KYOCERA ECOSYS PA6000x User guide

KYOCERA
Brand
KYOCERA
Model
ECOSYS PA6000x
Type
User guide
2022.5 3VC0T5611001
Pull the Cassette 1 completely out
of the machine.
1
2
1
22
1
123
2Adjust the paper length and width guide to the
paper size required.
Fan the paper, then tap
it on a level surface.
3
Load paper.
4Gently push the Cassette 1 back in.
5
Step 3 Loading Paper
+ Set print side face-up.
+ No bent or folder edges in the paper.
Such paper may cause paper jams.
+ Set the quantity of the paper less than
the maximum paper indication on the
side or the cassette.
+ If the paper is loaded without adj
usting the paper length guide and the pa
per width guides, skewed paper feeding,
and a paper jam will occur.
Step 2 Install Waste toner box
4
3
2
1
Open the top cover. After Removing the packing material,
shake and install the toner container. Close the top cover.
3
12
34
567
89
(for inch models)
Open the Box. Remove the machine carefully from the box
grasping both sides.
Lift the main unit from the handles by cardboard handles.
Step 1 Setting up the Printer
1
2
Recommended Installation Space
*1: The value when an optional rear tray (PT-320) is installed to the the ECOSYS PA5000x,
ECOSYS PA5500x and ECOSYS PA6000.
100 mm
(3.94")
300 mm
(11.81")
400 mm
(15.75")
400 mm
(15.75")
500 mm (19.69")
200 mm (7.87")
500 mm (19.69") *1
Installation Environment
Kyocera Recommends selecting the Location for the printer as follows:
1. Room Temperature range: 50 to 90.5°F
2. Humidity Level: 10 to 80%
3. Power:
Avoid the following locations when selecting a site for the machine.
Adverse environmental conditions may affect the image quality.
+ Avoid locations near a window or with exposure to direct sunlight.
+ Avoid locations with vibrations.
+ Avoid locations with rapid temperature fluctuations.
+ Avoid locations with direct exposure to hot or cold air.
+ Avoid poorly ventilated locations.
3VC0T5611001
Setup GuideECOSYS PA6000x / ECOSYS PA5500x
ECOSYS PA5000x / ECOSYS PA4500x
A dedicated 120VAC 60Hz 15A outlet
A dedicated 200-240VAC 50/60Hz 15A outlet
120 V Specification Model:
230 V Specification Model:
Step 7 Installing Software
Access the following URL and select your model and OS.
Download Center: https://kyocera.info/
For Windows
Download and run the Web Installer and follow the
on-screen instructions to install the driver and software.
For Mac
Download and run the driver and follow the on-screen
instructions to install.
Report Print:
Exit
Menu Map
Yes No
2
01
03
Print.
Are you sure?
Status Page
[▲] [▼] key > [Status Page] > [OK] key > [Yes]
1
2
Status Page
Config. List
02
Menu:
03
02
01
Report:
Report Print
Exit
01
Job Log History
02
1
Report
USB Drive
Counter
Exit
[Menu] key > [▲] [▼] key > [Report] >
[OK] key > [▲] [▼] key > [Report Print] > [OK] key
1
2
1
2
Step 6 Printing a Status Page
Step 4 Powering on the Printer
2
1
Turn the power switch ON at the front of the printer.
2
Connect the power cord to the rear of the machine and the
other end to the power outlet.
1
NOTE
Prepare the device and
information according to
the your environment.
For details of the network
settings, refer to the
Operation Guide.
6When the following screen
appears, select [Finish].
Completing Setup
Please read the [Read
me] to make more
detail settings.
Readme Finish
5Select [Change] when you set whether
notify low toner via panel or not.
If you set it later, select [Skip].
Skip
Setup (3/3)
Set whether norify
low toner via
Paner or not.
Change
Skip
Setup (1/3)
Set the time zone,
date and time.
Change
Select [Change] when you
change the time zone, date
and time. Follow the instruc
tions on the screen. If not,
select [Skip].
3
The setup screen appears.
2Select [Yes].
Welcom.
Set up your machine
now.
Are your sure?
Yes No
1
Language:
English
01
Deutsch
02
Français
03
*
Press [ ] [ ] key to select
default language > [OK] key.
Step 5 Default Settings of the Machine
The screen moves to the
next step.
4
The screen moves to the next
setp.
Select [Change] when you
set the IP address to use
the machine on the network.
Follow the instructions on the
screen. If you set it later,
select [Skip].
Skip
Setup (2/3)
Set the IP address to
enable the machine to
run on your network.
Change
  • Page 1 1
  • Page 2 2

KYOCERA ECOSYS PA6000x User guide

KYOCERA
Brand
KYOCERA
Model
ECOSYS PA6000x
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents