CURT 13414 Installation guide

CURT
Brand
CURT
Model
13414
Type
Installation guide

CURT 13414 is a weight-carrying and weight-distribution hitch designed for the Jeep Commander (excluding the Rocky Mountain Edition). It has a gross load capacity of 5,000 lbs. for weight carrying and 7,500 lbs. for weight distribution, with a tongue weight capacity of 500 lbs. for weight carrying and 750 lbs. for weight distribution. This hitch is easy to install with no drilling required and comes with a limited lifetime warranty.

CURT 13414 is a weight-carrying and weight-distribution hitch designed for the Jeep Commander (excluding the Rocky Mountain Edition). It has a gross load capacity of 5,000 lbs. for weight carrying and 7,500 lbs. for weight distribution, with a tongue weight capacity of 500 lbs. for weight carrying and 750 lbs. for weight distribution. This hitch is easy to install with no drilling required and comes with a limited lifetime warranty.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
5,000 500
7,500
750
JEEP COMMANDER EXCLUDING ROCKY MOUNTAIN EDITION
4/1/2010
13414
60
17
30
HITCH WEIGHT:
LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
757414
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HEX BOLT1_2 - 13 x 441
CONICAL TOOTHED WASHER1/2"
4
2
If vehicle is equipped with an OEM Tow Hook: Remove permanently for hitch installation. Install time will increase
from 30 to 90 minutes.
1. Lower spare tire to allow access to the rear bumper support.
2. Remove (6) plastic fasteners from bumper fascia tabs. (Reuse later)
3. Gently pull bumper cover away from vehicle and raise hitch into position. Secure hitch with hex bolts and conical
washers through existing holes in bumper support.
4. Torque all 1/2" fasteners to 75 lb-ft.
5. Reinstall plastic push fasteners and bumper cover removed in step 2.
6. Raise spare tire back into position.
- NO DRILLING REQUIRED
- LOWER SPARE TIRE
BUMPER SUPPORT
EXISTING HOLES
1
2
  • Page 1 1

CURT 13414 Installation guide

CURT
Brand
CURT
Model
13414
Type
Installation guide

CURT 13414 is a weight-carrying and weight-distribution hitch designed for the Jeep Commander (excluding the Rocky Mountain Edition). It has a gross load capacity of 5,000 lbs. for weight carrying and 7,500 lbs. for weight distribution, with a tongue weight capacity of 500 lbs. for weight carrying and 750 lbs. for weight distribution. This hitch is easy to install with no drilling required and comes with a limited lifetime warranty.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents