TTX Flow shock absorber for KTM SX/SX-F/XC/XC-F
KT 1892/93/94
Mounting Instructions
Note!1
Please note that there can be small differences
between your product and the images in
these instructions.
Note!1
Please note that during storage and transport,
especially at high ambient temperature, some
of the oil and grease used for assembly may
leak and stain the packaging. This will not cause
damage to the product, wipe off the excessive
oil or grease with a cloth.
Note!1
No spring included in this kit. See the spring
guide in this folder or contact an Öhlins dealer
for advice.
Note!1
Before you install this product, check the kit
contents. If anything is missing, please contact
an Öhlins dealer.
Warning!⚠
Before you install this product, read the Öhlins
Owner’s manual. This product is an important
part of the vehicle and the vehicle stability.
Kit Contents
Description Part No Pcs
Shock absorber KT 1892
KT 1893
KT 1894
1
Spring clip 15087-01 1
Washer 10.5x22x2 00153-06 1
Owner’s manual 07253-03 1
Sticker Öhlins 1
2
MOUNTING INSTRUCTIONS
Install the spring
Note!1
Install the spring on the shock absorber before
you install the shock absorber on the vehiicle.
1
Measure the spring free length (A).
2
Loosen the lock nut so that you can move the
spring platform as far up as needed to install the
spring.
3
Put the shock absorber up-side-down in a vice.
lnstall the spring.
4
Install the spring clip by sliding it over the end
piece and the stop washer. See view from
above for unlocked orientation.
5
Turn the spring clip or the end piece 90° and
pull it back to the stop washer. See view from
above for locked orientation.
Note!1
If a spring assembly tool is used, the spring
can be compressed by pushing on the spring
clip and rotate the end piece to reach locked
orientation.
6
Measure the spring length. Adjust the spring
preload to the recommended setup data, found
in this Mounting Instruction.
Caution!✋
Tighten the preload lock nut before riding the
vehicle.
90° 90°
Lock nut
Spring platform
Spring
A
Spring clip
3
MOUNTING INSTRUCTIONS
Setting preload
1
Loosen the preload lock nut. Use a C-spanner.
2
Turn the spring by hand to the desired position.
The spring platform has a grip function,
therefore, by turning the spring you will move
the spring platform.
3
Tighten the preload lock nut.
Note!1
Make sure the spring platform is not rotating
when tightening the lock nut.
4
Warning!⚠
We strongly recommend to let an Öhlins dealer
install this product.
Warning!⚠
If you work with a lifted vehicle, make sure that it
is safely supported to prevent it from tipping over.
Note!1
When you work with this product, see the
vehicle service manual for vehicle specic
procedures and important data.
Note!1
Before you install this product clean the vehicle.
1
Put the motorcycle on a work stand so that the
rear wheel barely touches the ground.
Install the Shock Absorber
2
Refer to the vehicle manual to install the Öhlins
shock absorber.
3
Use the washer 00153-06 together with OEM
screw when installing lower end of the shock
absorber.
Note!1
Lower the vehicle so that the suspension
is slightly compressed before you tighten
the screws.
Caution!✋
Make sure that you tighten all screws to the
correct torque and that nothing fouls or restricts
movement of the shock absorber/front fork/
steering damper when the suspension is fully
compressed or extended.
Washer
00153-06
MOUNTING INSTRUCTIONS
5
SPRING GUIDE
KT 1893: KTM 250/350 SX-F & KTM
250/300 XC & KTM 250/350/450 XC-F &
Husqvarna FC 250/350
Rider’s weight*
kg/pounds
Spring
part no
Spring rate
N/mm
60/132 06310-03 38
65/143 06310-03 38
70/154 06310-04 40
75/165 06310-04 40
80/176 06310-05 42
85/187 06310-05 42
90/198 06310-06 44
95/209 06310-06 44
100/220 06310-07 46
105/231 06310-08 48
110/242 06310-09 50
115/253 06310-10 52
SETUP DATA
Length KT 1892/93/94 477 mm
Stroke KT 1892/93/94 138 mm
Spring preload approx. 10 (5) mm (turns)
Compr. low speed 6 clicks
Rebound 9 clicks
Free Sag and Ride Height
R1-R2 35±5 mm
R1-R3 100±5 mm
MOUNTING INSTRUCTIONS
KT 1892: KTM 125/150/250 SX &
Husqvarna TC 125/250
Rider’s weight*
kg/pounds
Spring
part no
Spring rate
N/mm
60/132 06310-01 34
65/143 06310-01 34
70/154 06310-02 36
75/165 06310-02 36
80/176 06310-03 38
85/187 06310-03 38
90/198 06310-04 40
95/209 06310-04 40
100/220 06310-05 42
105/231 06310-06 44
110/242 06310-07 46
115/253 06310-08 48
*Rider’s weight: Rider wearing proper
riding gear.
Make sure you know your total
weight with riding gear. Riding gear
weighs between 5 and 15 kg.
Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
Part no. MI_
KT 1892/93/94
Issued 2017-09-22
KT 1894: KTM 450 SX-F & Husqvarna
TC 450
Rider’s weight*
kg/pounds
Spring
part no
Spring rate
N/mm
60/132 06310-05 42
65/143 06310-05 42
70/154 06310-06 44
75/165 06310-06 44
80/176 06310-07 46
85/187 06310-07 46
90/198 06310-08 48
95/209 06310-08 48
100/220 06310-09 50
105/231 06310-10 52
110/242 06310-11 54
115/253 06310-12 56
*Rider’s weight: Rider wearing proper
riding gear.
Make sure you know your total
weight with riding gear. Riding gear
weighs between 5 and 15 kg.
-
1
-
2
-
3
-
4
-
5
-
6
Ohlins KT1892 Mounting Instruction
- Type
- Mounting Instruction
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ohlins HO1594 Mounting Instruction
-
-
Ohlins BA1784 Mounting Instruction
-
-
-
-
-
-
-