2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Computer cases
  6. Sharkoon
  7. SCORPIO 1000

Sharkoon SCORPIO 1000, SCORPIO 2000 Specification

  • Hello! I am an AI chatbot trained to assist you with the Sharkoon SCORPIO 1000 Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Manual
scorpio 1000/2000
Content
1. Features
2. Package contents
3. The case at a glance
4. Installing a mainboard
5. Installing a HDD
5.1 Fast Swap bays
5.2 3.5" HDD cage
5.3 3.5" drive bay
5.4 2.5" HDD cage
6. Installing a PSU
7. Installing an optical device
8. Installing an add-on card
9. The pre-installed fans
10. Installing additional fans / optimized airflow
10.1 Side panel
10.2 Top panel
Dear customer!
Congratulations for purchasing one premium quality SHARKOON
product.
For a long life time and to take full advantage of this product we
recommend that you read this manual completely.
Have a good time with our product!
SHARKOON Technologies
scorpio 1000/2000
1. Features
• ATXcase
• 4x5.25“drivebays(external)
• 2x3.5“fastswapdrivebays(external)
• 3x3.5“drivebays(internal)
• 4x2.5“drivebays(internal)
• TopI/Owith2xUSB2.0,1xeSATA,1xheadphoneand
1xmicrophoneconnector,powerandresetbutton
• 7slotsforadd-oncards
• Plasticfrontpanelwithairinlet,drivebaycoversinmeshdesign
• Quickfastenersforopticaldrives,mainboardmountingwith
installation opening for CPU coolers
• 2openingsforwatercooling
• Cablemanagementsystem
• Blackinteriorpainting
• Dimensions:508x210x503mm(LxWxH)
• Weight:~7.25kg
• FancongurationScorpio1000:
Case front
1x120mmLEDfan
(blue/pre-installed)
Side panel
1x200mmfanor2x120mmfans
(optional)
Backsideofcase
1x120mmfan
(pre-installed)
Top panel
2x120mmor2x140mmfans
(optional)
• FancongurationScorpio2000:
Case front
1x140mmLEDfanand1x80mmfan
(pre-installed)
Side panel
1x200mmfanor2x120mmfans
(optional)
Backsideofcase
1x120mmfan
(pre-installed)
Top panel
2x120mmor2x140mmfans
(optional)
scorpio 1000/2000
2. Package contents
• ATXcase“Scorpio1000”
(1x120mmfaninthecasefrontand
1x120mmfaninthecase’sbacksidepre-installed)
OR
• ATXcaseScorpio2000“
(1x140mmLEDand1x80mmfaninthecasefrontaswellas
1x120mmfaninthecase’sbacksidepre-installed)
• Accessorykit:
10xstand-offs
for mainboard
10xscrews
for drive/
mainboard
mounting
4xscrews
for HDD/PSU
mounting
10xscrews
with coarse
thread for HDD
mounting
12xscrews
withne
thread for HDD
mounting
4xfanscrews 4xmounting
rails
1xspeaker
Note:
If you are missing any of the items listed above, please contact
customer service via e-mail at [email protected] or call
+ 49 (0) 6403 – 775 6100.
3. The case at a glance
Front view Scorpio 1000
A – LEDs
B – 5.25"drivebays
C – 120mmLEDfan(blue/pre-installed)
D – Fast Swap drive bays
A
B
C
D
D
scorpio 1000/2000
Front view Scorpio 2000
A – LEDs
B – 5.25"drivebays
C – behindfrontbezel:
120mmLEDfan(blue/pre-installed)
D – FastSwapdrivebays(incl.pre-installed80mmfan)
Top view
A – Ventilation openings
B – TopI/O:
a – On/off button
b – Reset button
c – 2xUSB2.0connectors
d – 1xheadphonesandmicrophoneplug
e – 1xeSATAconnector
A
B
C
D
D
a
b
c
c
d
e
A
B
scorpio 1000/2000
Side view (closed/left)
A – Fanbrackets(1x200mmor2x120mmfan)
Side view (opened/left)
A – Drive bays for 5.25" devices
B – Mainboardmountingpanel
C – Installation opening for CPU coolers
D – Quickfastenersforopticaldrives
E – Mountingcagefor2.5“HDDs/SSDs
F – Mountingcagefor3,5“HDDs
G – Fast Swap drive bays
H – Cable openings
I – Circuitboardtoconnectthefrontfans(nofancontrol!):
a – Circuitboard’s4-pinpowerconnector
b – SATAdataconnectorHDD1(top)
c – SATAdataconnectorHDD2(bottom)
d – Fan power connectors
J – Mountingbayforasingle3.5"HDD
A
a
b
c
d
A
A
B
C
D
E
E
F
F
G
G
H
I
J
scorpio 1000/2000
Back view
A – Opening for I/O shield
B – Cableopenings(1xeSATA,2xwatercooling)
C – 120mmfan(pre-installed)
D – Slot bezels
E – PSUbracket
Bottom view
A – Case feet
B – Airintake(PSU)
The internal cables and connectors
A – Connectorsfor:
Reset Switch
HDD-LED
PowerLED+
PowerLED–
Power Switch
B – USBconnectoroftheUSBfronthub
C – Audioconnectors(HDAudioandAC’97)
D – eSATA connector
Note:
For more information on how to install the intended devices, refer
to their respective documents.
A
A
A
A
A
A
B
B
B
B
C
C
D
D
E
scorpio 1000/2000
4. Installing a mainboard
1. Openthecasebylooseningthethumbscrewsonthecase’sback
sideandremovingtheleftsidepanel.Laydownthecasesidewise
on an even surface.
2. Themainboard’smountingpanelinsidethecaseprovidesvarious
drillingstoscrewinthestand-offs(g.1).
 g.1
Themainboardcontainsspecialscrewopenings(g.2).
g.2
Place the mainboard to the mounting panel. A stand-off must be
screwed into every drilling of the mounting panel visible through
themainboard’sscrewopenings.
3. Remove the mainboard and screw the stand-offs into the respective
drillingsofthemountingpanel(g.3).
 (Stand-offs)
g.3
4. PresstheI/Oshield(deliveredwiththemainboard)intotheI/O
shieldopeninginthecase’sbackside.
scorpio 1000/2000
5. Place the mainboard back onto the stand-offs and screw the
mainboardtothem(g.4).
(Screwsformainboardmounting)
g.4
6. Plugtheconnectorsofthecase’sfrontbezeltotherespective
connectorsofthemainboard(alsorefertoyourmainboard’s
manualforfurtherinformation).
Note:
The eSATA cable connected to the front eSATA connection should
not exceed 50 cm of length otherwise transmission errors may
occur! With premium quality eSATA cables this maximum length
may be exceeded.
5. Installing a HDD
5.1 Fast Swap bays
1. Set up the case in front of you.
2. Open the bezel of the Fast Swap bays. Unlock one mounting
frame’sdetentlever,pullthemountingframetowardsyouand
takeitoutofthecase(g.5).
g.5
3. Placea3.5"SATAHDDintothemountingframe(connectors
pointingbackward/g.6).
g.6
scorpio 1000/2000
6. Connectthecircuitboard’sSATAdataconnectortoamatching
SATAdataconnectoronthemainboard(g.8).
 g.8
5.2 3.5" HDD cage
1. Attachthemountingrailstothe3.5“HDDfrombothsides(g.9).
 g.9
4. ScrewtheHDDtothemountingframefrombelow(g.7).
(ScrewswithcoarsethreadforHDDmounting)
 g.7
5. Slide the mounting frame back into the Fast Swap bay until its
detent lever locks and close the bezel.
scorpio 1000/2000
2. Slide the HDD with attached mounting rails into an available drive
bayinsidethe3.5"HDDcage(g.10).
g.10
3. Connect the built-in HDD to the mainboard.
5.3 3.5" drive bay
1. Removethecase’sleftandrightsidepanel.
2. Insert a 3.5" HDD into the drive bay below the Fast Swap drive
baysinsidethecase(g.11).
g.11
3. ScrewtheHDDtothedrivebayfrombothsides(g.12).
(ScrewswithcoarsethreadforHDDmounting)
 g.12
4. Connect the installed HDD to the mainboard.
scorpio 1000/2000
5.4 2.5" HDD cage
1. Inserta2.5“HDD/SSDintoadrivebayofthe2.5“HDDcageuntil
itlocksinsidethepre-installedplasticrail(g.13).
 g.13
2. Connect the inserted HDD to the mainboard.
6. Installing a PSU
1. PutthePSUfromtheinsideagainstthePSUbracketonthecase’s
backside(g.14).
g.14
Note:
The PSU may be installed in two different directions: either the
fan points upwards (towards the mainboard) or the fan points
downwards (towards the floor).
2. ScrewthePSUtothecasefromtheoutside(g.15).
(ScrewsforPSUmounting)
g.15
3. Connectthecircuitboard’s4-pinpowerconnectortoamatching
powerplugofthePSU(g.16).
g.16
scorpio 1000/2000
7. Installing an optical device
1. Reach into the case and push out the 5.25" front bezel from the
mountingbaywhereyouwanttoinstallthedrive(g.17).
 g.17
2. Inserttheopticaldriveintothecase’sdrivebayandattachitfrom
bothsidesusingthepre-installedquickfasteners(g.18).
g.18
3. Connect the optical drive to the power supply and the mainboard.
Note:
If you intend to transport the case we recommend securing
(additionally) the installed drives.
scorpio 1000/2000
8. Installing an add-on card
1. Remove the slot bezel from its attachment.
2. Inserttheadd-oncardintothemainboard’srespectiveslotand
screwittothecase(g.19).
(Screwsfordrive/mainboardmounting)
g.19
9. The pre-installed fans
1. The pre-installed case fans provide a 3-pin mainboard plug each.
2. Connect the plugs to either the respective mainboard or fan
connectorofthecircuitboard(g.20).
g.20
10. Installing additional fans /
optimized airflow
10.1 Side panel
1. Placethefan(1x200mmor2x120mm)againsttherespective
fan bracket from the inside. Screw the fan to the side panel from
the outside.
2. Connectthefan’spowerconnectortothemainboardorthePSU.
scorpio 1000/2000
10.2 Top panel
1. Dismantletheplasticcoverfromthecase’stopbyunscrewing
bothattachmentscrewsontherear(g.21).
g.21
2. Slide the cover backwards and lift it from the case.
3. Place the fan to the respective fan bracket from the inside. Screw
thefantothefanbracketfromtheoutside(g.22).
g.22
4. Connectthefan’spowerconnectortothePSUorthemainboard.
Note:
While installing fans make sure that (cool) air is taken in on the
case’s front side/bottom and blown out on its back side/top. The
PC components with the highest heat development should be
placed directly within the airflow.
scorpio 1000/2000
Legal disclaimer:
AsacontinuingpolicyofproductimprovementatSHARKOON,the
designandspecicationsaresubjecttochangewithoutpriornotice.
Nationalspecicationsmayvary.
Allrightsreservedespecially(alsoinextracts)fortranslation,
reprinting,reproductionbycopyingorothertechnicalmeans.
Infringements will lead to compensation.
All rights reserved especially in case of assignation of patent or utility
patent.Meansofdeliveryandtechnicalmodicationsreserved.
Disposal of your old product
Your product is designed and manufactured with high quality materials
andcomponents,whichcanberecycledandreused.
Whenthiscrossed-outwheeledbinsymbolisattachedtoaproduct,it
meanstheproductiscoveredbytheEuropeanDirective2002/96/EC.
Please be informed about the local separate collection system for
electrical and electronic products.
Please act according to your local rules and do not dispose of your
old products with your normal household waste. The correct disposal
of your old product will help prevent potential negative consequences
to the environment and human health.
© SHARKOON Technologies 2010
www.sharkoon.com
/