Comfort Glow CCL3930PT User manual

Brand: Comfort Glow

Model: CCL3930PT

Category: Space heaters

Type: User manual

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result

causing property damage, personal injury, or

loss of life.

— Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

— Installation and service must be performed by

a qualified installer, service agency, or the gas

WARNING: Improper installation, adjust-

ment, alteration, service, or maintenance

can cause injury or property damage.

Refer to this manual for correct installa-

tion and operational procedures. For as-

sistance or additional information con-

sult a qualified installer, service agency,

or the gas supplier.

WARNING: This appliance is for installa-

tion only in a solid-fuel burning masonry

or UL127 factory-built fireplace, or in an

approved ventless firebox. It is design-

certified for these installations in accor-

dance with ANSI Z21.11.2. Exception: Do

not install this appliance in a factory-

built fireplace that includes instructions

stating it has not been tested or should

not be used with unvented gas logs.

WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it

is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to

Air for Combustion and Ventilation

section on page 4 of this manual.

18", 24", and 30" Variable

Manually-Controlled Models

CGD3018P CCL3924P

CGD3924P CRL2718P

CGD3930P CRL3124P

CCL3018P

18", 24", and 30"

Thermostatically-Controlled

Models

CGD3924PT CGD3930PT

CGD3018PT CCL3018PT

CCL3924PT CCL3930PTA

Patent Pending

This appliance may be installed in an aftermarket,* permanently located, manufactured

(mobile) home, where not prohibited by local codes.

This appliance is only for use with type of gas indicated on the rating plate. This appliance

is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

(Smoky Mountain Oak Model Shown)

UNVENTED (VENT-FREE) PROPANE/LP

GAS LOG HEATER

OWNER’S OPERATION AND INSTALLATION

MANUAL

Save this manual for future reference.

For more information, visit www.desatech.com

BILTMORE SPLIT OAK, SEASONAL OAK

AND SMOKY MOUNTAIN OAK LOGS

Variable Manually-Controlled Models Also Design-Certified

As Vented Decorative Appliances

107124-01E

For more information, visit www.desatech.com

SAFETY INFORMATION

DANGER: Carbon monoxide poisoning may lead

to death!

Carbon Monoxide Poisoning: Early signs of carbon monoxide

poisoning resemble the flu, with headaches, dizziness, or nausea. If

you have these signs, the heater may not be working properly. Get

fresh air at once! Have heater serviced. Some people are more

affected by carbon monoxide than others. These include pregnant

women, people with heart or lung disease or anemia, those under the

influence of alcohol, and those at high altitudes.

Propane/LP Gas: Propane/LP gas is odorless. An odor-making

agent is added to the gas. The odor helps you detect a gas leak.

However, the odor added to the gas can fade. Gas may be present

even though no odor exists.

Make certain you read and understand all warnings. Keep this

manual for reference. It is your guide to safe and proper operation

of this heater.

WARNING ICON G 001

WARNINGS

IMPORTANT: Read this owner’s manual carefully and

completely before trying to assemble, operate, or ser-

vice this heater. Improper use of this heater can cause

serious injury or death from burns, fire, explosion,

electrical shock, and carbon monoxide poisoning.

WARNING: Any change to this heater or its con-

trols can be dangerous.

WARNING: Do not allow fans to blow directly into

the fireplace. Avoid any drafts that alter burner flame

patterns. Ceiling fans can create drafts that alter

burner flame patterns. Altered burner patterns can

cause sooting.

WARNING: Do not use a blower insert, heat

exchanger insert, or other accessory not approved

for use with this heater.

Due to high temperatures, the appliance should be

located out of traffic and away from furniture and

draperies.

Do not place clothing or other flammable material on

or near the appliance. Never place any objects on the

heater.

Heater base assembly becomes very hot when run-

ning heater. Keep children and adults away from hot

surface to avoid burns or clothing ignition. Heater

will remain hot for a time after shutdown. Allow

surface to cool before touching.

Carefully supervise young children when they are in

the room with heater.

You must operate this heater with a fireplace screen

in place. Make sure fireplace screen is closed before

running heater.

Keep the appliance area clear and free from combus-

tible materials, gasoline, and other flammable vapors

and liquids.

TABLE OF CONTENTS

SAFETY INFORMATION

TABLE OF CONTENTS

SAFETY INFORMATION ............................................................ 2

PRODUCT IDENTIFICATION ..................................................... 3

LOCAL CODES........................................................................... 4

UNPACKING ............................................................................... 4

PRODUCT FEATURES .............................................................. 4

AIR FOR COMBUSTION AND VENTILATION ........................... 4

INSTALLATION ........................................................................... 7

OPERATING HEATER .............................................................. 19

INSPECTING BURNERS.......................................................... 22

CLEANING AND MAINTENANCE ............................................ 23

TROUBLESHOOTING .............................................................. 24

OPTIONAL POSITIONING OF THERMOSTAT

SENSING BULB................................................................... 27

REPLACEMENT PARTS .......................................................... 28

SERVICE HINTS....................................................................... 28

TECHNICAL SERVICE ............................................................. 28

ACCESSORIES ........................................................................ 28

SPECIFICATIONS .................................................................... 29

ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 30

PARTS CENTRAL..................................................................... 40

OWNER'S REGISTRATION FORM .......................................... 41

WARRANTY INFORMATION...................................... Back Cover

107124-01E

For more information, visit www.desatech.com

SAFETY INFORMATION

Continued

1. This appliance is only for use with the type of gas indicated on

the rating plate. This appliance is not convertible for use with

other gases.

2. Do not place propane/LP supply tank(s) inside any structure.

Locate propane/LP supply tank(s) outdoors.

3. To prevent performance problems, do not use propane/LP fuel

tank of less than 100 lbs. capacity.

4. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in

your building

• immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions

• if you cannot reach your gas supplier, call the fire department

5. This heater shall not be installed in a bedroom or bathroom unless

installed as a vented appliance (Variable Manually-Controlled

Models Only) (see Installing Damper Clamp Accessory for

Vented Operation, page 10).

6. Before installing in a solid fuel burning fireplace, the chimney

flue and firebox must be cleaned of soot, creosote, ashes and

loose paint by a qualified chimney cleaner. Creosote will ig-

nite if highly heated. Inspect chimney flue for damage. If dam-

aged, operate heater with flue damper closed.

7. If fireplace has glass doors, never operate this heater with glass

doors closed. If you operate heater with doors closed, heat

buildup inside fireplace will cause glass to burst. Also if fire-

place opening has vents at the bottom, you must open the vents

before operating heater.

8. This log heater is designed to be smokeless. If logs ever appear

to smoke, turn off heater and call a qualified service person.

Note:

During initial operation, slight smoking could occur due

to log curing and heater burning manufacturing residues.

9. To prevent the creation of soot, follow the instructions in Clean-

ing and Maintenance, page 23.

10. Before using furniture polish, wax, carpet cleaner, or similar

products, turn heater off. If heated, the vapors from these prod-

ucts may create a white powder residue within burner box or

on adjacent walls or furniture.

11. This heater needs fresh, outside air ventilation to run properly.

This heater has an Oxygen Depletion Sensing (ODS) safety

shutoff system. The ODS shuts down the heater if not enough

fresh air is available. See Air for Combustion and Ventilation,

pages 4 through 6. If heater keeps shutting off, see Trouble-

shooting, pages 24 through 26.

12. Do not run heater

• where flammable liquids or vapors are used or stored

• under dusty conditions

13. Do not use this heater to cook food or burn paper or other objects.

SAFETY INFORMATION

PRODUCT IDENTIFICATION

Figure 1 - Vent-Free Gas Log Heater - Dual Burner (Logs May

Vary by Model - Smoky Mountain Oak Model Shown)

Figure 2 - Vent-Free Gas Log Heater - Single Burner (Logs May

Vary by Model - Seasonal Oak Model Shown)

14. Do not use heater if any part has been exposed to or under wa-

ter. Immediately call a qualified service technician to inspect

the room heater and to replace any part of the control system

and any gas control which has been under water.

15. Do not operate heater if any log is broken. Do not operate

heater if a log is chipped (dime-sized or larger).

16. Turn heater off and let cool before servicing. Only a qualified

service person should service and repair heater.

17. Operating heater above elevations of 4,500 feet could cause

pilot outage.

18.

Provide adequate clearances around air openings.

Middle Log

Front Log

Control Knob

Back Log

Base

Grate

Burner

Piezo

Ignitor

Crossover

Log

Front Log

Control Knob

Back Log

Burner

Piezo Ignitor

Crossover Log

107124-01E

For more information, visit www.desatech.com

AIR FOR COMBUSTION AND

VENTILATION

Today’s homes are built more energy efficient than ever. New

materials, increased insulation, and new construction methods help

reduce heat loss in homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out and the warm air

in. During heating months, home owners want their homes as airtight

as possible.

While it is good to make your home energy efficient, your home

needs to breathe. Fresh air must enter your home. All fuel-burning

appliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances

draw air from the house to operate. You must provide adequate fresh

air for these appliances. This will insure proper venting of vented

fuel-burning appliances.

PROVIDING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation

classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will help you classify your

space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough

fresh air for combustion and ventilation. However, in buildings of

unusually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction

where:

a. walls and ceilings exposed to the outside atmosphere

have a continuous water vapor retarder with a rating

of one perm (6x10

-11

kg per pa-sec-m

) or less with

openings gasketed or sealed

and

b. weather stripping has been added on openable win-

dows and doors

and

WARNING: This heater shall not be installed in a

confined space or unusually tight construction unless

provisions are provided for adequate combustion and

ventilation air. Read the following instructions to in-

sure proper fresh air for this and other fuel-burning

appliances in your home.

LOCAL CODES

Install and use heater with care. Follow all local codes. In the absence

of local codes, use the latest edition of The National Fuel Gas Code,

ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Note:

Where listed vented decorative logs are required, thermo-

stat operation is not permitted.

OPERATION

This heater is clean burning. It requires no outside venting. There is

no heat loss out a vent or up a chimney. Heat is generated by realistic

dancing, yellow flames. This heater is designed for vent-free opera-

tion with flue damper closed. It has been tested and approved to

ANSI Z21.11.2 standard for unvented heaters. State and local codes

in some areas prohibit the use of vent-free heaters. This heater may

also be operated as a vented decorative (ANSI Z21.60) product by

opening the flue damper (non-thermostat operation only).

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS)

safety shutoff system. The ODS/pilot is a required feature for vent-

free room heaters. The ODS/pilot shuts off the heater if there is not

enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system requires no matches,

batteries, or other sources to light heater.

PRODUCT FEATURES

UNPACKING

1. Remove logs and heater base assembly from carton.

Note:

not pick up heater base assembly by burners. This could dam-

age heater. Always handle base assembly by grate.

2. Remove all protective packaging applied to logs and heater

for shipment.

3. Check all items for any shipping damage. If damaged, promptly

inform dealer where you bought heater.

CAUTION: Do not remove the data plates from the

grate assembly. The data plates contain important

product information.

LOCAL CODES

UNPACKING

PRODUCT FEATURES

AIR FOR COMBUSTION AND VENTILATION

Providing Adequate Ventilation

107124-01E

For more information, visit www.desatech.com

Confined and Unconfined Space

National Fuel Gas Code, ANSI Z223.1/NFPA 54 defines a confined

space as a space whose volume is less than 50 cubic feet per 1,000

Btu per hour (4.8 m

per kw) of the aggregate input rating of all

appliances installed in that space and an unconfined space as a space

whose volume is not less than 50 cubic feet per 1,000 Btu per hour

(4.8 m

per kw) of the aggregate input rating of all appliances

installed in that space. Rooms communicating directly with the

space in which the appliances are installed*, through openings not

furnished with doors, are considered a part of the unconfined space.

* Adjoining rooms are communicating only if there are doorless

passageways or ventilation grills between them.

DETERMINING FRESH-AIR FLOW FOR

HEATER LOCATION

Determining if You Have a Confined or Uncon-

fined Space

Use this work sheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining

rooms with doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = ___________ cu. ft. (volume of space)

Example:

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling

height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or open-

ings, add the volume of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr

the space can support.

__________ (volume of space) x 20 = (Maximum Btu/Hr the space

can support)

Example:

2560 cu. ft. (volume of space) x 20 = 51,200 (maximum

Btu/Hr the space can support)

AIR FOR COMBUSTION AND

VENTILATION

Continued

WARNING: If the area in which the heater may be

operated is smaller than that defined as an uncon-

fined space or if the building is of unusually tight

construction, provide adequate combustion and ven-

tilation air by one of the methods described in the

National Fuel Gas Code, ANSI Z223.1/NFPA 54 Sec-

tion 5.3

or applicable local codes

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater _____________ Btu/Hr

Gas water heater* _____________ Btu/Hr

Gas furnace _____________ Btu/Hr

Vented gas heater _____________ Btu/Hr

Gas fireplace logs _____________ Btu/Hr

Other gas appliances* + _____________ Btu/Hr

Total = _____________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws com-

bustion air from the outdoors and vents to the outdoors.

Example:

Gas water heater _____________ Btu/Hr

Vent-free heater + _____________ Btu/Hr

Total = _____________ Btu/Hr

4. Compare the maximum Btu/Hr the space can support with the actual

amount of Btu/Hr used.

__________________ Btu/Hr (maximum the space can support)

__________________ Btu/Hr (actual amount of Btu/Hr used)

Example:

51,200 Btu/Hr (maximum the space can support)

79,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/

Hr used is more than the maximum Btu/Hr the space can support. You must

provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the

extra space provides an unconfined space, remove door to adjoining

room or add ventilation grills between rooms. See Ventilation Air From

Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Out-

doors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support,

the space is an unconfined space. You will need no additional fresh air ventilation.

AIR FOR COMBUSTION AND VENTILATION

Providing Adequate Ventilation (Cont.)

Determining Fresh-Air Flow for Heater Location

c. caulking or sealants are applied to areas such as

joints around window and door frames, between sole

plates and floors, between wall-ceiling joints, between

wall panels, at penetrations for plumbing, electrical,

and gas lines, and at other openings.

If your home meets all of the three criteria above, you

must provide additional fresh air. See

Ventilation Air

From Outdoors

, page 6

If your home does not meet all of the three criteria above,

proceed to

Determining Fresh-Air Flow for Heater Loca-

tion

, below.

40,000

39,000

79,000

107124-01E

For more information, visit www.desatech.com

AIR FOR COMBUSTION AND

VENTILATION

Continued

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space.

When ventilating to an adjoining unconfined space, you must

provide two permanent openings: one within 12" of the ceiling and

one within 12" of the floor on the wall connecting the two spaces

(see options 1 and 2, Figure 3). You can also remove door into

adjoining room (see option 3, Figure 3). Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion

and Ventilation for required size of ventilation grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must

provide two permanent openings: one within 12" of the ceiling and

one within 12" of the floor. Connect these items directly to the

outdoors or spaces open to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

IMPORTANT:

Do not provide openings for inlet or outlet air into

attic if attic has a thermostat-controlled power vent. Heated air

entering the attic will activate the power vent.

Figure 4 - Ventilation Air from Outdoors

Figure 3 - Ventilation Air from Inside Building

Outlet

Air

Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air

Ventilated

Crawl Space

Crawl

Space

To Attic

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills

Into Adjoining

Room,

Option 1

12"

AIR FOR COMBUSTION AND VENTILATION

Ventilation Air

107124-01E

For more information, visit www.desatech.com

INSTALLATION

WARNING: A qualified service person must in-

stall heater. Follow all local codes.

WARNING: Before installing in a solid fuel burn-

ing fireplace, the chimney flue and firebox must be

cleaned of soot, creosote, ashes, and loose paint by

a qualified chimney cleaner. Creosote will ignite if

highly heated. A dirty chimney flue may create and

distribute soot within house. Inspect chimney flue

and firebox for damage. If damaged, operate heater

with flue damper closed.

WARNING: Seal any fresh air vents or ash clean-

out doors located on floor or wall of fireplace. If not,

drafting may cause pilot outage or sooting. Use a heat-

resistant sealant. Do not seal chimney flue damper.

WARNING: Never install the heater

• in a bedroom or bathroom unless installed as a

vented appliance (Variable Manually-Controlled

Models Only) (see page 10)

• in a recreational vehicle

• where curtains, furniture, clothing, or other flam-

mable objects are less than 42 inches from the

front, top, or sides of the heater

• in high traffic areas

• in windy or drafty areas

CAUTION: This heater creates warm air currents.

These currents move heat to wall surfaces next to

heater. Installing heater next to vinyl or cloth wall

coverings or operating heater where impurities (such

as, but not limited to, tobacco smoke, aromatic

candles, cleaning fluids, oil or kerosene lamps, etc.)

in the air exist, may discolor walls or cause odors.

IMPORTANT:

Vent-free heaters add moisture to the air. Although

this is beneficial, installing heater in rooms without enough venti-

lation air may cause mildew to form from too much moisture. See

Air for Combustion and Ventilation, pages 4 through 6.

CHECK GAS TYPE

Use only propane/LP gas. If your gas supply is not propane/LP, do

not install heater. Call dealer where you bought heater for proper

type heater.

NOTICE: State or local codes may only allow opera-

tion of this appliance in a vented configuration. Check

your state or local codes.

NOTICE: This heater is intended for use as supple-

mental heat. Use this heater along with your primary

heating system. Do not install this heater as your

primary heat source. If you have a central heating

system, you may run system’s circulating blower

while using log heater. This will help circulate the

heat from your log heater throughout the house. In

the event of a power outage, you can use this heater

as your primary heat source.

INSTALLATION AND CLEARANCES

(Vent-Free Operation Only)

WARNING: Maintain the minimum clearances. If

you can, provide greater clearances from floor, ceil-

ing, and adjoining wall.

LOG SIZING REQUIREMENTS

Minimum Firebox Size

Log Front Rear*

Size Height Depth Width Width

18" 17" 14" 24" 20"

24" 17" 14" 28" 21"

30" 17" 14" 34" 24"

MINIMUM FIREPLACE CLEARANCE

TO COMBUSTIBLE MATERIALS

Log Size Side Wall Ceiling

18", 24", 30" 16" 42"

*Measured at 14" depth

Carefully follow the instructions below. This will ensure safe

installation into a masonry, UL127-listed manufactured fireplace,

or certified vent-free firebox.

INSTALLATION

Check Gas Type

Installation and Clearances for Vent-Free Operation

107124-01E

For more information, visit www.desatech.com

INSTALLATION

Continued

NOTICE: Manual control heaters may be used as a

vented product. If so, you must always run heater with

chimney flue damper open. If running heater with

damper open, noncombustible material above fire-

place opening is not needed. Go to

Installing Damper

Clamp Accessory for Vented Operation,

page 10.

Minimum Clearances For Side Combustible Mate-

rial, Side Wall, and Ceiling

A. Clearances from the side of the fireplace cabinet to any com-

bustible material and wall should follow diagram in Figure 5.

Example:

The face of a mantel, bookshelf, etc. is made of

combustible material and protrudes 3

/2" from the wall. This

combustible material must be 4" from the side of the fireplace

opening (see Figure 5).

Note:

When installing your gas logs into a manufactured fire-

box, follow firebox manufacturer’s instructions for minimum

clearances to combustible materials.

B. Clearances from the top of the fireplace opening to the ceiling

should not be less than 42 inches.

Figure 5 - Minimum Clearance for Combustible to Wall

If Using Mantel

You must have noncombustible material(s) above the fireplace

opening. Noncombustible materials (such as slate, marble, tile, etc.)

must be at least 1/2 inch thick. With sheet metal, you must have

noncombustible material behind it. Noncombustible material must

extend at least 8" up (for all models). If noncombustible material is

less than 12", you must install the fireplace hood accessory (24" and

30" models only). Even if noncombustible material is more than

12", you may need the hood accessory to deflect heat away from

your mantel shelf. See Figure 6 and Figures 7 and 8 on page 9 for

minimum clearances.

IMPORTANT:

If you cannot meet these minimum clearances, you

must operate heater with chimney flue damper open. Go to Install-

ing Damper Clamp Accessory for Vented Operation, page 10.

Heat Resistant

Material

(A)

Minimum Noncombustible Material Clearances

If Not Using Mantel

Note:

If using a mantel, proceed to If Using Mantel. If not using a

mantel, follow the information below.

You must have noncombustible material(s) above the fireplace

opening. Noncombustible materials (such as slate, marble, tile,

etc.) must be at least 1/2 inch thick. With sheet metal, you must have

noncombustible material behind it. Noncombustible material must

extend at least 8" up (for all models). If noncombustible material is

less than 12", you must install the fireplace hood accessory (24" and

30" models only). See Figure 6 for minimum clearances.

IMPORTANT:

If you cannot meet these minimum clearances, you

must operate heater with chimney flue damper open. Go to Install-

ing Damper Clamp Accessory for Vented Operation, page 10.

Noncombustible Requirements for

Material Distance (A) Safe Installation

12" or more Noncombustible material okay.

Between 8" and 12" 24" or 30" Models: Install

fireplace hood accessory

(GA6050, GA6052, or

GA6053 see

Accessories,

page 28).

18" Model: Noncombustible

material okay.

Less than 8" Noncombustible material

must be extended to at least

8". See

Between 8" and 12",

above. If you cannot extend

material, you must operate

heater with flue damper open.

Figure 6 - Heat Resistant Material (Slate, Marble, Tile, etc.)

Above Fireplace

*Minimum 16 inches from Side Wall

Example

INSTALLATION

Installation and Clearances for Vent-Free Operation (Cont.)

107124-01E

For more information, visit www.desatech.com

Figure 7 - Minimum Mantel Clearances Without Using Hood

Minimum Non-

Combustible

Material

Minimum Non-

Combustible

Material Height

Distances to

Underside of

Mantel

Top of Fireplace

Opening

Underside of

Mantel Shelf

12"

(A)

18"

20"

14"

22"

17"

24"

20"

All minimum

distances are

in inches

Log Set

24"/30" Models

18" Model

10"

MANTEL CLEARANCES

In addition to meeting noncombustible material clearances, you

must also meet required clearances between fireplace opening and

mantel shelf. If you do not meet the clearances in Figure 7, you will

need a hood.

Determining Minimum Mantel Clearance

If you meet minimum clearance between mantel shelf and top of

fireplace opening, a hood is not required (see Figure 7).

INSTALLATION

Continued

FLOOR CLEARANCES

A. If installing appliance on the floor level, you must maintain

the minimum distance of 14" to combustibles (see Figure 9).

B. If combustible materials are less than 14" to the fireplace, you

must install appliance at least 5" above the combustible floor-

ing (see Figure 10).

Determining Minimum Mantel Clearance When

Using a Hood

If minimum clearances in Figure 7 are not met, you must have a

hood. When using a hood there are still certain minimum mantel

clearances required. Follow minimum clearances shown in Figure

8 when using hood.

14"

Min.

Combustible

Material

Noncombustible

Material

Hearth

Min.

Combustible

Material

Figure 10 - Minimum Fireplace Clearances Above Combus-

tible Flooring

Figure 8 - Minimum Mantel Clearances When Using Hood

Minimum Non-

Combustible

Material

Min.

12" 15" 18"

All minimum

distances are

in inches

Log Set

18", 24", 30"

Models

20"

10"

12"

Distances to

Underside of

Mantel

Hood

(GA6050, GA6052)

Top of Fireplace

Opening

Underside of

Mantel Shelf

Figure 9 - Minimum Fireplace Clearances if Installed at Floor Level

(GA6050, GA6052,

and GA6053)

All Models

NOTICE: If your installation does not meet the mini-

mum clearances shown, you must do one of the

following:

• operate the logs only with the flue damper open

• raise the mantel to an acceptable height

• remove the mantel

NOTICE: Surface temperatures of adjacent walls and

mantels become hot during operation. Walls and

mantels above the firebox may become hot to the

touch. If installed properly, these temperatures meet

the requirement of the national product standard.

Follow all minimum clearances shown in this manual.

INSTALLATION

Mantel Clearances

Floor Clearances

107124-01E

For more information, visit www.desatech.com

INSTALLING HEATER BASE ASSEMBLY

WARNING: If installing in a sunken fireplace, special

care is needed. You must raise the fireplace floor to

allow access to heater control panel. This will insure

adequate air flow and guard against sooting and con-

trols being damaged. Raise fireplace floor with non-

combustible material. Make sure material is secure.

CAUTION: Do not pick up heater base assembly

by the burner. This could damage heater. Only handle

base assembly by grates.

IMPORTANT:

Make sure the heater burners are level. If heater is

not level, heater will not work properly. For thermostat models,

avoid damage to thermostat bulb. Avoid nicks or sharp bends in

thermostat bulb wire. Keep thermostat bulb in mounting bracket

until ready to mount base to floor. See Optional Positioning Of

Thermostat Sensing Bulb, page 27.

Installation Items Needed

• hardware package (provided with heater)

• approved flexible gas hose (not provided) (if allowed by local codes)

• sealant resistant to propane (propane/LP) gas, not provided

• electric drill with 3/16" drill bit

• flathead screwdriver

1. Apply pipe joint sealant lightly to male threads of the fitting to

be threaded into gas regulator. Connect approved flexible gas

hose to gas regulator of heater (see Figure 12).

IMPORTANT:

Hold gas regulator with wrench when

connecting flexible gas hose.

2. Locate masonry screws in hardware package.

3. Position heater base assembly in fireplace.

4. Place logs in their proper position on heater base, see Installing

Logs on pages 13 through 18.

5. Center heater base and logs front-to-back and side-to-side in

fireplace.

6. Carefully remove logs without moving heater base.

WARNING: You must secure this heater to fire-

place floor. If not, heater will move when you adjust

controls. Moving heater may cause a gas leak.

INSTALLATION

Continued

INSTALLING DAMPER CLAMP ACCESSORY

FOR VENTED OPERATION

Note:

When used as a vented heater, appliance must be installed

only in a solid-fuel burning fireplace with a working flue and

constructed of noncombustible material.

If your heater is a manually controlled model, you may use this

heater as a vented product. There are three reasons for operating

your heater in the vented mode.

1. The fireplace does not meet the clearance to combustibles re-

quirements for vent-free operation.

2. State or local codes do not permit vent-free operation.

3. You prefer vented operation.

If reasons number 1 or 2 above apply to you, you must permanently

open chimney flue damper. You must install the damper clamp

accessory (to order, see Accessories, page 28). This will insure vented

operation (see Figure 11). The damper clamp will keep damper open.

Installation instructions are included with clamp accessory.

See chart below for minimum permanent flue opening you must

provide. Attach damper clamp so the minimum permanent flue

opening will be maintained at all times.

Area of Various Standard

Round Flues

Diameter (ins.) Area (sq. ins.)

5" 20 sq. inches

6" 29 sq. inches

7" 39 sq. inches

8" 51 sq. inches

Chimney Minimum Permanent

Height (ft.) Flue Opening (sq. ins.)

6' to 15' 39 sq. inches

15' to 30' 29 sq. inches

CAUTION: Do not remove the data plates attached

to the heater base assembly. The data plates contain

important warranty and safety information.

INSTALLATION

Installing Damper Clamp Accessory for Vented Operation

Installing Heater Base Assembly

Figure 11 - Attaching Damper Clamp

Manufactured FireplaceMasonry Fireplace

Damper

Damper Clamp

Damper

Damper Clamp

Damper

107124-01E

For more information, visit www.desatech.com

Figure 12 - Attaching Flexible Gas Hose to Heater Gas Regulator

INSTALLATION

Continued

7. Mark screw locations through holes in mounting brackets (see

Figure 13 and 14). If installing in a brick-bottom fireplace, mark

screw locations in mortar joint of bricks.

8. Remove heater base from fireplace.

9. Drill holes at marked locations using 3/16" drill bit.

10. Attach base assembly to fireplace floor using two masonry

screws (in hardware package) (see Figure 13 or 14).

Figure 13 - Attaching Base Assembly to Fireplace Floor - Dual

Burner Model

Figure 14 - Attaching Base Assembly to Fireplace Floor - Single

Burner Model

Heater Gas

Regulator

Flexible Gas Hose

(if allowed by local

codes)

Fitting

Masonry

Screw

Mounting

Bracket

INSTALLATION

Installing Heater Base Assembly (Cont.)

Connecting to Gas Supply

Masonry

Screw

Mounting

Bracket

Figure 15 - External Regulator With Vent Pointing Down

CONNECTING TO GAS SUPPLY

WARNING: A qualified service person must con-

nect heater to gas supply. Follow all local codes.

CAUTION: Never connect heater directly to the

propane/LP supply. This heater requires an external

regulator (not supplied). Install the external regulator

between the heater and propane/LP supply.

Installation Items Needed

Before installing heater, make sure you have the items listed below.

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

* A CSA design-certified equipment shutoff valve with 1/8" NPT

tap is an acceptable alternative to test gauge connection. Purchase

the optional CSA design-certified equipment shutoff valve from

your dealer. See Accessories, page 28.

The installer must supply an external regulator. The external regulator

will reduce incoming gas pressure. You must reduce incoming gas

pressure to between 11 and 14 inches of water. If you do not reduce

incoming gas pressure, heater regulator damage could occur. Install

external regulator with the vent pointing down as shown in Figure 15.

Pointing the vent down protects it from freezing rain or sleet.

WARNING: This appliance requires a 1/2" NPT

(National Pipe Thread) inlet connection to the pres-

sure regulator.

Propane/LP

Supply Tank

External

Regulator

Vent Pointing

Down

107124-01E

For more information, visit www.desatech.com

CAUTION: Avoid damage to regulator. Hold gas

regulator with wrench when connecting it to gas

piping and/or fittings.

Figure 16 - Gas Connection

* Purchase the optional CSA design-certified equipment shutoff

valve from your dealer. See Accessories, page 28.

** Minimum inlet pressure for purpose of input adjustment.

Pressure Testing Gas Supply Piping system

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect appliance with its appliance main gas valve (control

valve) and equipment shutoff valve from gas supply piping sys-

tem. Pressures in excess of 1/2 psig will damage heater regulator.

2. Cap off open end of gas pipe where equipment shutoff valve

was connected.

3. Pressurize supply piping system by either using compressed

air or opening propane/LP supply tank valve.

4. Check all joints of gas supply piping system. Apply a noncor-

rosive leak detection fluid to all joints. Bubbles forming show

a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff valve to gas supply.

Check reconnected fittings for leaks.

WARNING: Never use an open flame to check for

a leak. Apply a noncorrosive leak detection fluid to all

joints. Bubbles forming show a leak. Correct all leaks

at once.

WARNING: Test all gas piping and connections

for leaks after installing or servicing. Correct all leaks

at once.

CAUTION: Make sure external regulator has been

installed between propane/LP supply and heater. See

guidelines under

Connecting to Gas Supply

, page 11.

CHECKING GAS CONNECTIONS

Installation must include an equipment shutoff valve, union, and

plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge

hook up. NPT tap must be upstream from heater (see Figure 16).

IMPORTANT:

Install equipment valve in an accessible location.

The equipment shutoff valve is for turning on or shutting off the gas

to the appliance.

Check your building codes for any special requirements for locating

equipment shutoff valve to fireplaces.

Apply pipe joint sealant lightly to male NPT threads. This will

prevent excess sealant from going into pipe. Excess sealant in pipe

could result in clogged heater valves.

CAUTION: Use only new, black iron or steel pipe.

Internally-tinned copper tubing may be used in certain

areas. Check your local codes. Use pipe of 1/2" diam-

eter or greater to allow proper gas volume to heater. If

pipe is too small, undue loss of volume will occur.

We recommend that you install a sediment trap in supply line as

shown in Figure 16. Locate sediment trap where it is within reach for

cleaning. Install in piping system between fuel supply and heater.

Locate sediment trap where trapped matter is not likely to freeze. A

sediment trap traps moisture and contaminants. This keeps them

from going into heater controls. If sediment trap is not installed or

is installed wrong, heater may not run properly.

WARNING: Use pipe joint sealant that is resistant

to liquid petroleum (LP) gas.

INSTALLATION

Continued

Cap

3" Minimum

Sediment Trap

Gas

Regulator

From External

Regulator

(11" W.C.** to

14" W.C.

Pressure)

CSA Design-Certified

Equipment Shutoff Valve

With 1/8" NPT Tap*

Approved Flexible Gas

Hose (if allowed by

local codes)

Tee Joint

Pipe Nipple

INSTALLATION

Connecting to Gas Supply (Cont.)

Checking Gas Connections

107124-01E

For more information, visit www.desatech.com

INSTALLATION

Continued

POSITION

OFF

POSITION

Figure 17 - Equipment Shutoff Valve

Open

Closed

Equipment

Shutoff

Valve

Figure 18 - Checking Gas Joints

Equipment

Shutoff Valve

Propane/LP

Supply Tank

Thermostat Gas Valve or

Control Valve Location

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 17).

2. Pressurize supply piping system by either using compressed

air or opening propane/LP supply tank valve.

3. Check all joints from propane/LP supply tank to equipment

shutoff valve (see Figure 18). Apply a noncorrosive leak de-

tection fluid to all joints. Bubbles forming show a leak.

4. Correct all leaks at once.

Pressure Testing Heater Gas Connections

1. Open equipment shutoff valve (see Figure 17).

2. Open propane/LP supply tank valve.

3. Make sure control knob of heater is in the OFF position.

4. Check all joints from equipment shutoff valve to control valve

(see Figure 18). Apply a noncorrosive leak detection fluid to

all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light heater (see Operating Heater, pages 19 and 20 [manu-

ally-controlled models] or pages 20 and 21 [thermostatically-

controlled models]). Check all other internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to Appliance, page 20

[manually-controlled models] or page 21 [thermostatically-con-

trolled models]).

WARNING: Failure to position the parts in accor-

dance with these diagrams or failure to use only parts

specifically approved with this heater may result in

property damage or personal injury.

INSTALLING LOGS

Each log is marked with a number. These numbers will help you

identify the log when installing. It is very important to install these

logs exactly as instructed. Do not modify logs. Only use logs

supplied with heater.

1. Locate pins on the bottom of back log (#1). Slide these pins into

the holes in the grate base behind the burner (see Figure 19).

Figure 19 - Installing Back Log (#1)

Hole in

Grate Base

Back Log

(#1)

Burner

Dual Burner Smoky Mountain Oak Models

CAUTION: After installation and periodically there-

after, check to ensure that no flame comes in contact

with any log. With the heater set to high, check to see

if flames contact any log. If so, reposition logs

according to the log installation instructions in this

manual. Flames contacting logs will create soot.

INSTALLATION

Checking Gas Connections (Cont.)

Installing Logs

107124-01E

For more information, visit www.desatech.com

INSTALLATION

Continued

Figure 20 - Installing Middle Log (#2)

Figure 21 - Installing Front Log (#3)

Figure 22 - Installing Crossover Log (#4)

Burner

Crossover Log (#4)

Notches

Rectangular

Knobs

Cutout

Tab

U-Shaped Slot

Middle Log (#2)

“U” Bend

Front Log (#3)

Post

Recess

Dual Burner Premium Aged Split Oak Models

WARNING: Failure to position the parts in accor-

dance with these diagrams or failure to use only parts

specifically approved with this heater may result in

property damage or personal injury.

Each log is marked with a number. These numbers will help you identify

the log when installing. It is very important to install these logs exactly as

instructed. Do not modify logs. Only use logs supplied with heater.

1. Place the base of the middle log (#1) in the U-shaped slots of

the grate base. The cutout on the right of the middle log should

fit over the burner (see Figure 23). Make sure the front of the

middle log is resting on the tabs of the grate base and the cut-

out area is centered over the burner “U” bend.

Burner

Tab

U-Shaped Slot

Middle Log (#1)

“U” Bend

Figure 23 - Installing Middle Log (#1)

2. Place the base of the middle log (#2) in the U-shaped slots of the

grate base in front of the back log. The cutout on the right of the

middle log should fit over the burner (see Figure 20). Make sure

the front of the middle log is resting on the tabs of the grate base

and the cutout area is centered over the burner “U” bend.

3. Locate the recesses on the back of the front log (#3). Fit these

recesses between the posts of the grate base (see Figure 21).

4. Locate the notches in the bottom of the crossover log (#4). Place

the crossover log on top of the middle log and front log. Make

sure the notches of the crossover log lines up with rectangular

knobs on top of the middle and front logs (see Figure 22).

5. Place lava rock around base of heater if desired. Do not put

lava rock on logs on burner.

INSTALLATION

Installing Logs (Cont.)

107124-01E

For more information, visit www.desatech.com

INSTALLATION

Continued

Hole in

Grate Base

Back Log (#2)

Burner

Figure 24 - Installing Back Log (#2)

Figure 25 - Installing Crossover Log (#3)

2. Locate pins on the bottom of back log (#2). Slide these pins into

the holes in the grate base behind the burner (see Figure 24).

3. Place crossover log (#3) onto the pin (right) on middle log (#1) and

into the recess of the back log (#2). See Figure 25.

4. Locate the notches in the bottom of the front log (#4). Place

the front log on the grate fingers. Make sure the notches of the

front log line up with the grate fingers. See Figure 26.

Front Log (#4)

Grate Fingers

Notches

Figure 26 - Installing Front Log (#4)

Figure 27 - Installing Log Piece (#5)

Log Piece (#5)

Crossover Log (#3)

5. With knot to right side, place smaller log piece (#5) over the

pin on the left side of the middle log. The smaller log will rest

on front log against the "knot" on the left. See Figure 27.

6. Place lava rock around base of heater if desired. Do not put

lava rock on logs on burner.

Recess

INSTALLATION

Installing Logs (Cont.)

107124-01E

For more information, visit www.desatech.com

Dual Burner Biltmore Split Oak Models

WARNING: Failure to position the parts in accor-

dance with these diagrams or failure to use only parts

specifically approved with this heater may result in

property damage or personal injury.

INSTALLATION

Continued

CAUTION: After installation and periodically there-

after, check to ensure that no flame comes in contact

with any log. With the heater set to HI, check to see if

flames contact any log. If so, reposition logs accord-

ing to the log installation instructions in this manual.

Flames contacting logs will create soot.

Each log is marked with a number. These numbers will help you

identify the log when installing. It is very important to install these

logs exactly as instructed. Do not modify logs. Only use logs supplied

with heater.

1. Place the front log (#1) on the grate fingers. Make sure the

front log rests firmly between the grate fingers and the grate

base (see Figure 28).

2. Place the base of the middle log (#2) in the U-shaped slots of the

grate base. The cutout on the right of the middle log should fit

over the burner (see Figure 29). Make sure the front of the middle

log is resting on the tabs of the grate base.

3. Locate pins on the bottom of back log (#3). Slide these pins into the

holes in the grate base behind the burner (see Figure 30).

4. Locate holes on the bottom of crossover log (#4). Slide front

hole onto the left pin (CCL3924PT or CCL3930PTA) or middle

pin (CCL3018P or CCL3018PT) on the middle log (#2) and

the pin on the back log (#3). See Figure 31 for placement.

Figure 28 - Installing Front Log (#1) (CCL3930PTA Shown)

Front Log (#1)

Grate

Fingers

Grate Base

Figure 29 - Installing Middle Log (#2) (CCL3930PTA Shown)

Figure 30 - Installing Rear Log (#3) (CCL3930PTA Shown)

Figure 31 - Installing Crossover Log (#4) (CCL3930PTA Shown)

Middle Log (#2)

Tab

Burner

U-Shaped Slot

Hole in Grate

Base

Pins

Burner

Log #2

Log #3

Pins

Log #4

INSTALLATION

Installing Logs (Cont.)

107124-01E

For more information, visit www.desatech.com

INSTALLATION

Continued

Figure 34 - Installing Crossover Log (#6)

(CCL3930PTA Shown)

Figure 35 - Installing Crossover Log (#7)

(Model CCL3930PTA Only)

Pins

Log #2

Front Log (#1)

Middle

Log (#2)

Crossover

Log (#6)

Holes

Pins

5. For CCL3924PT and CCL3930PTA Only: Locate pin and hole

on the bottom of crossover log (#5). Slide the pin into the hole

located in crossover log (#4). Slide the hole onto the pin on

front log (#1). See Figure 32.

For CCL3018P and CCL3018PT Only: Locate holes on the bot-

tom of crossover log (#5). Slide the holes over the left pins on

middle log (#2) and front log (#1). See Figure 33.

6. Locate holes on the bottom of crossover log (#6). Slide these

holes onto the right pins located in middle log (#2) and front

log (#1). See Figure 34.

7. For CCL3930PTA only: Locate holes on the bottom of cross-

over log (#7). Slide onto the pins located in crossover log (#6)

and middle log (#2). See Figure 35.

8. Add lava rock around base of heater if desired. Do not place

any lava rock on logs or burner.

Figure 32 - Installing Crossover Log (#5)

(CCL3930PTA Shown)

Crossover Log (#4)

Front Log (#1)

Crossover

Log (#4)

Front Log (#1)

Figure 33 - Installing Crossover Log (#5)

(CCL3018P and CCL3018PT Only)

INSTALLATION

Installing Logs (Cont.)

107124-01E

For more information, visit www.desatech.com

INSTALLATION

Installing Logs (Cont.)

Single Burner Seasonal Oak Models

WARNING: Failure to position the parts in accor-

dance with these diagrams or failure to use only parts

specifically approved with this heater may result in

property damage or personal injury.

The Seasonal Oak Log Set is a reversible log set. This means that the

two bottom logs may be turned to face either direction. The top log,

however, must remain in the same position. Do not modify logs.

Only use logs supplied with heater.

1. Place the back log onto the back of the base assembly. Make

sure log sits forward against the two posts in front of log (see

Figure 36). This log may be turned to face either direction.

2. Place front log onto grate on front of base assembly. The log

will fit down between grate fingers and posts on front of base

assembly (see Figure 37). This log may be turned to face ei-

ther direction.

3. Place the crossover log on top of the back log and front log

making sure pins are inserted into holes on top of logs 1 and 2

(see Figure 38). This log must be placed as shown in Figure 38

or the pins will not seat into holes.

4. Add lava rock around base of heater if desired. Do not put lava

rock on logs or burner.

Figure 36 - Installing Back Log

Figure 37 - Installing Front Log

Front Log

Grate

Fingers

Figure 38 - Installing Crossover Log

Back Log

Post

INSTALLATION

Continued

Base

Assembly

Post

Base

Assembly

Crossover Log

Hole in Back Log

Hole in

Front Log

107124-01E

For more information, visit www.desatech.com

OPERATING HEATER

Manually-Controlled Models

Figure 39 - Control Knob and Ignitor Button Location

PILOT

OFF

Ignitor Button

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions

exactly, a fire or explosion may result causing prop-

erty damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the floor because some gas

is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire de-

partment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by

hand, don’t try to repair it, call a qualified service techni-

cian or gas supplier. Force or attempted repair may result

in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

WARNING

• If fireplace has glass doors, never operate this

heater with glass doors closed. If you operate heater

with doors closed, heat buildup inside fireplace will

cause glass to burst. Also if fireplace opening has

vents at the bottom, you must open the vents before

operating heater.

• You must operate this heater with a fireplace screen

in place. Make sure fireplace screen is closed

before running heater.

NOTICE: During initial operation of new heater, burning

logs will give off a paper-burning smell. Orange flame

will also be present. Open damper or window to vent

smell. This will only last a few hours.

Note:

Home owners generally prefer to operate their heater

with the chimney damper closed. This will put all the heat into

the room. However, there may be times you will desire the full

flames of the HI heat setting but will find the heat output

excessive. You can open the chimney damper (if you have one)

fully or partially to release some of the heat.

LIGHTING INSTRUCTIONS

WARNING: Damper handle will be hot if heater

has been running.

Control Knob

1. STOP! Read the safety information in column one.

2. Make sure equipment shutoff valve is fully open.

3. Press in and turn control knob clockwise

Clockwise

to the

OFF position.

4. Wait five (5) minutes to clear out any gas. Then smell for

gas, including near the floor. If you smell gas, STOP! Fol-

low “B” in the safety information, column 1. If you don’t

smell gas, go to the next step.

5. Slightly depress and turn control knob counterclockwise

C-clockwise

to the PILOT position. Press in control knob for five

(5) seconds (see Figure 39).

Note:

You may be running this heater for the first time

after hooking up to gas supply. If so, the control knob may

need to be pressed in for 30 seconds or more. This will al-

low air to bleed from the gas system.

Figure 40 - Pilot

Thermocouple

Pilot Burner

Ignitor

Electrode

OPERATING HEATER (Manually Controlled Models)

For Your Safety Read Before Lighting

Lighting Instructions

107124-01E

For more information, visit www.desatech.com

1. Follow steps 1 through 5 under Lighting Instructions, page 19.

2. Depress control knob and light pilot with match.

3. Keep control knob pressed in for 30 seconds after lighting

pilot. After 30 seconds, release control knob. Now follow

step 8, under Lighting Instructions, column 1.

WARNING: If you do not follow these instructions

exactly, a fire or explosion may result causing prop-

erty damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the floor because some gas

is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire de-

partment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by

hand, don’t try to repair it, call a qualified service techni-

cian or gas supplier. Force or attempted repair may result

in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

TO TURN OFF GAS TO APPLIANCE

Shutting Off Heater

1. Press in and turn control knob clockwise

Clockwise

to the

HI position.

2. Turn control knob clockwise

Clockwise

to the pilot position.

3. Press in control knob and turn clockwise

Clockwise

to the

OFF position.

Shutting Off Burner(s) Only (pilot stays lit)

1. Turn control knob clockwise

Clockwise

to the HI position.

2. Press in and turn control knob clockwise

Clockwise

to the

pilot position.

CAUTION: Do not try to adjust heating levels by

using the equipment shutoff valve.

The variable control valve can be set to any heat setting and

flame height desired, by simply turning the control knob until

that setting is attained. Even the lowest setting provides realis-

tic, dancing yellow flames. Selecting higher settings produces

greater heat output. This results in increased heating comfort.

VARIABLE CONTROL OPERATION

MANUAL LIGHTING PROCEDURE

OPERATING HEATER

Continued

Thermostatically-Controlled Models

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: Do not operate heater between PILOT

and HIGH positions.

6. With control knob pressed in, press and release ignitor but-

ton. This will light pilot. The pilot is attached to the burner.

If needed, keep pressing ignitor button until pilot lights.

Note:

If pilot does not stay lit, contact a qualified service

person or gas supplier for repairs. Until repairs are made,

light pilot with match. To light pilot with match, see Manual

Lighting Procedure.

7. Keep control knob pressed in for 30 seconds after lighting

pilot. After 30 seconds, release control knob.

Note:

If pilot goes out, repeat steps 3 through 7. If control

knob does not pop out when released, contact a qualified

service person or gas supplier for repairs.

8. Slightly depress and turn control knob counterclockwise

C-clockwise

to desired heating level. The burner(s) should light.

Set control knob to any heat level between HI and LO.

OPERATING HEATER (Manually Controlled Models

Lighting Instructions (Cont.)

Variable Control Operation

To Turn Off Gas To Appliance

Manual Lighting Procedure

OPERATING HEATER (Thermostatically-Controlled Models)

For Your Safety Read Before Lighting

Page is loading ...

Comfort Glow CCL3930PT User manual

Brand: Comfort Glow

Model: CCL3930PT

Category: Space heaters

Type: User manual

Download PDF

report

Comfort Glow CCL3930PT User manual

Comfort Glow CCL3930PT User manual

Related papers

Other documents