L’ accessoire de

Délimiteur de Parterre

99944200465

Power Pruner® 99944200532

Pro Paddle™ 99944200620

Pro Sweep™ 99944200553

Echo PAS-225 Quick start guide

Brand: Echo

Model: PAS-225

Category: Grass trimmers

Type: Quick start guide

This manual is also suitable for

Download PDF

report

in other languages

français: Echo PAS-225 Guide de démarrage rapide
español: Echo PAS-225 Guía de inicio rápido

Echo PAS-225 Quick start guide

This manual is also suitable for

Echo PAS-225 Quick start guide

in other languages

Related papers

Other documents