Contec CONPROSYS HMI System (CHS) Owner's manual

First Step Guide

CONTENTS

HMI/SCADA software

CONPROSYS HMI

System

Introduction .................................................................. 4

Safety Precautions ...................................................... 9

Configuration of the Monitoring Project......... 13

Registration and Settings of the Device .......... 16

Creation of the Monitoring Page ....................... 31

Run and Display the Monitoring Page ............. 43

Help and Inquiries .................................................... 47

Index .............................................................................. 50

— 2 —

Table of Contents

Introduction ....................................................................... 4

1. Procedure until ready to use .............................................................................................................................. 5

2. Related Manuals ...................................................................................................................................................... 6

3. About the Software ................................................................................................................................................ 7

4. Operation Environment ........................................................................................................................................ 8

1. Development Environment .......................................................................................................................... 8

2. Monitoring Environment ............................................................................................................................... 8

Safety Precautions ............................................................. 9

1. Safety Information............................................................................................................................................... 10

2. Handling Precautions ......................................................................................................................................... 11

3. Security Warning .................................................................................................................................................. 12

1. Information security risks ........................................................................................................................... 12

2. Security measures – e.g. ............................................................................................................................. 12

Configuration of the Monitoring Project ..................... 13

1. Log In to the Project Admin Account .......................................................................................................... 14

2. Create Project ........................................................................................................................................................ 15

Registration and Settings of the Device ....................... 16

1. Add Device ............................................................................................................................................................. 17

2. Add Device User ................................................................................................................................................... 19

3. Configure the Device ......................................................................................................................................... 20

4. Set Tag ...................................................................................................................................................................... 27

5. Logger Setting and Alarm Setting ................................................................................................................ 30

Creation of the Monitoring Page ................................... 31

1. Add Page ................................................................................................................................................................. 32

2. Edit Page ................................................................................................................................................................. 33

3. Basic Operation for a Monitoring Page ...................................................................................................... 34

1. Place a Control ............................................................................................................................................... 34

2. Configure the Properties of Control ...................................................................................................... 34

3. Align the Position or Adjust the Size of Control ............................................................................... 35

4. Set the Page Size ........................................................................................................................................... 36

5. JavaScript.......................................................................................................................................................... 36

6. Save the Created Page ................................................................................................................................ 36

4. Link Control Property and Device Tag (Variables)................................................................................... 37

5. Input and Output Data to the Device .......................................................................................................... 39

1. Output Data to the Device ........................................................................................................................ 39

2. Input Data from the Device ...................................................................................................................... 39

— 3 —

Table of Contents

6. Input and Output Data Between the Controls ......................................................................................... 40

1. Output Data .................................................................................................................................................... 40

2. Input Data ........................................................................................................................................................ 40

7. Configure the Property for Multiple Controls and Link Them Simultaneously........................... 41

1. Paste Multiple Controls .............................................................................................................................. 41

2. Configure the Property for Multiple Controls and Link Them Simultaneously .................... 42

Run and Display the Monitoring Page .......................... 43

1. Start up as a Home Page of the Project User ........................................................................................... 44

2. Run the Page from Dashboard ....................................................................................................................... 45

3. Specify URL on the Browser to Display the Monitoring Page ........................................................... 46

Help and Inquiries ........................................................... 47

1. How to Use Online Help ................................................................................................................................... 48

1. Start up Online Help .................................................................................................................................... 48

2. Table of Contents of Online Help ........................................................................................................... 48

2. Inquiries ................................................................................................................................................................... 49

Index .................................................................................. 50

— 4 —

Introduction

This section provides necessary information of the software

such as the outline and manuals before actual use.

—

Introduction

—

CONPROSYS HMI System First Step Guide

— 5 —

1. Procedure until ready to use

The following chat shows the standard procedure until the product is ready to use.

Installation of CONPROSYS HMI System

Refer to

the Installation Guide

Configuration of the Monitoring Project

Refer to

page 13

Registration of the Device

Refer to

page 16

Connecting the Device to the Network

Refer to the Reference Manual

(Software).

(

When using the CONPROSYS Device

Series only)

Configuration of the CONPROSYS Device

Refer to

page 20

Configuration of the MQTT Device

Refer to

page 25

Creation of the Monitoring Page

Refer to

page 31

*This procedure can be different depending on the user's environment or system types.

—

Introduction

—

CONPROSYS HMI System First Step Guide

— 6 —

2. Related Manuals

The manuals related to this software are listed below.

Read them as necessary along with this document.

 Must Read the Followings.

Name

Purpose

Contents

How to get

Installation Guide

Read this when

installing this software.

This describes the installation

procedure of this software.

Download from

the Contec

website (PDF)

First Step Guide

(This document)

Read this when

operating this software.

This describes the device

registration and configuration,

or monitoring page creation

and more.

Download from

the Contec

website (PDF)

CONPROSYS Device

Series Reference

Manual (Software)

Read this when setting

up the "CONPROSYS

WEB Setting"

This describes how to set each

function of the "CONPROSYS

WEB Setting".

Download from

the Contec

website (PDF)

 Download Manuals

Download the manuals accordingly from the following URL.

Download

https://www.contec.com/download/

—

Introduction

—

CONPROSYS HMI System First Step Guide

— 7 —

3. About the Software

This guide describes the first step on how to run the software after installing the CONPROSYS HMI

System.

As for an installation procedure of the CONPROSYS HMI System, refer to the "CONPROSYS HMI

System Installation Guide".

The "CHS" is used as an abbreviated form of the "CONPROSYS HMI System" in some sections in this

guide.

—

Introduction

—

CONPROSYS HMI System First Step Guide

— 8 —

4. Operation Environment

1. Development Environment

Configure the system through the browser. The verified environments are listed below.

 PC

Google Chrome 47 and later versions.

Mozilla Firefox 42 and later versions.

2. Monitoring Environment

Remote-monitor through the browser. The verified environments are listed below.

 PC

Google Chrome 47 and later versions.

Mozilla Firefox 42 and later versions.

 Android

Google Chrome 47 and later versions.

Mozilla Firefox 42 and later versions.

 iOS

Safari 8 and later versions.

Google Chrome 47 and later versions.

— 9 —

Safety Precautions

Understand the following definitions and precautions to

use the software safely.

Never fail to read them before using the software.

—

Safety Precautions

—

CONPROSYS HMI System First Step Guide

— 10 —

1. Safety Information

This document provides safety information using the following symbols to prevent accidents

resulting in injury or death and the destruction of equipment and resources.

Understand the meanings of these labels to operate the equipment safely.

DANGER

Signal word used to indicate an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

WARNING

Signal word used to indicate a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION

Signal word used to indicate a potentially hazardous situation which,

if not avoided, could result in minor or moderate injury.

—

Safety Precautions

—

CONPROSYS HMI System First Step Guide

— 11 —

2. Handling Precautions

CAUTION

 The specifications of the software are subject to change without notice for enhancement and

quality improvement. Even when using the software continuously, be sure to read the manual

in the CONTEC's website and understand the contents.

 Do not modify the software.

CONTEC will bear no responsibility for any problems, etc., resulting from modifying the

software.

 Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that

may appear in this document or for results obtained by the user as a result of using the

software.

—

Safety Precautions

—

CONPROSYS HMI System First Step Guide

— 12 —

3. Security Warning

When connecting to the network, be aware of security-related problems. See the examples of

Security measures below and set up the product properly along with the network devices.

1. Information security risks

 Unauthorized access from the outside through a network could cause the system halt, data

damage, or exposure to malware. *1

 Invaded and used as a stepping stone, a device might attack the others through networks. (a

victim becomes an assailant)

 Information might leak without realizing due to the connection to the network.

 Secondary damages such as harmful rumors, liability in damages, social credibility fall, and

opportunity loss are expected led by the troubles described above.

*1: Malware (Malicious Software) is software that brings harm to a computer system and performs

unintended operations.

2. Security measures – e.g.

 Do not keep using the default password. (Refer to the product manual for the password setting).

 Set a strong password.

Combined with upper and lowercase letters, and numbers so that it cannot be easily

analogized by others.

 Change the password periodically.

 Disable unnecessary network services and functions.

 Restrict access to the network with network devices. *2

 Restrict ports to be released on the network with network devices. *2

 Create a closed network connection using such as dedicated network or VPN*3

*2: Inquire for setting procedure to manufacturers.

*3: VPN (Virtual Private Network) a secured network that wards off unauthorized access by

protecting the communication path with authentication and encryption.

Unfortunately, there are no perfect ways to avert unauthorized access or close a security hole

that are endlessly found day and night.

Please understand that risks are always involved with the Internet connection, and we strongly

recommend a user should constantly update information security measures.

— 13 —

Configuration of the

Monitoring Project

This section describes how to configure the monitoring

project.

—

Configuration of the Monitoring Project

—

CONPROSYS HMI System First Step Guide

— 14 —

1. Log In to the Project Admin Account

Enter the following URL in a browser address bar (Chrome or Firefox) to open the login dialog box.

Login URL : http://chs_server/

(It is an IP or a domain name of the server that installed chs_server:CHS)

Enter the following information in the dialog box, then, log in.

Defaults

Project ID : admin

Login ID : admin

Password : admin

CAUTION

Change a login ID and a password to your own from the displayed defaults.

After logging in, change the user password on the User screen.

When logging in has succeeded, Development Environment appears.

The list of the Project is initially displayed on the screen.

—

Configuration of the Monitoring Project

—

CONPROSYS HMI System First Step Guide

— 15 —

2. Create Project

Click the [Add Project] to create a new Project.

The Project Setting screen opens. Enter the information of the Project.

After entering the details, click the [Save and Exit].

Click the [Login Project] button in the newly created Project, and enter the following information

in the dialog box, then, log in.

Project ID : (Created Project ID)

Login ID : admin

Password : admin

CAUTION

Change login ID and password to your own from the displayed defaults.

After logging in, change the user password on the User screen.

When logging in has succeeded, Development Environment of the Project appears.

The page (screen) list of the project is initially displayed on the screen.

— 16 —

Registration and Settings

of the Device

The device needs to be registered in CHS for

communicating with CHS Project.

This section describes a device registration and the setting

procedure.

—

Registration and Settings of the Device

—

CONPROSYS HMI System First Step Guide

— 17 —

1. Add Device

Log in to the created project.

Click the [Device] menu and open the device list.

When linking to any device of the CONPROSYS series, click the [Add CONPROSYS Device] to add the

device.

When linking to any device that supports MQTT protocol, click the [Add MQTT Device] to add the

device.

Enter the device ID, the device name, and the serial number. Click the [Save] button to complete the

Add Device.

 Serial Number

When using the CONPROSYS series device, the serial number can be found on the back or the side

of the controller. Also, the number can be checked on the [CONPROSYS Web Setting] screen through

the browser. Go to the [Status] menu –[System] and see [Serial Number].

When using the device that supports MQTT protocol, a unique string that is not used by any other

strings within the Project must be set for the serial number.

Label of the CONPROSYS series device

(As for the Integrated type, the number can be found on the back of the controller.

As for the Configurable type, it can be found on the side of the controller.)

—

Registration and Settings of the Device

—

CONPROSYS HMI System First Step Guide

— 18 —

Browser Screen

—

Registration and Settings of the Device

—

CONPROSYS HMI System First Step Guide

— 19 —

2. Add Device User

In order to send or receive data, the CONPROSYS device needs to be authenticated from CHS.

For authentication, make the device act like a user to log in. It is necessary to add the user in the CHS

Project to log in. User types of the device that can be logged in CHS are the [Device] or the

[Administrator] from the User Privilege.

Click the [User] menu and perform the [Add User].

Enter the login ID, password, and other necessary items, then select Device (or Administrator) from

User Privilege.

Click the [Save] or the [Save and Exit] to save the settings.

—

Registration and Settings of the Device

—

CONPROSYS HMI System First Step Guide

— 20 —

3. Configure the Device

 The CONPROSYS series device

1 Connect LAN cable to the registered CONPROSYS device and configure the settings by

accessing through browser.

The factory settings of the CONPROSYS are listed below.

Access the device from a PC on the same network that the CONPROSYS is connected.

Enter user name and password, then log in.

Item

Setting

IP Address

10.1.1.101

Subnet Mask

255.0.0.0

Access URL

http://10.1.1.101

User Name

mc341

Password

mc341

CAUTION

Updating the firmware is necessary if your CONPROSYS device has an older version than the

following ones. Visit the CONTEC website and download the latest version. For the firmware details,

refer to the Reference Manual (Software) of your controller.

Series

Version

M2M Controller Serials Integrated Type

3.5.0

M2M Controller Serials Configurable Type

3.6.0

M2M Gateway Serials

3.5.0

Download

https://www.contec.com/download/

Page is loading ...

Contec CONPROSYS HMI System (CHS) Owner's manual

This manual is also suitable for

Contec CONPROSYS HMI System (CHS) Owner's manual

Related papers

Other documents