Livex Lighting 40726-34 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
40726-34
Type
Operating instructions

Livex Lighting 40726-34 is a versatile and stylish lighting fixture that can be used to enhance the ambiance of any room. With its adjustable height and multiple light sources, it can be customized to meet your specific needs.

The fixture is easy to install and comes with all the necessary hardware. It features a black finish that will complement any décor. The fixture is also dimmable, so you can create the perfect lighting for any occasion.

Here are some of the key features of the Livex Lighting 40726-34:

  • Adjustable height: The fixture can be adjusted to a height of 72 inches.
  • Multiple light sources: The fixture has three light sources, so you can customize the lighting to meet your needs.

Livex Lighting 40726-34 is a versatile and stylish lighting fixture that can be used to enhance the ambiance of any room. With its adjustable height and multiple light sources, it can be customized to meet your specific needs.

The fixture is easy to install and comes with all the necessary hardware. It features a black finish that will complement any décor. The fixture is also dimmable, so you can create the perfect lighting for any occasion.

Here are some of the key features of the Livex Lighting 40726-34:

  • Adjustable height: The fixture can be adjusted to a height of 72 inches.
  • Multiple light sources: The fixture has three light sources, so you can customize the lighting to meet your needs.
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
40722 40726
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1.Shut off the power at the circuit breaker box. Remove old fixture and all
hardware from Junction Box. Carefully unpack your new fixture and lay out all
the parts on a clear area. Take care not to lose any small parts necessary for
installation.
3. Slide the electrical wires through the tube(J)/(I)/(H) and canopy(F).
4. Raise the tube(J) to the coupling of the fixture body(K), raise the tube (I) ,tube
(H) to the screw pipe nipple in order , then by turning it clockwise until tighten.
Raise the canopy(F) and ground wire onto the pipe nipple of the tube(H), lock it
securely with the lock washer and hex nut.
5. End of pipe nipple screw(C) into single bar (D), place lock washer (B) over end
of nipple protruding through single bar and lock it securely with the hex nut (A).
Take this single bar assembly to junction box with junction box screws (E),
tighten screws securely with screwdriver. The side of the single bar marked
"GND" must face to out. The junction box is not included.
6. While holding the fixture body towards the ceiling , connect the electrical wires
as Shown in Fig.2, making sure that all wire nuts are secured. You may have to
wrap the connections with electrical tape. If your outlet has a ground wire (green
or bare copper), connect the fixture ground wire to it. Otherwise connect fixture’s
ground wire directly to the Single bar with the green screw provided. After wires
are connected, tuck them carefully inside the Junction Box.
7. Raise the fixture body on to the Junction box, aligning screws on single bar with
mounting hole in canopy and lock it securely with the finial (G). Raise the
glass(M) to the lamp holder, lock it securely with the check ring(N). Raise the
finial(L) to the end tube of the fixture body, by turning it clockwise until tighten.
8. Install the light bulbs(not included) in accordance with the fixture specifications
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
Your installation is now complete. Return power to the junction
box and test the fixture.
Wire
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper(Ground)
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us online at: WWW.LIVEXLIGHTING.COM
©COYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20151240722
FIG.2
FIG.1
  • Page 1 1

Livex Lighting 40726-34 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
40726-34
Type
Operating instructions

Livex Lighting 40726-34 is a versatile and stylish lighting fixture that can be used to enhance the ambiance of any room. With its adjustable height and multiple light sources, it can be customized to meet your specific needs.

The fixture is easy to install and comes with all the necessary hardware. It features a black finish that will complement any décor. The fixture is also dimmable, so you can create the perfect lighting for any occasion.

Here are some of the key features of the Livex Lighting 40726-34:

  • Adjustable height: The fixture can be adjusted to a height of 72 inches.
  • Multiple light sources: The fixture has three light sources, so you can customize the lighting to meet your needs.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents