viewneo VN-BTLR-01 User guide

  • Hello! I've read the viewneo Butler Quick Start Guide and I'm ready to answer your questions about setting up the device and its features, such as creating a hotspot and using the setup assistant. How can I help you today?
  • How do I connect the Butler?
    What is the name of the hotspot that Butler creates?
    What address do I use to access the hotspot wizard?
Butler
Quick Start Guide
Slots and accessoires Anschlüsse und Zubehör
EN DE
1. Antenna
2. Ethernet
1. ADD BUTLER IN THE CMS
Go to devices and add Butler in your
viewneo account.
2. CONNECT BUTLER
Connect Butler with the power supply and
if needed, the LAN cable. Wait unl the blue
light
appears to indicate that it is successfully connected.
3. SETUP HOTSPOT
The Butler will automacally create a hotspot:
viewneo_butler_. Use your cell phone/PC to
connect to the hotspot and then go to:
hp://192.168.2.5
4. SETUP ASSISTANT
Follow the instrucons on your screen to com-
plete the setup process.
1. BUTLER IM CMS ANLEGEN
Butler im viewneo Account unter der Rubrik
„Geräte“ hinzufügen.
2. BUTLER ANSCHLIESSEN
Butler an die Stromversorgung anschließen
und bei Bedarf LAN Kabel verbinden.
Warten bis Butler blau leuchtet.
3. HOTSPOT VERBINDEN
Der Butler erstellt einen Hotspot:
viewneo_butler_ Über Handy/PC verbinden
und folgende Adresse im Browser aufrufen:
hp://192.168.2.5
4. SETUP ASSISTENT
Folge nun den Anweisungen auf dem Bildschirm,
um die Einrichtung vollständig abzuschließen.
EN DE
Setup Einrichtung
UNIVERSAL AC
ADAPTOR
2x ANTENNAS
3. Power
4. Reset
FCC Warning
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any inte
rference received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interferenceto radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for
help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator and your body.
HELP AND SUPPORT
Need help with viewneo® Cloud or
viewneo® hardware? Find detailed
informaon, FAQs, tutorials and
downloads at support.viewneo.com.
HILFE UND SUPPORT
Du brauchst Hilfe mit viewneo® Cloud
oder viewneo® Hardware?
Auf support.viewneo.com ndest du
Infos, FAQs, Tutorials und Downloads.
© 2019 viewneo®
viewneo® is a trademark of Adversign Media GmbH
www.viewneo.com
/