![](//vs1.manuzoid.com/store/data-gzf/cfd631596b1d4a973c55c574acbb1878/2/000677836.htmlex.zip/bg1.jpg)
www.lg.com
KT-OPSU
ENG
Cards
Main Unit Screw (M3 x L6), 6 EA Power cord
한국어
카드류 본체 나사 (M3 x L6), 6 개 전원 코드
6
1
ENG
Place a soft cloth on the table and put the product with the screen facing downward.
Push KT-OPSU into the compartment to mount it.
한국어
테이블 위에 부드러운 천을 깔고, 화면이 아래쪽을 향하도록 세트를 올려 놓습니다.
KT-OPSU를 세트 뒷 면의 홈에 맞춘 후 밀어 올려 장착 합니다.
KT-OPSU
2
ENG
Attach KT-OPSU on the product using the four screws provided.
한국어
함께 제공된 나사 4개를 사용하여 세트에 고정시켜 줍니다.
KT-OPSU
P/NO : MBM65483601 (1608-REV01)
Printed in Korea
ENG
Please read this Easy Setup Guide carefully before operating your product. Keep it for future reference and record the model number and serial
number of the product. See the label attached on the product and quote this information to your dealer if you require service.
한국어
사용전에 ‘간편한 설치 안내’ 를 반드시 읽고 정확하게 사용하세요.
‘간편한 설치 안내’ 를 읽고 난 후에는 사용하는 사람이 언제나 볼 수 있는 장소에 반드시 보관하세요.
ACCESSORIES / 부속품 /
ENG
The accessories supplied with your product may vary depending on the model.
Product specications or contents in this Easy Setup Guide may be changed without prior notice due to upgrade of product functions.
Y-type cable may be provided instead of power cord depending on the country.
한국어
제품의 부속품은 모델에 따라 다르게 제공될 수 있습니다.
이 간편한 설치 안내에 나와 있는 제품 사양이나 내용물은 제품 기능 업그레이드에 따라 예고 없이 변경될 수 있습니다.
국가에 따라 전원 코드 대신 Y형 케이블이 제공될 수 있습니다.
Y
*MBM65483601*
WEIGHTS / 무게 /
ENG
1.7 kg
Product specications shown above may be changed without prior notice due to upgrade of product functions.
한국어
1.7 kg
위 제품 규격은 제품 기능의 개선을 위해 예고 없이 변경될 수 있습니다.
1.7
INSTALLING KT-OPSU / KT-OPSU 장착 방법 /
KT-OPSU
CAUTION /
주의 /
ENG
• Be careful of sharp edges on the rail and the handle.
• Attaching the product with non-standard screws may cause damage or the product to fall down.
LG Electronics is not liable for any accidents relating to the use of non-standard screws.
• Do not over tighten the screws as this may cause damage to the product and void your warranty.
• Attach KT-OPSU to the monitor before attaching OPS module to KT-OPSU. Otherwise, the screws may not be tightened.
한국어
• 레일과 핸들의 날카로운 부분에 다치지 않도록 주의하시기 바랍니다.
• 제품에 맞지 않는 나사로 고정할 시 제품 파손 및 제품이 떨어질 위험이 있습니다. 이에 대하여 당사가 책임을 지지 않습니다.
• 나사를 너무 꽉 조여 제품이 손상되면 품질 보증이 적용되지 않을 수 있습니다.
• OPS 모듈을 KT-OPSU에 먼저 장착할 경우 나사가 체결이 안될 수 있으니 KT-OPSU를 모니터에 우선 장착해 주십시오.
KT-OPSUOPSKT-OPSU
ENG
The illustrations in this Easy Setup Guide may differ from the actual product.
한국어
이 간편한 설치 안내의 그림은 실제 제품과 차이가 있을 수 있습니다.
Easy Setup Guide
간편한 설치 안내
ENG
ENGLISH
한국어
한국어
OPS Mounting Kit
3
1
2
ENG
Attach the OPS module to the KT-OPSU using the two screws.
ENG
Installation complete
한국어
나사 2개를 사용하여 OPS 모듈을 KT-OPSU에 조립합니다.
한국어
장착 작업 완료된 모습
KT-OPSUOPS