Jlab Audio Omni Owner's manual

Jlab Audio
Brand
Jlab Audio
Model
Omni
Category
Bluetooth music receivers
Type
Owner's manual
CHARGING Note: For optimum performance, charge overnight with Micro USB cable prior to using.
Connect the Micro USB cable to the headphone’s left earcup input and connect the USB into a computer
or AC adaptor (not included). Make sure the USB connection has a power output source.
Solid red light indicates Omni is charging.
Solid white light indicates Omni is fully charged.
Full charge is between 1.5-2 hours.
Notes:
• For Bluetooth to work with your device, make sure the AUX switch is on AUX OUT. Omni will search and connect to the last Bluetooth
device it was connected to when turned on.
• Omni can be connected to 2 devices at one time but cannot play simultaneously. To reset the Bluetooth connection with a new device,
follow the Bluetooth pairing steps. To unpair, select forget JLab Omni on your device in your Bluetooth settings.
• If for any reason Bluetooth connection is lost, manually reconnect your Bluetooth device.
OMNI WIRELESS
HEADPHONES
We love that you are rocking JLab Audio!
We take pride in our products and fully stand behind them.
S
A
T
I
S
F
A
C
T
I
O
N
G
U
A
R
A
N
T
E
E
30
DAY
C
U
S
T
O
M
E
R
S
U
P
P
O
R
T
U
.
S
.
B
A
S
E
D
YOUR SATISFACTION IS GUARANTEED
You may exchange or return merchandise within 30 days of the purchase date.
Learn more at jlabaudio.com/guarantee
YOUR WARRANTY
You may register your product at jlabaudio.com/register. All warranty claims are subject to JLab Audio
authorization and at our sole discretion. Retain your proof of purchase to ensure warranty coverage.
CONTACT US
Reach out to us at [email protected] or visit jlabaudio.com/contact
L
I
M
I
T
E
D
O
N
E
Y
E
A
R
W
A
R
R
A
N
T
Y
FIRST TIME SETUP: BLUETOOTH PAIRING
Select “JLab Omni” in your device settings
to connect.
When the headphones
are paired, voice prompts
“Omni paired to device” and
white light blinks slowly.
Bluetooth
JLab Omni
Settings
3
When the Omni Headphones are
powered off, press and hold the center
button for approximately 10 seconds.
The power will first turn on with a
blinking white light and voice
“JLab Omni on” followed by blue and
white blinking lights and voice
“Waiting for device to connect”.
2
Turn on the Bluetooth
in your device settings.
Bluetooth
Settings
1
ACCESSORIES
TRAVEL
CASE
MICRO USB
CABLE
MICRO USB
INPUT
AUX
CABLE
OR
Charging Fully charged
POWER ON:
Press and hold center button for 3 seconds.
Voice prompt “JLab Omni on” and white
light blinks slowly.
POWER OFF:
Press and hold center button for 3 seconds.
Voice prompt “power off” and lights turn off.
PLAY / PAUSE / ANSWER / HANG UPv:
Press center button once.
*SIRI FOR APPLE DEVICES:
Press and hold for 2 seconds.
TRACK FORWARD:
Quickly turn and release wheel clockwise.
TRACK BACKWARD:
Quickly turn and release wheel counterclockwise.
VOLUME UP:
Turn and hold wheel clockwise.
VOLUME DOWN:
Turn and hold wheel counterclockwise.
*Siri is a registered trademark of Apple Inc. and is no way affiliated with this promotion.
JLABAUDIO.COM
BUTTON FUNCTIONS
AUX OUT FUNCTIONS
AUX IN FUNCTION
SHARE YOUR MUSIC
Connect another headphone or earbud into
the Omni AUX port to share the same content
from your Bluetooth device. The Omni will
power both devices and the button functions
will work alongside both headphones.
Connect the AUX cable to the Omni AUX port and your device to use as a
non-Bluetooth headphone. Omni does not need to be turned on for AUX
INPUT function.
Note: The Omni button functions will not function while in AUX INPUT
mode. Functions will be controlled solely from your device.
BLUETOOTH RECEIVER
Using the AUX cable, the Omni can plug into a
receiver or stereo input and turn the device into a
Bluetooth receiver. Make sure to adjust the volume
on the Omni and your input device accordingly.
CAUTIONS
• Avoid getting moisture or liquids on the headphone cups.
• Avoid extreme heat, cold, and humidity.
• Avoid dropping or crushing headphones, stressing the cable by
rapid pulling or extreme force, or bending the cable at a sharp
angle.
• Wax may build up in headphone cups, lowering the sound quality.
Carefully remove the wax with a cotton swab or other small tool to
improve the sound quality.
• If you experience discomfort or pain, try lowering the volume
or discontinuing use temporarily.
• If you experience regular discomfort while using this product,
discontinue use and consult your physician.
• We recommend you treat your headphones as you would a nice
pair of sunglasses and keep them in safe location when not in use.
WARM-UP YOUR HEADPHONES
Optional: Burn-in is the process for exercising new audio equipment. We recommend 40 hours of burn-in time for most headphones to reach
optimal performance. The main purpose of the process is to loosen the diaphragm of a newly crafted headphone and to stress the headphone
driver. Normal, everyday use can also burn-in the headphones though JLab’s proprietary burn-in provides an ideal mix of sounds and
frequency sweeps to achieve this.
Burn-in your audio equipment with the JLab Audio app available on the App Store and Google Play.
Or access the burn-in method at: jlabaudio.com/burnin
AUX IN
MIC
AUX OUT
AUX INAUX OUT
MIC
  • Page 1 1
  • Page 2 2

Jlab Audio Omni Owner's manual

Jlab Audio
Brand
Jlab Audio
Model
Omni
Category
Bluetooth music receivers
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents