Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
INTRODUCTION
To get the best out of your new oil radiator, please read these
instructions carefully before using it for the first time.
We also recommend that you keep the instructions for future
reference, so that you can remind yourself of the functions of the
device.
IMPORTANT SAFETY MEASURES
- Read the instructions carefully before using the device for the
first time.
- The device may only be used in accordance with the
instructions in this manual.
- When unpacking the device, check that it has not been
damaged during transport.
- Do not immerse the device in any form of liquid.
- Remove the plug from the socket when cleaning, or when the
device is not in use.
- If the cord, plug or the device itself should become damaged,
do not attempt to repair the damage yourself, but instead take
it to a specialist for repair, as special tools are required.
- For indoor use only.
- Ensure that the cord does not come into contact with heat
sources such as hotplates, cookers, etc., as this may damage
the cord.
- The device must not be covered or built in.
OVERVIEW OF FUNCTIONS
1. Heating ribs
2. Thermostat button
3. Switches (1 and 2) with indicator lights
4. Cord rewind
5. Wheels
6. Mounting clamp
7. Wheel disc
8. Wing nuts
9. Carrying handle
FITTING WHEELS
- Turn the device upside down.
- Position the clamp and wheel disc
around the space between the first
and second rib.
- Put the wing nuts on and tighten
them.
- Screw the wheels firmly in place in
the outer holes on the wheel disc.
- Turn the device over so that it stands on its wheels.
- Wait 5 minutes before using the device.
USE
- Make sure the device is on a stable and level surface.
- Select the desired wattage using the 2 switches. There are 3
possible combinations - see below:
(5 ribs - 670-010):
Switch I the device runs on 500 W.
Switch II the device runs on 500 W.
Switches I + II the device runs on full wattage 1000 W.
(7 ribs - 670-011):
Switch I the device runs on 600 W.
Switch II the device runs on 900 W.
Switches I + II the device runs on full wattage 1500 W.
(9 ribs - 670-012):
Switch I the device runs on 800 W.
Switch II the device runs on 1200 W.
Switches I + II the device runs on full wattage 2000 W.
(11 ribs - 670-013):
Switch I the device runs on 800 W.
Switch II the device runs on 1200 W.
Switches I + II the device runs on full wattage 2000 W.
- Plug in. The device is now connected.
- Set the thermostat dial at the highest setting.
- Once the room temperature reaches the desired level, push
the thermostat down until the indicator light goes out.
- If you want to change the room temperature, push the
thermostat button up to raise the temperature or down to
lower it.
- When the device is switched on, the indicator light will be on
as long as the room temperature is lower than the temperature
set on the thermostat.
- After use, set both switches to 0 position and push the
thermostat down to the lowest point (smallest dot). Then
remove the plug from the socket.
CLEANING
Always unplug the radiator and let it cool before cleaning. Clean it
with a dry or damp cloth or using a weak soap solution where
necessary. Do not use abrasive cleaning agents.
10
UK
9
3
2
4
17 6
58
RYD_IM 09/07/04 9:39 Side 10
IMPORTANT
- Do not plug in the radiator until it is assembled.
- The radiator may only be used in an upright position.
- Do not scratch the fins with sharp tools as damage to the
enamel may lead to rust.
- The radiator needs a free airflow to maintain maximum
performance. Do not cover the openings.
- The external surfaces of the radiator are hot. Do not leave
children unattended close to the radiator.
ENVIRONMENTAL TIP
An electronic appliance should, when it is no longer capable of
functioning be disposed with least possible environmental
damage. The appliance should be disposed according to the local
regulations in your municipality, in most cases you can discharge
the appliance at your local recycling center.
THE WARRANTY DOES NOT COVER:
- If the above points have not been observed.
- If the appliance has not been properly maintained, if force has
been used against it or if it has been damaged in any other
way.
- Errors or faults owing to defects in the distribution system.
- If the appliance has been repaired or modified or changed in
any way or by any person not properly authorized.
Owing to our constant development of our products on both
functionality and design we reserve the right to change the
product without preceding notice.
IMPORTER:
Adexi Group
We take reservations for printing errors.
11
RYD_IM 09/07/04 9:39 Side 11
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
RYD_IM 09/07/04 9:39 Side 18
/
