JCP35WA-A
Long Distance
Wireless Charger
JCP35WA-A
DC22V-40V
DC24V/1.5A
DC5.5*2.1
MAX 5V2A
13mm-28mm
≤1W
>50% @25mm，5W Load，24V Input
0℃-35℃
Model:
Voltage Range: Rated
Voltage/Current: Input Plug
type:
Output Plug type:
Output TypeA+TypeC:
Wireless Charge Distance:
Standby Power Consumption:
Efficiency:
work Temperature:
Protection Character:Input Coil OCP,OTP,OVP,UVLO,FOD
TYPEA+TYPEC
Red/Green indicator light
Installation Surface
Output USBC
Output USBA
DC Input (DC5.5*2.1)
13~28mm
2-5
125
125
ST4.2*16
20
Installation Direction
The Packing Include:
Wireless Charging Power Station
User Marnual
X1
X1
Table Stick(optionally available)X1
Installation screw pack X1
13~28mm
Charge Status Indicator
Charger
Status
Red LED
Green LED
Power On Standby Charging Fault
ON ON OFF OFF
OFF ON
Blink(1Hz)
1 time Blink(1Hz)
Note：
Abnormal conditions include:the receiving end is placed too far,
the PCBA temperature is too high,metal foreign objects enter,
the input current is overcurrent,and the input voltage is
overvoltage,etc.
Certification
Avoid placing any metal on the heating surface during working.
Avoid placing magnetic stripe card on the heating surface which
can easily damage the card.
Make sure that the thickness of the upper desktop is within the
range of the specification,otherwise it will not be able to
charge.
Avoid humidity, liquid, fire and high temperature as it may cause
hazard to users.
Do not try to disassemble or modify the product.
Do not attempt to disassemble to avoid fire hazard or short
circuit.
Any of damage by abnormal use of product will void the manuf
acture warranty.
Do not use product when the cord is damp, damaged or,loose
as it may cause short circuitand overheat.
Do not bend the power cord.
Do not handle the power cord with wet hands or pull the built-in
cable.
Contact with overheated equipment may cause discoloration or
surface damage.
Keep to other electrical devices such as Microwaves, sufficient
distance.
Make sure that the table stick must be affixed directly above
the Wireless Charger.
FCC Statement：
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)1) This device may not cause harmful interference,and (2) this device must accept any interfere
received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment .This equipment should be installed and operated with minimum distance 20cm between
the radiator& your body.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However,there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
(1)1) l'appareil ne doit pas produire de brouillage,
(2)2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouill
est susceptible d'en compromettre le fonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation
et mise en œuvre de ce matériel devrait avec échangeur distance minimale entre 20 cm ton
corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.
/