Rointe Geneva Owner's manual

Brand: Rointe

Model: Geneva

Category: Water heaters & boilers

Type: Owner's manual

User Manual

Geneva water heater

Models

50 litres | 80 litres | 100 litres

Please read this manual carefully before installation and operation. Please keep this manual for future

reference and your product guarantee conditions.

CONTENTS

1. Introduction .............................................................................................................. 2

2. Components ............................................................................................................ 4

3. Installation - general ................................................................................................ 4

4. Installation - plumbing ............................................................................................. 6

5. Installation - electrical ............................................................................................ 10

6. Filling, commissioning and operation .....................................................................11

7. Troubleshooting ..................................................................................................... 12

8. Maintenance and cleaning ..................................................................................... 13

9. European Directive (WEEE) 2012/19/UE ............................................................... 14

10. Guarantee .............................................................................................................. 14

10.1 Terms and conditions .................................................................................... 14

10.2 How to register .............................................................................................. 17

11. Commissioning and service record ...................................................................... 18

12. Technical specication & data ............................................................................... 19

1. INTRODUCTION

Thank you for choosing this product. Please read this manual carefully before operation

and retain for further use.

ROINTE water heaters have passed the most stringent quality controls to meet all necessary

safety requirements. It is therefore imperative that this product is only installed by a trained

and competent person as deﬁned in the relevant regulations. ROINTE does not accept

any liability for damage done to persons or property resulting from incorrect installation,

or undue handling/usage of this product.

As part of ongoing product development and improvement ROINTE reserves the right to

undertake changes to the product without prior notice. Great care has been taken to ensure

this manual was correct at the time of print. Should you however discover any issues with

the information contained therein please do not hesitate to contact your vendor.

This product has been designed specically for the purpose of delivering heated, domestic

and sanitary hot water as part of a pressurised water heating system. Please ensure you

have purchased the relevant installation kit, which includes ttings that comply with Section

G3 of Building Regulations. This is necessary to complete the installation.

GENEVA UNVENTED WATER HEATER

IMPORTANT: When using electrical appliances, precautions should be taken to reduce

the risk of re, electrical shock and injury to persons.

IMPORTANT: It is important the tundish is positioned away from any electrical components.

It should terminate in a safe place where there is no risk to persons in the vicinity of the

discharge. The discharge will consist of scalding water and steam. Asphalt, roong felt

and non-metallic rainwater goods may be damaged by such discharges.

IMPORTANT: To disconnect the product from the main power supply, remove the plug

from the socket. Do not pull the cable.

WARNING: If the power cable is damaged, it must be replaced by ROINTE or its authorized

personnel in order to avoid any damage.

WARNING: Do not switch on the elecricity supply until instructed to do so in the

commissioning procedure and once the product is full of water.

WARNING: Servicing and product repairs should only be undertaken by ROINTE or its

authorized personnel using only exact manufacturer-approved spare parts.

WARNING: The product is IP24 rated and may be used in bathrooms, however not in the

immediate vicinity of baths, showers, water connections, basins, swimming pools or other

bodies of water. The product must never be installed where itself or the switches/control

panel is within the reach of persons in water. Never use the product with wet hands. Do

not place any water containers (glasses, vases etc.) on or near the product.

WARNING: To avoid overheating do not cover the product. This includes furniture, curtains,

clothes and any other items. Do not insert any kind of object in the product. Obstructions

should not be placed in front, above or directly next to the product. Do not use insecticides,

paints, chemicals or aerosols on or near the product. Do not sit on the product. Failure to

comply with the above will render your guarantee invalid.

WARNING: This product can be used by children aged over 8 years

and by persons with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge if they have been given supervision or

instruction concerning use of the product in a safe way and understand

the hazards involved. Children should not plug in, regulate, clean, play

with or perform maintenance on this product. Children aged less than 3

years should be kept away from the product unless supervised.

WARNING: If the cylinder is not being installed immediately, it should remain in its original

box with all pipe end protective caps in situ to prevent damage. We recommend that the

cylinder be transported to its installation position with the outer box in place.

2. COMPONENTS

This product is manufactured with CFC-free polyurethane insulation foam, a vitried steel

tank and copper heating elements. It also comes with a magnesium anode and a basic

control panel made of PP.

The product comes with the following components:

• Product with sheathed heating elements

• Basic control panel with external thermal regulator

• T/P valve 0.7 MPa 90ºC and electrolytic ttings

• Installation and user manual

3. INSTALLATION - GENERAL

3.1. Suitability

The product is suitable for domestic hot water systems where the cold mains water supply

has a maximum supply pressure of 0.9 MPa. Reduced performance is available at lower

pressures, but the product is not suitable for pressures lower than 0.15 MPa and a ow rate

of 20 litres per minute. The neccessary safety equipment to comply with all national

legislation is available for purchase from Rointe.

3.2. Water supply

The water supply to the cylinder should be potable water direct from a public mains water

supply with any water treatment equipment functioning correctly. For optimum performance

the unit should be fed via a 15 mm or 22 mm diameter supply pipe direct from the mains

water entry point to the property and supplies a maximum pressure of 0.9 MPa. The unit

can operate with a minimum supply pressure of 0.15 MPa and a ow rate of at least 20 litres

per minute, but ow from the outlets will be low if several outlets are used simultaneously.

The cylinder control equipment is factory set to limit the system operating pressure to 0.3

MPa. The maximum supply pressure into the pressure-reducing valve is 0.9 MPa.

3.3. Taps and ﬁttings

All taps and ttings incorporated in the unvented system should have a rated operating

pressure of 0.7 MPa or above.

We recommend using a Rointe Trusted Supplier. Find your nearest one by calling us on

0203 321 5928 or using the locator at www.rointe.co.uk.

IMPORTANT: Before installation, please locate the metal tag and note the product

reference and serial number. You will need this information to register your guarantee.

GENEVA UNVENTED WATER HEATER

WARNING: Do not install the product directly below a xed socket outlet or

connection box. Do not install or use outdoors. Do not install directly underneath a

shelf. This product is designed for internal wall-mounted installation using the ROINTE

template, installation kit and xing items provided.

3.4. Location and positioning

The unit is designed to be vertically wall mounted, indoors, in a frost-free environment.

When choosing a suitable location for the cylinder, consideration should be given to the

routing of the discharge pipe to a convenient point and also the availability of an adequate

power supply for connecting the sheathed heating elements.

The wall onto which the product is mounted must be of good sound masonry construction

capable of holding the weight of the cylinder when full of water (see section 11 “Technical

Specications” for weights).

The position of the cylinder should provide easy

access for servicing and replacing the sheathed

heating elements and magnesium anodes should

the need arise.

Pipe runs should be made as short as possible and

lagged to prevent heat loss.

To allow for servicing and repairs, the cylinder must

be mounted at least 500 mm above any object or

surface, so that access is available to the electric

connectors and the heating elements (if necessary)

may be removed (see gure opposite).

Never install the horizontal product with the wall

brackets on the oor or horizontal plane.

Please do not cover the products or place any

object (including furniture) directly in front of it.

We recommend this product is mounted close to an external wall so that the discharge

pipe can be routed to a safe, visible place.

The tundish should be mounted in a visible location so that it can be easily inspected.

WARNING: The product is IP22 rated, therefore must not be installed in bathrooms or

where itself or the control panel is within the reach of persons in water.

4. INSTALLATION - PLUMBING

Figure 2 - Cylinder connection arrangement

NO. DESCRIPTION

1 Mains cold water supply

2 Stop Cock (not included)

3 Pressure reducing valve*

4 Check valve*

5 Expansion relief valve*

6 Discharge pipe (22 mm)

7 Drain Cock (not included)

8 Tundish*

9 Expansion vessel*

10 T/P relief valve (included)

11 Electrical ttings (included)

* Available in installation kit

4.1. Connections

All pipework connections to the cylinder MUST be made in accordance with Figure 2. A

drain cock (not supplied) should be tted in the position shown in Figure 2 to facilitate

draining of the cylinder.

4.2. Electrical ﬁttings

The electrical ttings (Figure 2) must be tted to the product. If not, the guarantee will be

invalid. Check the T/P Relief Valve (Figure 2) to ensure it is connected with the electrical

ttings. If not, please contact us by telephoning 0203 321 5929.

4.3. Cold water supply

For best results, the cylinder should be fed by an uninterrupted supply pipe into the

pressure reducing valve (PRV) (Figure 2) with a maximum supply pressure of 0.9 MPa. The

cylinder should not be used on any system with a supply pressure below 0.15 MPa and a

ow rate of less than 20 litres per minute.

GENEVA UNVENTED WATER HEATER

4.4. Temperature and pressure relief valve

The temperature and pressure relief valve (T/P Valve) is supplied (Figure 2). Once the T/P

valve is tted it should not be removed from the cylinder or tampered with in any way. The

valve is pre calibrated to lift at 0.7 MPa or 90oC and any attempt to adjust it will render the

guarantee null and void and could affect the safety performance of the unit.

The outlet of the T/P valve should be routed in 15 mm copper piping in a downward direc-

tion alongside the product to the tundish in a frost-free environment. The expansion vessel

must be into the pressure reducing valve rst, and then T’d into the downpipe of the T/P

relief valve before the tundish.

4.5. Pressure reducing valve

The pressure reducing valve (Figure 2) should be installed in the cold water supply to the

water heating unit with the arrow pointing in the direction of water ow as shown in Figure

2. This can be connected to a maximum supply pressure of 0.9 MPa.

4.6. Expansion relief valve

This must be installed between the pressure reducing valve and the water heating unit

in accordance with Figure 2. No other valve should be tted between this valve and the

cylinder. The expansion relief valve contains a non return valve.

4.7. Expansion vessel

A suitable expansion vessel (Figure 2) with a pre-charge pressure of 0.15 or 0.3 MPa is

available in an optional kit for tting to all water heating units in the range. The expansion

vessel MUST be tted to the safety group. The expansion vessel MUST be positioned with

the entry point at the bottom (see Figure 2 above).

IMPORTANT: Regular checks must be carried out to ensure the expansion vessel is

correctly pressurised to 0.15 or 0.3 MPa at all times. Regular servicing and checks of

of the tank, heating elements and magnesium anodes is also recommended to ensure

the product is kept in good working condition and to maintain product guarantee.

4.8. Tundish

The tundish (Figure 2) must not be positioned above or in close proximity to any electrical

current carrying devices or wiring. The installation should conform with the requirements

of section 4.9.

4.9. Discharge arrangement

The tundish (Figure 2) must be installed in a position so that it is clearly visible by the user.

In addition, the discharge pipe (Figure 2) from the tundish should terminate in a safe place

where there is no risk to persons in the vicinity of the discharge, be of metal and:

a) Be at least one pipe size larger than the normal outlet size of the safety device unless

its total equipment hydraulic resistance exceeds that of a straight pipe 9m long, i.e.

discharge pipes between 9m and 18m equivalent resistance length should be at least

two sizes larger then the normal outlet size of the safety device, between 18m and 27m

at least three sizes larger and so on. Bends must be taken into account in calculating

the ow resistance. Refer to Figure 3, Table 1 and Calculated Example 1.

b) Have a vertical section of pipe at least 300 mm long below the tundish before any

elbows or bends in the pipework.

c) Be installed with a continuous fall.

d) Have discharges visible at both tundish and the nal point of discharge, but where

this is not possible or practically difcult, examples of acceptable discharge arrange-

ments are:

• Ideally below a xed grating and above the water seal in a trapped gully.

• External surfaces such as car parks, hard standings, grassed areas, etc.) are

acceptable providing that where children play or otherwise come into contact

with discharges, a wire cage or similar guard is positioned to prevent contact

whilst maintaining visibility.

• Discharge at high level, e.g. into a metal hopper and metal down pipe with the

end of the discharge pipe clearly visible (tundish visible or not) or onto a roof

capable of withstanding high temperature discharges of water and 3 m from any

plastic guttering system that would collect such discharges (tundish visible).

• Where a single pipe serves a number of discharges such as in blocks of ats,

the number served should be limited to not more than six systems so that any

installation discharging can be traced reasonably easily. The single common

discharge pipe should be at least one pipe size larger than the largest individ-

ual discharge pipe to be connected. If unvented hot water storage systems

are installed where discharges from safety devices may not be apparent (i.e. in

dwellings occupied by blind, or disabled people), consideration should be given

to the installation of an electrically operated device to warn when discharge

takes place.

WARNING: The discharge will consist of scalding water and steam. Asphalt, roong

felt and non-metallic rainwater goods may be damaged by such discharges.

GENEVA UNVENTED WATER HEATER

Figure 3 - Typical discharge pipe arrangement

Table 1 - Sizing of copper discharge pipe “D2” for common temperature relief valve

outlet sizes

Valve outlet

size

(diameter,

inches)

Min. size of

discharge

pipe D1 (mm)

Min. size of

discharge

pipe D2 (mm)

Max. resistance

allowed (length of

straight pipe - no

elbows / bends (m)

Resistance

created by each

elbow or bend (m)

G 1/2 15

up to 9

up to 18

up to 27

0.8

1.0

1.4

G 3/4 22

up to 9

up to 18

up to 27

1.0

1.4

1.7

G1 28

up to 9

up to 18

up to 27

1.4

1.7

2.3

Calculated Example 1

The example is for a 1/2” diameter temperature relief valve with a discharge pipe (D2)

having 4 x 22 mm elbows and a length of 7 m from the tundish to the point of discharge.

The maximum resistance allowed for a straight length of 22 mm copper discharge pipe (D2)

from a 1/2” diameter temperature relief valve is 9.0 m.

Subtract the resistance for 4 x no 22 mm elbows at 0.8 m each = 3.2 m. Therefore, the

maximum permitted length equates to: 5.8 m. This 5.8 m is less than the actual length of

7m, therefore, calculate the next largest size.

Maximum resistance allowed for a straight length of 28mm pipe (D2) from a 1/2” diameter

temperature relief valve equates to: 18 m. Subtract the resistance for 4 No 28 mm elbows

at 1.0 each = 4 m.

Therefore the maximum permitted length equates to: 14m. As the actual length is 7m, a 28

mm diameter copper pipe will be satisfactory.

5. INSTALLATION - ELECTRICAL

WARNING: This equipment and pipework must be earthed. All electrical wiring must

be carried out by a competent person and in accordance with current regulations.

5.1. Sheathed heating elements

Two parallel 1.2kW 230v 50Hz sheathed heating elements are pre tted to the cylinder.

5.2. Wiring

The power supply to the product must be via a double pole isolator switch or controller,

having contact separation of at least 3 mm, to comply with BS 6141 and must be fully

earthed. In case of an electric problem, check that the wiring follows:

a) The earth wire is connected to the cylinder terminal marked with the earth symbol.

b) The live wire is connected to the high temperature cut-out terminal.

c) The neutral wire is connected to the high temperature cut-out terminal.

WARNING: Do not switch on the elecricity supply until instructed to do so in the

commissioning procedure and once the product is full of water.

GENEVA UNVENTED WATER HEATER

6. FILLING, COMMISSIONING & OPERATION

6.1. Filling and commissioning

a) Check that the expansion vessel charge pressure is 0.15 or 0.3 MPa.

b) Check that all water and electric connections are correctly congured.

c) Open the main stopcock and ll the unit. Open successive hot taps starting with the

tap furthest from the product. Leave each tap open for a few moments to allow all air and

debris from the system to exit. Close all of the taps.

d) Turn off the mains water supply to the cylinder and drain the system through the drain

cock.

e) Rell the cylinder with hot taps open and close when water ows freely.

f) Manually lift (by rotating the knob) both the expansion relief and the temperature and

pressure relief valves for a short period to remove trapped air from behind the valve

seating and to check the correct function of the discharge arrangement.

g) Check all joints for leaks and rectify as necessary.

h) With the product full of water, switch on the electricity supply. Check that the cylinder

heats the water and the thermostat operates. Turn on the hot taps to check that warm

water is delivered.

i) Check that while the unit is heating up, no water exits from either the expansion relief

valve or the temperature and pressure relief valve. If water does exit through the valves

check the expansion vessel pressure and installation.

j) Increase the temperature to maximum and allow the unit to heat and the temperature

to stabilise. Check that no water discharges from the valves. Turn on the hot taps to

drain the product of hot water. Set the thermostat to the required temperature and allow

the product to reheat ready for use.

6.2. Guidance

When a hot tap is turned on there may be a short surge of water. This is quite normal with

unvented systems and does not mean there is a fault.

When you rst ll a basin the water may sometimes appear milky. This is due to very tiny

air bubbles in the water which will clear very quickly.

If water is seen dripping through the tundish at any time switch off the electricity supply

immediately and call the installer or the Rointe Technical Service department on 0203 321

5929.

6.3. Operation

To turn the product on/off, press the red switch on the front of the product. A light will

come on when the product is switched on.

To adjust the temperature, use the temperature dial located next to the on/off switch. To

increase temperature turn the dial to the right. To decrease the temperature, turn the dial

to the left.

7. TROUBLESHOOTING

WARNING: Disconnect electric supply before removing or repairing any electrical

equipment or covers over electrical equipment.

FAULT POSSIBLE CAUSE REMEDY

No hot water

1. Mains supply off.

2. Strainer in pressure

reducing valve blocked.

3. Pressure reducing valve

incorrectly tted.

1. Open stopcock.

2. Turn water supply off,

remove strainer and clean.

3. Re-t correctly.

Water from hot

taps is cold

1. Not switched on.

2. High limit thermostat has

tripped.

1. Switch on the product.

2. Check and reset.

Intermittent water

discharge through

tundish on warm-

1. Expansion vessel has lost

its charge pressure.

1. Turn off stopcock, open

a hot water tap, check

vessel charge pressure and

recharge

Continuous water

discharge

1. Pressure reducing valve not

working.

2. Expansion relief valve not

seating correctly.

3. Temperature and pressure

relief valve not seating

correctly.

1. Check pressure from

pressure reducing valve

if greater than 0.3 MPa

replace cartridge.

2. Manually lift the valve once

or twice to clear any debris

from the seat otherwise

replace valve.

GENEVA UNVENTED WATER HEATER

8. MAINTENANCE & CLEANING

Servicing and maintenance must only be carried out by a competent unvented hot

water professional or by Rointe authorised personnel, at least once per year. This

includes the tank, heating elements and magnesium anodes.

Before any work is carried out on the installation, it MUST rst be isolated from the mains

electricity supply. Only use spare parts authorised by Rointe. The use of other parts will

invalidate the warranty.

Drain the cylinder – When draining the cylinder, always switch off the product. Turn off the

water supply at the stopcock (see Figure 2). Connect a hosepipe to the drain cock (see

Figure 2) and route it to a convenient gully. Open the drain cock and all hot taps that are

served by the cylinder. The cylinder may take several minutes to empty completely.

Check the magnesium anode at least once per year, and replace if worn or defective.

Remove the cartridge from the pressure reducing valve. Check the strainer and if necessary

remove any debris from in front of it. Replace the cartridge.

Check the charge pressure in the expansion vessel and top up as necessary. The charge

pressure should be 0.15 or 0.3 MPa.

Close the drain cock, disconnect the hose, ret the heating element and close all hot water

taps before reopening the stopcock. Allow the cylinder time to ll whilst checking for any

leaks. Release any air from the system by opening each hot water tap individually, starting

with the one furthest from the cylinder.

Manually lift the expansion relief and temperature and pressure relief valve one at a time,

every 12 months (more frequently in hard water areas) to prevent debris from building up

behind the valve seat. Whilst carrying out this operation, check that the discharge to waste

is unobstructed. Check that each valve seals correctly when released. As the valves are

pre-calibrated, they require no further maintenance.

Finally, when the product is full of water switch on the mains electricity supply to the product.

As the system heats up, check again for any leaks and rectify as necessary.

In the event of the manual reset cut-out operating, isolate the product from the mains

supply, investigate and identify the cause of the operation of this cut-out, rectify the fault

before manually resetting the cut-out via the reset button on the cut-out. Finally switch the

mains electricity supply back on.

WARNING: Disconnect the product from the power supply before any cleaning or

maintenance. Do not use any abrasive product on the aluminium, such as (but not limited

to) chemicals, rough cloths, hard bristled brushes or wire/steel wool.

9. EUROPEAN DIRECTIVE (WEEE) 2012/19/UE

Under the European Directive 2012/19/UE on Waste Electrical and Electronic Equipment

(WEEE), this product cannot be treated as household waste. Instead it must be separated

to optimize the recovery and recycling of all of the components and materials to reduce

the impact on human health and the environment. The symbol of the container crossed out

over a horizontal line is marked on all of ROINTE products to remind the consumer of the

obligation to separate them on disposal. The consumer should contact their local authority

or council ofce, or original point of sale to learn about the correct method of disposal for

this product.

10. GUARANTEE

There are certain terms and conditions on this ROINTE product. These conditions comply

with all the rights construed within national legislation, as well as any additional rights and

guarantees, which are offered by ROINTE. Please ensure that you register your product

guarantee at www.rointe.co.uk.

Any incident you might detect with your product can be sorted by the product seller or by

ROINTE. Please contact ROINTE by telephoning 0203 321 5929 or send an email to

[email protected], through which we will instruct you on how to solve the incident.

You will need to state the product reference and serial number (located on the metal

tag with the product) and the type of incident when contacting ROINTE. In addition,

please attach a copy of the product invoice and/or proof of purchase that indicates

the date on which the product was sold.

GENEVA

10.1. Terms & conditions

1. ROINTE guarantees there are no material defects of design or manufacture at the

time of original purchase. ROINTE guarantees the tank for 60 months and electric plus

electronic components for 24 months for this product only, provided it has not been

modied in any way.

2. If during the guarantee period, the product does not work correctly under normal use,

and any design, material or manufacturing defect is found, ROINTE will repair or substitute

the product as it sees t, in accordance with the terms and conditions as follows:

GENEVA UNVENTED WATER HEATER

2.1. The guarantee is only applicable if the original guarantee is issued by the seller and

when the said guarantee has been registered with ROINTE correctly, including product

reference, series number (marked on the product’s metal tag), purchase date and proof of

purchase. The product guarantee can be registered on our website at www.rointe.co.uk

or can be sent via email to [email protected] within 90 days of installation. ROINTE

reserves the right to reject the guarantee when this information has been removed or

modied after the original product purchase.

2.2. The guarantee is only applicable if the product has been installed by a competent

person in accordance with this installation manual and all current regulations at the time

of installation.

2.3. The guarantee is only applicable to those cases that concern material, design and

manufacturing defects, and under no circumstances covers damage to the product for

the following reasons:

i) Damage caused by negligence and / or misuse of the product, i.e. used for other

purposes that are not construed as its normal use or for not respecting instructions

of use, servicing or maintenance given by ROINTE, as well as incorrect installation or

use of the product that may not comply with the current technical standards of safety.

ii) Corrosion of any part of the product caused by direct exposure to salt-water. When

the product is installed less than 200m from the coast, the guarantee period for

damages caused by corrosion will be reduced by 50%.

iii) Any unauthorised modication of the product or repairs of the product carried out

by third parties or unauthorised persons, or opening of the product by third parties or

unauthorised persons.

iv) Any accidents that are deemed outside the control of ROINTE, such as (but not

limited to): lightning, res, oods, natural disasters, public disorder, atmospheric or

geologic phenomena etc.

v) Faults that result from incorrect installation. Guidance can be found from Rointe and

in this installation manual. If in doubt, please contact ROINTE.

2.4. Any repairs or substitutions completed as part of this guarantee service do not allow

extension periods or new periods of guarantee i.e. your guarantee will not be extended

should a repair or substitution of this product take place.

2.5. Any repairs or substitutions covered under this guarantee must be parts that are

functionally equivalent. The defective parts or parts removed or replaced shall become

the property of ROINTE and should be returned as such.

2.6. The product must be installed in a way that allows access for ROINTE technicians

or authorised persons should they need to gain access to the product for repair or

maintenance. The user/client is responsible for any costs or organisation required to

provide access to the products for repair and/or substitution.

2.7. The product has been installed indoors, in a frost free environment and has solely

been used for the purpose of heating potable water that complies with current (at time

of installation) regulations and standards and is not fed with water from a private source.

2.8. The product has not been subjected to excessive pressure or electrolytic actions

from dissimilar materials or attack from salt deposits.

3. The ROINTE Technical Support department will advise you if you need to purchase any

parts not covered under this guarantee or out of guarantee.

4. This guarantee will be invalid if the product: has been manipulated, modied and/or

repaired in any way and/or by unauthorised persons. This guarantee will also be invalid if the

product is not correctly installed, or has not undergone an annual inspection or service by

a competent professional. This includes inspection and repair of the tank, heating elements

and magnesium anodes. Magnesium anode repair or replacement is the responsibility of

the user and not ROINTE.

5. This guarantee is not transferable and does not include claims due to damage by lime

scale or frost.

6. Proof of purchase will be required by ROINTE for any claim.

7. This guarantee does not affect your statutory rights.

8. This guarantee does not affect the buyer’s legal rights stipulated in current national

legislation, nor affects those rights against the distributor or installer that could come forth

in compliance with the purchase contract.

9. In the absence of applicable national legislation, this guarantee shall prevail and may

be construed as the buyer’s only protection. ROINTE, its ofces, employees, distributors

and installers will not be held responsible for any accidental damage that emerges due to

infringement of any rules implicitly related to this product.

For help about the product or guarantee, please contact ROINTE by phoning

0203 321 5929 or send an email to [email protected].

10.2. How to register your product guarantee

GENEVA UNVENTED WATER HEATER

IMPORTANT: It’s important to register your ROINTE product as part of our guarantee

service, in case you wish to make a claim.

You can register your ROINTE product in the following ways:

WEBSITE

1. Go to www.rointe.com/uk/register-your-guarantee/.

2. Login to your existing account or create a new account if you need to.

3. Click on “My products”.

4. Enter your product reference (alphanumeric and in upper case).

5. Enter your serial number (26 digits located on the metal tag on your product and

starts with 843).

6. Upload your proof of purchase, such as invoice in PDF, JPEG or PNG format. This

is not mandatory but by doing so you ensure your guarantee period is accurate.

7. Click “Register”.

8. Congratulations! Your product is now registered.

1. Send an email to [email protected] with the following information:

• Customer name

• Address and postcode

• Telephone number and email address

• Product reference (as described above)

• Serial number (as described above)

• Product purchase date and proof of purchase (as described above).

2. Our Technical Support team will conrm your product registration and request any

additional information needed via email.

POST

1. Post the information listed in the EMAIL section above to:

• INDUSTRIAS ROYAL TERMIC, S.L. t/a Rointe UK, C/E Parcela 43, 30140,

Santomera (SPAIN)

Please ensure you obtain proof of posting.

11. COMMISSIONING & SERVICE RECORD

11.1. Commissioning record

CUSTOMER DETAILS

Model: Telephone:

Address:

PRODUCT DETAILS

Model: Product ref:

Capacity (litres) Serial no:

INSTALLER DETAILS

Company name: Date:

Address:

Telephone:

Installer name: Registration no.

COMMISSIONING ENGINEER (IF DIFFERENT)

Company name: Date:

Address:

Telephone:

Installer name: Registration no.

11.2. Service record

Before completing the appropriate Service Record below, please ensure you have carried

out the service as described in the manufacturer’s instructions and in compliance with all

relevant codes of practice. It is recommended that your water heater is serviced regularly

and that your service engineer completes the appropriate Service Record below.

SERVICE 1 DATE SERVICE 2 DATE

SERVICE ENGINEER SERVICE ENGINEER

TEL NO. TEL NO.

REGISTRATION NO. REGISTRATION NO.

SIGNATURE SIGNATURE

SERVICE 3 DATE SERVICE 4 DATE

SERVICE ENGINEER SERVICE ENGINEER

TEL NO. TEL NO.

REGISTRATION NO. REGISTRATION NO.

SIGNATURE SIGNATURE

GENEVA UNVENTED WATER HEATER

12. TECHNICAL SPEC

MODEL 050DHW4 080DHW4 100DHW4

Volume (L) 50 80 100

MATERIALS

Vitried steel tank

CFC-free ployurethane foam

Basic control panel made of PP

Copper heating elements

DIMENSIONS, WEIGHTS & FINISHES

Diameter (mm) 440 440 440

Height (mm) 597 847 987

Installed depth (mm) 490 490 490

Distance between connections (mm) 110 110 110

Water connection (““) 1/2 1/2 1/2

Empty weight (kg) 15.7 21.4 24.0

Maximum working pressure (bar) 8

Finish White RAL 9016

ELECTRICAL CHARACTERISTICS

Load prole M L L

Nominal Power (W) 1,500 1,500 1,500

Voltage (V) 230 ~V 230 ~V 230 ~V

Current (A)

INSTALLATION & SAFETY

Magnesium anode

Safety thermostat

Installation position Vertical

Installation kit (sold separately)

Protection Grade IP22 IP22 IP22

GUARANTEES

Tank 5 years 5 years 5 years

Electronics & electrical components 2 years 2 years 2 years

EAN CODES 8435556141297 8435556141303 8435556141310

Rointe United Kingdom

Hampton Business Park, Club Way,

Peterborough PE7 8JA

T. 0203 321 5928

Rointe Ireland

Blackrock, County Louth

T. 01 553 0523

Rointe España & Portugal

P.I. Vicente Antolinos - C/ E, p. 43, 30140 Murcia

T. 902 158 049

Rointe France

6 Rue Duret, 75116 Paris

T. 01 73 05 70 01

part of our continuous improvement policy, we reserve

the right to alter or modify any product or speciﬁcations

without notice. This also applies to products already on

order provided that such alterations can be made without

subsequent changes to speciﬁcations already agreed. We

cannot accept responsibility for any errors in catalogues

or other printed materials.

MRGENTUK-V1

ª”~“±

www.rointe.co.uk/technical-support

[email protected]

0203 321 5929

Monday to Friday from 8.00 am to 5.00 pm.

If you have any questions or need help, please contact us:

Rointe Geneva Owner's manual

Brand: Rointe

Model: Geneva

Category: Water heaters & boilers

Type: Owner's manual

Download PDF

report

Rointe Geneva Owner's manual

Rointe Geneva Owner's manual

Related papers

Other documents