Balance
Ceiling Lamp
Accord Balance Ceiling Lamp 5104
Natural Wood Veneer, MDF and Carbon Steel.
B B
C C
D D
E E
F F
G G
J J
K K
L L
P P
R R
T T
2
4
2
4
2
3
2
3
2
2
2
2
2
1
2
1
2
0
2
0
1
9
1
9
1
8
1
8
1
7
1
7
1
6
1
6
1
5
1
5
1
4
1
4
1
3
1
3
1
2
1
2
1
1
1
1
1
0
1
0
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DES
EN.
VER
IF.
APRO
V.
MAN
UF.
QUAL
ID
SE NÃO
ESPECIFICADO:
DIMENSÕES EM
MILÍMETROS
ACABAM.
SUPERFÍCIE:
TOLERÂNC
IAS:
LINE
AR:
ANGUL
AR:
ACABAME
NTO:
REBARBA
R E
QUEBR
AR
AREST
AS
AGUD
AS
NO
ME
ASSINAT
URA
DA
TA
MATERI
AL:
NÃO MUDAR ESCALA DO
DESENHO
REVIS
ÃO
TÍTU
LO:
DES.
Nº
ESCALA:
1:20
FOLHA 1
DE 1
A
0
PES
O:
MONTAGEM
1447
4
5
Read carefully all the Assembly Instructions below, before
starting the installation process.
Notice that the fixture is packed pre-assembled. Remove the
protecting package from the pieces taking care to not harm
any parts with cutting surfaces or objects. Lay the parts of the
fixture on some horizontal surface in order to assemble them,
if needed use the protecting package to soften the surface and
protect the parts from getting scratched or harmed.
Once the protecting packages are removed, rotate the
metallic arms of the fixture until it is alligned according with
the image (2) or according to the desired position.
After all the metallic arms are positioned in the desired
allignment, one of a time, hold the stem in place and screw
the nut located on top of the canopy until it is locked. Take
care to not harm the energy cables and connectors in this
process.
On each metallic arm, join the dome to the metallic support
through it’s upper opening, alligning the holes and fastening
the provided screws (S01) to lock the dome in place.
Finish the fastening of the crosstip screws located on the
swivel joints base, in order to keep it tight.
Before starting the mounting of the fixture on the ceiling,
holding the canopy in place, rotate the metallic arms one last
time to make sure its completely tight and locked on it’s
position.
1
3
2
4
5
12
3
6
5104
E26
Balance
Ceiling Lamp
Accord Balance Ceiling Lamp 5104
Natural Wood Veneer, MDF and Carbon Steel.
B B
C C
D D
E E
F F
G G
J J
K K
L L
P P
R R
T T
2
4
2
4
2
3
2
3
2
2
2
2
2
1
2
1
2
0
2
0
1
9
1
9
1
8
1
8
1
7
1
7
1
6
1
6
1
5
1
5
1
4
1
4
1
3
1
3
1
2
1
2
1
1
1
1
1
0
1
0
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DES
EN.
VER
IF.
APRO
V.
MAN
UF.
QUAL
ID
SE NÃO
ESPECIFICADO:
DIMENSÕES EM
MILÍMETROS
ACABAM.
SUPERFÍCIE:
TOLERÂNC
IAS:
LINE
AR:
ANGUL
AR:
ACABAME
NTO:
REBARBA
R E
QUEBR
AR
AREST
AS
AGUD
AS
NO
ME
ASSINAT
URA
DA
TA
MATERI
AL:
NÃO MUDAR ESCALA DO
DESENHO
REVIS
ÃO
TÍTU
LO:
DES.
Nº
ESCALA:
1:20
FOLHA 1
DE 1
A
0
PES
O:
MONTAGEM
1447
7
10
12
13
11
Once the overall structure of the fixture is assembled, the
ceiling must me prepared to mount the fixture.
Start removing the locking screws (S03) from the canopy.
Low the outter canopy from the structural base in order to
have some space to work.
Place the fixture in the desired position and make the marks
on the ceiling, then drill the holes and insert the plastic
bushings.
Pass the energy cable through the junction box cover, rise the
fixture close to the junction box and make the electrical
connections following all the applicable local codes. Insert
the escess energy cable inside the junction box.
Fasten the provided screws (S11) on the junction box cover
in order to assemble it to the junction box.
Fasten the provided screws (S07) on the structural base,
attaching the fixture to the ceiling. Take care to not press or
harm the energy cable.
Rise the outter canopy and lock it at the structural base with
the locking screws (S03).
Turn on energy power, the luminaire is ready for use.
8
9
7
8
9
10
11
12
13
The wooden dome which houses the light source is
articulated. Hold the dome and rotate it in order to direct the
light to the desired spot. Be careful to not exceed the swivel
joint’s articulation limit so it doesn’t break.
It is recommended to use a mini LED bulb (E26 - A15) in this
fixture. Due to the dome size a regular bulb size would come
out of the dome causing excessive light glare.
USER GUIDE
S01(12)
S03(2)
S07(6)
PROVIDED SCREWS
S11(2)
5104
E26
/
