Briggs & Stratton 030452-0 Owner's manual

Brand: Briggs & Stratton

Model: 030452-0

Category: Power generators

Type: Owner's manual

This manual is also suitable for

30452

PortableGenerator

Operator'sManual

This generator is rated in accordance with CSA(Canadian Standards

Association) standard 022.2 No. 100-04 (motors and generators).

BRIGGS & STRATTONPOWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

Manual No. 209760GS Revision - (04/20/2009)

Thankyou for purchasing this quality-built Briggs & Stratton generator.We are pleasedthat you've placedyour confidence in

the Briggs & Stratton brand. When operatedand maintainedaccordingto the instructions in this manual,your Briggs &

Stratton generator will provide many years of dependableservice.

Thismanualcontainssafety information to makeyou awareof the hazardsand risks associatedwith generators and how to

avoid them. This generator is designed andintendedonly for supplying electrical powerfor operatingcompatible electrical

lighting, appliances,tools and motor loads, and is not intendedfor any other purpose. It is important that you read and

understand these instructions thoroughly before attempting to start or operatethis equipment. Save these instructionsfor

future reference.

Thisgenerator requiresfinal assembly beforeuse. Referto the Assemb/ysection of this manualfor instructions on final

assembly procedures. Follow the instructions completely.

Whereto FindUs

You neverhaveto lookfar to find Briggs & Stratton support and servicefor your generator.Consultyour Yellow Pages.There

are over 30,000 Briggs & Stratton authorizedservicedealersworldwide who provide quality service.You canalso contact

Briggs & Stratton CustomerServiceby phone at (800) 743-4115, or on the Internetat BRIGGSandSTRATTON.COM.

Generator

Model Number

Revision I I I

Serial Number

Engine

Model Number

Type Number LLL_ I I I

Code Number

DatePurchased

IIIIIIIII

Briggs & Stratton PowerProducts Group, LLC

900 North Parkway

Jefferson, WI 53549

material may be reproduced or transmitted in any form

without the expresswritten permission of Briggs & Stratton

Power Products Group, LLC.

2 BRIGGSandSTRATTON.COIVl

TableofContents

Operator Safety ................................. 4

Equipment Description......................................... 4

Important SafetyInformation.................................... 4

Assembly ..................................... 7

UnpackGenerator ............................................ 7

Install Wheel Kit.............................................. 7

Verify EngineOil Level......................................... 8

Add Fuel.................................................... 8

Attach NegativeBatteryCable................................... 8

System Ground .............................................. 9

Connectingto a Building's ElectricalSystem........................ 9

GeneratorLocation ........................................... 9

FeaturesandControls............................ 10

Cord Sets and Receptacles.................................... 11

Battery FloatCharger......................................... 11

Operation .................................... 12

Starting the Engine .......................................... 12

ConnectingElectrical Loads.................................... 13

Stopping the Engine.......................................... 13

Warm Weather Operation ..................................... 13

Don't OverloadGenerator ..................................... 14

Maintenance .................................. 15

MaintenanceSchedule........................................ 15

GeneratorMaintenance....................................... 15

Battery Maintenance ......................................... 15

Engine Maintenance.......................................... 16

Storage ................................................... 19

Troubleshooting ................................ 20

Warranties .................................... 21

Emissions Control System Warranty............................. 21

GeneratorOwnerWarranty .................................... 23

Specifications ................................. 24

Product Specifications........................................ 24

Common Service Parts ....................................... 24

Espa_ol

OperatorSafety

Equipment Description

Readthis manualcarefully and becomefamiliar

...... with yourgenerator. Knowitsapplications, its

limitationsand anyhazardsinvolved.

Thegeneratoris an engine-driven, revolvingfield, alternating

current (AC)generator. It was designedto supply electrical

power for operatingcompatible electricallighting, appliances,

tools and motor loads.Thegenerator's revolvingfield is

driven at about3,600 rpm by a single-cylinderengine.

NOTICE Exceedinggeneratorswattage/amperagecapacity

candamagegeneratorand/or electricaldevicesconnectedto

it.

• DONOTexceedthegenerator'swattage/amperagecapacity.See

Don'tOverloadGeneratorintheOperationsection.

Everyeffort hasbeen madeto ensurethat the information in

this manualis both accurateand current. However,the

manufacturer reservesthe right to change,alter or otherwise

improve the generatorand this documentation at anytime

without prior notice.

The EmissionControl Systemfor this generator is warranted

for standardsset by the Environmental ProtectionAgency

and the California Air Resources Board.

Important Safety Information

Themanufacturer cannotpossibly anticipateevery possible

circumstance that might involve a hazard.Thewarnings in

this manual, and the tags and decals affixedto the unit are,

therefore, not all-inclusive. If you usea procedure,work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also makesure that the

procedure, work method or operating technique that you

choose does not renderthe generator unsafe.

SafetySymbolsand Mleanings

ToxicFumes Kickback ElectricalShock

Fire

Explosion Operator'sManual

MovingParts FlyingObjects HotSurface

Thesafety alertsymbol indicatesa potential personal

injury hazard.A signalword (DANGER,WARNING,or

CAUTION)is usedwith the alert symbol to designatea

degreeor levelof hazardseriousness.A safety symbol may

be usedto representthe type of hazard.Thesignal word

NOTICEis usedto address practicesnot relatedto personal

injury.

_i, DANGER indicatesa hazardwhich, if not avoided, will

result in deathor serious injury.

_i, WARNINGindicatesa hazardwhich, if not avoided,

could result in death or serious injury.

_i, CAUTIONindicates a hazardwhich, if not avoided, could

result in minor or moderate injury.

NOTICEaddress practices not relatedto personal injury.

4 BRIGGSandSTRATTON.COIVl

Using a generator indoors CAN KiLL YOU iN MINUTES,

Generator exhaust contains carbon monoxide, This is

a poison you cannot see or smelJ,

V V

NEVER use inside a home

or garage, EVEN iF doors

and windows are open,

Only use OUTSIDE and

far away from windows,

doors, and vents,

_i, WARNING Runningengine gives off carbon

monoxide, an odorless, colorless, poison gas.

_ Breathing cancause headache,

carbon monoxide

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

• OperategeneratorONLYoutdoors.

• Installabatteryoperatedcarbonmonoxidealarmnearthe

bedrooms.

Keepexhaustgas from entering a confined areathrough

windows, doors, ventilation intakes,or other openings.

DO NOTstart or run engine indoors or in an enclosedarea,

(even if windows and doors areopen), including the generator

compartment of arecreationalvehicle (RV).

A, WARNING Theengine exhaustfrom this product

contains chemicals known to the State of California to

causecancer, birth defects,or other reproductive harm.

_i, WARNING Certain components in this product and

relatedaccessoriescontain chemicals known to the State

of Californiato causecancer, birth defects or other

reproductive harm. Wash hands after handling.

_i, WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand

_,_4 and arm toward engine faster than you can let

v-"

go.

Broken bones, fractures, bruises, or sprains could result.

• When starting engine,pull cord slowly until resistanceisfelt

andthen pull rapidly to avoid kickback.

• NEVERstart or stop enginewith electricaldevices plugged in

andturned on.

_i, WARNING Generator produces hazardous voltage.

')Jl|l Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

• When using generatorfor backup power, notify utility company.

Useapproved transfer equipment to isolate generator from

electric utility.

• Usea ground fault circuit interrupter (GFCI)in any damp or

highly conductive area,such asmetal deckingor steel work.

• DO NOTtouch barewires or receptacles.

• DO NOTuse generatorwith electrical cords which areworn,

frayed,bare or otherwise damaged.

• DO NOToperate generatorin the rain or wet weather.

• DO NOThandle generatoror electricalcords while standing in

water, while barefoot,or while hands or feet arewet.

• DO NOTallow unqualified personsor children to operate or

servicegenerator.

_i, WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe

burns or death.

WHENADDINGOR DRAININGFUEL

• Turn generatorOFFand let it cool at least2 minutes before

removing fuel cap. Loosencap slowly to relievepressure in

tank.

• Fill or drain fuel tank outdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• If fuel spills, wait until it evaporatesbefore starting engine.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigaretteor smoke.

WHENSTARTINGEQUIPMENT

• Ensurespark plug, muffler,fuel cap,andair cleanerarein place.

• DO NOTcrank enginewith spark plug removed.

WHENOPERATINGEQUIPMENT

• DONOTtip engine or equipmentat anglewhich causes fuel to

spill.

• This generator is not for use in mobile equipment or marine

applications.

WHENTRANSPORTING,MOVING OR REPAIRINGEQUIPMENT

• Transport/move/repair with fuel tank EMPTYor with fuel shutoff

valveOFF.

• DONOTtip engine or equipmentat anglewhich causes fuel to

spill.

• Disconnectspark plug wire.

WHENSTORINGFUELOR EQUIPMENTWITH FUELIN TANK

• Store awayfrom furnaces, stoves, water heaters,clothes

dryers, or other appliancesthat have pilot light or other ignition

source becausethey can ignitefuel vapors.

A WARNING

This generatordoes not meet U. S. CoastGuard Regulation

33CFR-183and should not beusedon marineapplications.

Failureto usethe appropriate U. S. CoastGuard approved

generator could result in death or serious injury and/or

property damage.

_i, WARNING Contact with muffler area can result in

serious burns.

_ _ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts andAVOID hot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sidesof

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engineon anyforest-covered,

brush-covered, or grass-covered land unlessthe exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained in effective working order. Other statesor

federal jurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a sparkarrester designedfor the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

_i, WARNING Unintentional sparking can result in fire or

,_¢ electric shock.

WHENADJUSTINGOR MAKINGREPAIRSTO YOURGENERATOR

• Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

• Use approvedspark plugtester.

• DO NOTcheckfor spark with spark plug removed.

_i, WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVERoperate generator without protective housing or covers.

• DO NOTwear looseclothing, jewelry or anythingthat may be

caught in the starter or other rotating parts.

• Tie up long hairand removejewelry.

_i, CAUTION Excessively high operating speeds increase

risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOTtamper with governedspeed. Generatorsupplies

correct rated frequency and voltage when running at governed

speed.

• DO NOTmodify generator in any way.

NOTICE Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOTexceedthe generator's wattage/amperagecapacity. See

Don't OverloadGeneratorinthe Operationsection.

• Start generator and letengine stabilize beforeconnecting

electrical loads.

• Connectelectrical loads in OFFposition, thenturn ONfor

operation.

• Turn electricalloads OFFanddisconnect from generator before

stopping generator.

NOTICE Improper treatment of generator can damage it

and shorten its life.

• Use generatoronly for intendeduses.

• If you havequestions about intended use,ask dealeror contact

local service center.

• Operategenerator only on levelsurfaces.

• DO NOTexposegenerator to excessivemoisture, dust, dirt, or

corrosive vapors.

• DO NOTinsert any objectsthrough cooling slots.

• If connected devicesoverheat, turn them off anddisconnect them

from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

6 BRIGGSandSTRATTON.COIVI

Assembly

F[-_-_I Read entireoperator'smanualbeforeyou attempt

toassemble or operateyournewgenerator.

Your generator requiressome assembly and is readyfor use

after it hasbeen properly servicedwith the recommended

fuel and oil levelis verified.

If you haveany problemswith the assemblyof your generator,

pleasecallthe generatorhelplineat (800) 743-4115. If calling

for assistance,pleasehavethe model, revision,and serial

numberfrom the identificationlabel available.Seegenerator

Featuresand Controlsfor identification labellocation.

UnpackGenerator

1. Setthe carton on a rigid, flat surface.

2. Removeeverything from carton exceptgenerator.

3. Opencarton completely by cutting eachcorner from

top to bottom.

4. Leavegeneratoron cartonto install wheel kit.

The generatoris suppliedwith:

• Operator's manual

• Batteryfloat charger

• Wheels (2)

• Axle

• Support leg

• Wheelkit hardware

Install Wheel Kit

NOTICE Wheelkit is not intendedfor over-the-road use.

You will needthe following toolsto install thesecomponents:

• 13 mm wrench

• Socketwrench with a 13 mm socket

• Pliers

• Safetyglasses

Install the wheel kit as follows:

1. Tip generatorso that engine end is up.

2. Slide axle (A) through both mounting brackets.

3. Slide a wheel (B) over axle.

NOTICE Besure to install wheelwith raised hub inboard.

4. Placea washer (C) on axleand then placean e-ring (D)

in axlegroove.

_i, CAUTION E-rings can causeeye injury.

E-rings can spring back and become airborne

when installing or removing.

• Alwaysweareyeprotectionwheninstalling/removinge-rings.

5. Install e-ring with pliers, squeezingfrom top of e-ring

to bottom of axle.

6. Repeatsteps 3 through 5 to secure secondwheel.

7. Return generatorto normal operating position (resting

on wheels).

8. Removehandle (H) from generatorframe by pushing in

pins (J) and pulling up on handle.

9. Turn handle around as shown below and attach it to

generatorframe by pushing in pins on generatorframe.

Slide handle down until pins lock into holeson handle.

10. Tip generatorso that engine side is down.

11. Line up holes in support leg (E) with holes in generator

frame.

12. Attach support leg using 2 capscrews(IVI8x 20 mm)

(F) and 2 hexnuts (G). Tightenwith a 13 mm socket

wrench and 13 mm wrench.

13. Return generatorto normal operating position (resting

on wheels and support leg).

NOTICE Turn the handle around on the generatorframe for

storage purposes ONLY.

VerifyEngineOil Level

Thegeneratorengine is shippedfrom thefactory filled with

oil (API SJor higher 10W-30).This allows for generator

operation in the widest rangeof temperatureand climate

conditions. Beforestarting the engine,check oil leveland

ensurethat engineis serviced asdescribed in Maintenance.

NOTICE See Oflin the Maintenancesectionto review oil

recomendations.Verify provided oil in engine is the correct

viscosity for current ambient temperature.

Cleanarea around fuel fill cap, remove cap.

Slowly add unleadedgasoline (A) to fuel tank (B). Be

careful not to fill abovethe baffle (C). This allows

adequatespace for fuel expansion asshown.

NOTICE Any attempt to crank or start the engine before it

has been properly filled with the recommendedoil will

result in equipmentfailure.

• Referto Maintenanceforoilfill information.

• Damagetoequipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

Add Fuel

Fuel mustmeet theserequirements:

• Clean,fresh, unleadedgasoline.

• A minimum of 87 octane/87AKI (91 RON).Forhigh

altitude use, seeHigh Altitude.

• Gasolinewith up to 10% ethanol (gasohol) or up to

15% MTBE(methyl tertiary butyl ether) is acceptable.

NOTICE Avoid generatordamage.

Failureto follow Operator's Manualfor fuel

recommendations voids warranty.

• DONOTuseunapprovedgasolinesuchasE85.

• DONOTmixoil in gasoline.

• DONOTmodifyengineto runonalternatefuels.

Toprotectthe fuelsystemfrom gum formation, mix in afuel

stabilizerwhenaddingfuel. SeeStorage.All fuel is not the

same.If you experiencestarting or performanceproblems after

usingfuel, switch to adifferentfuel provideror changebrands.

This engineiscertifiedto operateon gasoline.Theemission

control systemfor this engineis EM(EngineModifications).

_i, WARNING Fueland its vapors are extremely

flammable and explosive.

Fireor explosioncan causesevere

burns or death.

WHENADDINGFUEL

• Turn generator OFFand let it cool at least2 minutes before

removing fuel cap. Loosencap slowly to relievepressure in

tank.

• Fill fuel tank outdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• If fuel spills, wait until it evaporatesbefore starting engine.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigarette or smoke.

3. Install fuel capand let anyspilled fuel evaporatebefore

starting engine.

HighAltitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane/ 85 AKI (89 RON)gasoline is acceptable.To

remainemissions compliant, high altitude adjustment is

required.Operationwithout this adjustmentwill cause

decreasedperformance, increasedfuel consumption, and

increasedemissions. Seean authorized dealerfor high

altitude adjustment information. Operationof the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

Attach Negative Battery Cable

Your unit is equippedwith electric start capability, but canbe

started manually. If you choose not to use the electric start

feature,you do not needto connect the negative battery

cable.

Thesealedbattery on the generatorpre-installed exceptfor

the negative (black) batterycable.

_i, WARNING Batteryposts, terminals and related

accessoriescontain leadand leadcompounds - chemicals

known to the State of Californiato cause cancerand

reproductiveharm. Washhandsafter handling.

To install:

1. Cut off tie wrap securing looseend of negative (black)

cable.

Using an 8 mm wrench, remove screw (D), lock washer

(E) and flat washer (F) on negativebattery terminal.

8 BRIGGSandSTRATTON.COIVl

3. Slide lock washer,flat washer and negativebattery

cable (G) over screw.

4. Reattachscrew to negative batteryterminal and

tighten.

5. Verify that connections to battery and generatorare

tight and secure.

NOTICE Chargeprior to usefollowing the instructions in

the section Battery Float Charger.

SystemGround

Thegenerator hasa system ground that connectsthe

generatorframe componentsto the ground terminals on the

ACoutput receptacles.Thesystem ground is connected to

the ACneutral wire (the neutral is bonded to the generator

frame).

Special Requirements

Theremay beFederalor State OccupationalSafety and

Health Administration (OSHA)regulations, local codes, or

ordinances that applyto the intended useof the generator.

Pleaseconsult a qualified electrician, electrical inspector, or

the local agency havingjurisdiction:

• In some areas,generators are requiredto be registered

with local utility companies.

• If the generator is usedat a construction site, there

may be additional regulations which must be observed.

Connecting to a Building's Electrical System

Connectionsfor standby powerto a building's electrical

system must be made by a qualified electrician. The

connection must isolate the generator powerfrom utility

power and must comply with all applicablelaws and

electrical codes.

_i, WARNING Generatorproduces hazardousvoltage.

b,|l|z Failureto isolate generatorfrom power utility

can result in deathor injury to electric utility

workers due to backfeedof electrical energy.

• Whenusinggeneratorfor backuppower,notifyutilitycompany.

Useapprovedtransferequipmentto isolategeneratorfrom

electricutility.

• Useagroundfaultcircuitinterrupter(GFCI)in anydampor

highlyconductivearea,suchasmetaldeckingor steelwork.

• DONOTtouchbarewiresor receptacles.

• DONOTusegeneratorwithelectricalcordswhichareworn,

frayed,bareor otherwisedamaged.

• DONOToperategeneratorintherainorwetweather.

• DONOThandlegeneratoror electricalcordswhilestandingin

water,whilebarefoot,or whilehandsorfeetarewet.

• DONOTallowunqualifiedpersonsorchildrento operateor

servicegenerator.

GeneratorLocation

Clearancesand Air Movement

_i, WARNING Exhaustheat/gases can ignite

combustibles, structures or damagefuel tank

causing a fire.

• Keepat least5 ft. (152 cm) clearanceon all sidesof generator

including overhead.

Placegeneratoroutdoors in anareathat will not accumulate

deadlyexhaust gas. DONOTplacegeneratorwhere exhaust

gas (A) could accumulate and enter inside or be drawn into

a potentially occupied building. Ensureexhaustgas is kept

awayfrom any windows, doors, ventilation intakes, or other

openings that canallow exhaustgasto collect in aconfined

area.Prevailingwinds and air currents should betaken into

consideration when positioning generator.

Using a generator indoors CAN KiLL YOU iN MINUTES,

Generator exhaust contains carbon monoxide, This is

a poison you cannot see or smell,

V V

NEVER use insidea home

or garage, EVENIF doors

and windows areopen,

Only use OUTSIDE and

far away from windows,

doors, and vents,

FeaturesandControls

Readthis Operator'sManual and safetyrules beforeoperatingyourgenerator.

Comparethe illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Savethis manual for future reference.

A- FuelTank -- Capacityof six (6) U.S.gallons.

B- RockerSwitchCircuitBreaker-- The120/240 Volt AC,

30A lockingreceptacleisprovided with a rocker switch

circuit breakerto protect the generatoragainst electrical

overload.

C- Oil Fill Cap-- Checkand add engine oil here.

D - Oil Drain Plug-- Drainengine oil here.

E - 120 Volt AC,20 Amp, DuplexReceptacles-- May be

usedto supply electrical powerfor the operation of

120 Volt AC,20 Amp, single phase,60 Hz electrical,

lighting, appliance, tool and motor loads.

F - 120/240 Volt AC,30 Amp LockingReceptacle-- May

be usedto supply electrical power for the operation of

120 and/or 240 Volt AC,30 Amp, single phase,60 Hz

electrical, lighting, appliance,tool and motor loads.

G - CircuitBreakers(AC)--The 120 Volt AC, 20A duplex

receptaclesare provided with "pushto reset"circuit

breakersto protect the generatoragainst electrical

overload.

H - GroundingFastener-- Consultyour local agency having

jurisdictionfor grounding requirements in your area.

J - IdentificationLabel-- Provides model, revision and

serial number of generator. Pleasehavethese readily

availablewhen calling for assistance.

K- SparkArresterMuffler -- Exhaustmuffler lowers engine

noiseand is equippedwith aspark arrester screen.

L - Air Cleaner -- Protects engine by filtering dust and

debris out of intake air.

M - EngineIdentification-- Provides model, type and code

of engine. Pleasehavethese readilyavailableif calling

for assistance.

N - Recoil Starter-- Used to start the engine manually.

P - EngineRockerSwitch-- Setthis switch to "On"before

using recoil starter. Set switch to "Off"to switch off

engine.

R - ChokeLever- Usedwhen starting a cold engine.

S- FuelValve-- Usedto turn fuel supply on and off to

engine.

T - StartButton-- Pushand hold instart position for a

maximum of 15 seconds during eachstart attempt, until

engine starts.

U - BatteryFloatChargerJack-- Use batteryfloat charger

to keepthe starting battery charged and readyfor use.

10 BRIGGSandSTRATTON.COM

CordSetsandReceptacles

Use only high quality, well-insulated, grounded extension

cords with the generator's 120 Volt duplex receptacle.

Inspect extensioncords before eachuse.

Checkthe ratings of all extensioncords beforeyou use

them. Extensioncord sets usedshould be ratedfor 125 Volt

ACloads at 20 Amps or greaterfor most electrical devices.

Somedevices, however, may not require this type of

extension cord. Checkthe operator's manuals of those

devicesfor the manufacturer's recommendations.

Keepextension cords asshort aspossible to minimize

voltage drop.

A double pole rocker switch circuit breakeris providedto

protect the locking receptacle.If this circuit breakeris

tripped, all panel receptaclesaredisconnected.

_iLWARNING Overloadedelectrical cords can overheat,

arc, and burn resulting in death, bodily injury,

and/or property damage.

• ONLYusecordsratedfor yourloads.

• Followallsafetiesonelectricalcords.

120/240 Volt AC,30 Amp, LockingReceptacle

Use a NEIVIAL14-30 plugwith this receptacle.Connecta

4-wire cord set ratedfor 250 Volt AC loadsat 30 Amps (or

greater). You can usethe same4-wire cord if you plan to

run a 120 Volt load.

4-Wire Cord Set

(Neutral)

Y(Hot) | X(Hot)

NEMA L14-30 /--/L7 Ground (Green)

This receptaclepowers 120/240 Volt AC, 60 Hz,single phase

loads requiring up to 6,200 watts of power (6.2 kW) at

25.8 Amps for 240 Volts or two independent 120 Volt loads

at 25.8 Amps each. Theoutlet is protected by a two pole

rocker switch circuit breaker.

120 Volt AC, 20 Amp, DuplexReceptacles

Eachduplex receptacleis protectedagainst overloadby a

push-to-reset circuit breaker.

Useeachreceptacleto operate120 Volt AC, single-phase,

60 Hz electricalloads requiring up to 2,400 watts (2.4 kW) at

20 Amps of current. Usecord setsthat are ratedfor 125 Volt

ACloads at 20 Amps (or greater). Inspectcord sets before

eachuse.

BatteryFloatCharger

Usebatteryfloat chargerjack to keepthe starting battery

chargedand readyfor use. Battery charging should be done

in a dry location, such as insidea garage.

1. Plug charger into unit's "Battery FloatCharger"jack,

which is located next to the start switch. Plug battery

charger into a 120 Volt ACwall receptacle.

NOtiCE

Unplug charger from unit and wall outlet when

generator is being started and while it is in operation.

Keepthis charger plugged in when generator is not in

useto prolong battery life. The chargerhas a built in

float equalizerand will not overchargethe battery, even

when plugged in for an extended period of time.

SeeBattery Maintenancefor additional information.

NOTICE Receptacles may be marked with rating value

greater than generator output capacity.

• NEVERattempt to power adevice requiring more amperagethan

generator or receptaclecan supply.

• DONOToverloadthe generator.SeeDon't OverloadGenerator.

Operation

Starting the Engine

Disconnect all electrical loads from the generator. Usethe

following start instructions (seeFeaturesand Controlsfor

location of controls described below):

1. Make sure unit is on a levelsurface.

NOTICE Failureto start and operatethe unit on a level

surfacewill causethe unit not to start or shut down during

operation.

2. Turn fuel valve(A) to "On" position.

3. Pushchoke leverto "Choke" position (N).

4. Pushengine rocker switch (B) to "On" position.

5A.

Forelectricstarting, push and hold the start button in

start position until generatorstarts. To prolong the life

of starter components, DONOThold start switch in

start position for more than 15 seconds, and pausefor

at least1 minute betweenstarting attempts.

RUN START

• If engine starts, proceedto step 7.

• If engine fails to start, proceedto step 6.

NOTICE If battery is discharged, use manualstarting

instructions.

5B.

Formanualstarting, grasp recoil handle and pull

slowly until slight resistanceisfelt. Then pull rapidly

one time only to start engine.

• If engine starts, proceedto step 7.

• If engine fails to start, proceedto step 6.

A WARNING Starter cord kickback(rapid retraction) can

result in bodily injury. Kickbackwill pull hand

_,_ and arm toward enginefasterthan you can let

go.

Brokenbones,fractures, bruises, or sprains could result.

• Whenstartingengine,pullcordslowlyuntilresistanceisfelt

andthenpull rapidlytoavoidkickback.

• NEVERstartor stopenginewith electricaldevicespluggedin

andturnedon.

6. Move choke leverto "Half" choke position, and pull

recoil handletwice.

• If engine fails to start, repeatsteps 5 thru 7.

7. Slowly move choke leverto "Run" position (1_,1).If

engine falters, move choke leverto "Half" choke

position until engine runs smoothly, andthen to "Run"

position (1+1).

NOTICE If engine floods, placechoke lever in "Run"

position (I{ i) and crank until engine starts.

NOTICE If engine starts after 3 pulls but fails to run, or if

unit shuts down during operation, makesure unit is on a

level surfaceand check for proper oil level in crankcase.This

unit may be equipped with a low oil protection device. If so,

oil must be at proper levelfor engine to start.

A WARNING Contact with muffler area can result in

serious burns.

_ _ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts andAVOIDhot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

generator including overhead.

• It is aviolation of California Public Resource Code,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federaljurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain aspark arrester designedfor the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

12 BRIGGSandSTRATTON.COM

Connecting Electrical Loads

1. Let engine stabilizeand warm upfor a few minutes

after starting.

2. Ensurecircuit breakeron control panelis in "On"

position.

3. Plug in andturn on the desired 120 and/or 240 Volt

AC,single phase,60 Hz electrical loads.

NOTICE When plugging into the 120 Volt receptacles,plug

items to be powered in sequenceasshown below.

NOTICE

• DONOTconnect 240Volt loads to the 120 Volt duplex

receptacles.

• DONOTconnect 3-phaseloads to the generator.

• DONOTconnect 50 Hzloads to the generator.

• DONOTOVERLOADTHEGENERATOR.SeeDon't

OverloadGenerator.

NOTICE Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOTexceedthe generator's wattage/amperagecapacity. See

Don't OverloadGeneratorinthe Operationsection.

• Start generator and let engine stabilize beforeconnecting

electrical loads.

• Connectelectrical loads in OFFposition, thenturn ONfor

operation.

• Turn electricalloads OFFand disconnectfrom generator before

stopping generator.

Stopping the Engine

1. Turn OFFand unplug all electrical loads from generator

panel receptacles.NEVERstart or stop enginewith

electrical devicesplugged in andturned ON.

2. Let engine run at no-load for several minutes to

stabilize internaltemperatures of engine and generator.

3. Push engine rocker switch to "Off" position.

_i, WARNING Backfire,fire or enginedamagecould

occur.

• DONOTstop engineby moving chokecontrol to "Choke"

position (b,I).

4. Move fuel valve to "Off" position.

Warm Weather Operation

This generatorengine is equippedwith WeatherGuard,an

innovativefeature to preventcarburetor icing in cold weather

conditions. WeatherGuardhas beenengineeredto operatein

all weather conditions. However,product performancecan be

increasedwhen operatingthe generator solely in warm

weather by removing the WeatherGuardshield (A).

Removethe two nuts (B) and loosenthe fastener(C) as

shown. Store shield andfastenersfor future coldweather

operation.

Don't Overload Generator

Capacity

You must make sureyour generator cansupply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Selectthe itemsyou will power at the same time.

2. Totalthe rated(running) watts ofthese items. This is the

amount of poweryour generatormust produceto keep

your items running. SeeWattageReferenceGuide.

3. Estimatehow many surge (starting) watts you will need.

Surge wattageis the short burst of power neededto

start electric motor-driven tools or appliancessuch asa

circular saw or refrigerator. Becausenot all motors start

atthe sametime, total surgewatts can be estimatedby

adding only the item(s) with the highest additionalsurge

watts to thetotal ratedwatts from step 2.

Example:

ToolorAppliance

WindowAir

Conditioner

Refrigerator

DeepFreezer

Television

Light(75Watts)

Watts

1200

800

500

3075Total

RunningWatts

Total Rated(Running) Watts

HighestAdditional Surge Watts

Total GeneratorOutput Required

(Starting)Watts

1800

1600

5OO

1800Highest

SurgeWatts

= 3075

= 1800

=4875

Power Management

To prolong the life of your generatorand attacheddevices, it

is important to take carewhen adding electrical loadsto your

generator. Thereshould be nothing connectedto the

generator outlets before starting its engine.Thecorrect and

safe way to managegeneratorpower isto sequentiallyadd

loads asfollows:

1. With nothing connectedto the generator,start the

engine asdescribed inthis manual.

2. Plug in andturn on the first load, preferablythe largest

load you have.

3. Permit the generatoroutput to stabilize (engine runs

smoothly and attacheddeviceoperates properly).

4. Plug in andturn on the next load.

5. Again, permit the generatorto stabilize.

6. Repeatsteps 4 and 5 for eachadditional load.

NEVERadd more loads than the generatorcapacity.Take

special careto consider surge loads in generator capacity,as

described above.

ToolorAppliance

Rated* Additional

(Running) Surge (Starting)

Watts Watts

Essentials

Light Bulb - 75 watt 75

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer- 18 Cu.R. 800 1600

WaterWell Pump - 1/3 HP 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

FurnaceFanBlower- 1/2 HP 800 1300

Kitchen

Microwave Oven- 1000 Watt 1000

CoffeeMaker 1500

Electric Stove - Single Element 1500

Hot Plate 2500

Family Room

DVD/CDPlayer 100

VCR 100

Stereo Receiver 450

Color Television - 27" 500

PersonalComputerw/17" monitor 800

Other

Security System 180

AM/FM Clock Radio 300

GarageDoorOpener- 1/2 HP 480 520

Electric Water Heater- 40 Gallon 4000

DIf/Joh Site

Quartz HalogenWork Light 1000

Airless Sprayer - 1/3 HP 600 1200

Reciprocating Saw 960 960

Electric Drill- 1/2 HP 1000 1000

Circular Saw- 7 1/4" 1500 1500

Miter Saw- 10" 1800 1800

Table Planer- 6" 1800 1800

TableSaw/RadialArm Saw- 10" 2000 2000

Air Compressor- 1-1/2 HP 2500 2500

* Wattageslisted areapproximate only. Checktool

appliancefor actual wattage.

14 BRIGGSandSTRATTON.COM

Maintenance

MaintenanceSchedule

Follow the hourly or calendarintervals, whichever occurs

first. More frequent serviceis required when operating in

adverseconditions noticed below.

• Changeengine oil

• Cleandebris

• Checkengineoil level

• Service engineair cleaner'

• Changeengine oiP

• Service spark plug

• Inspect muffler and spark arrester

• Cleancooling system'

• Checkvalve clearance

1 Service more often under dirty or dusty conditions.

GeneralRecommendations

Regular maintenancewill improve the performance and

extend the life of the generator. Seeany authorizeddealer for

service.

Thegenerator's warranty doesnot cover items that have

been subjectedto operator abuseor negligence.To receive

full valuefrom the warranty, the operator must maintain the

generator asinstructed inthis manual.

Someadjustments will needto be made periodically to

properly maintain your generator.

All serviceand adjustments should be made at least once

eachseason.Follow the requirementsin the Maintenance

Schedulechart above.

NOTICE Oncea year you should cleanor replacethe spark

plug and replacethe air filter. A new spark plug and cleanair

filter assure proper fuel-air mixture and helpyour engine run

better and last longer.

EmissionsControl

Maintenance, replacement,or repair of theemissions

controldevicesand systemsmay be performedby any

non-roadengine repair establishmentor individual.

However,to obtain "no charge" emissions control service,

the work must be performed by a factory authorizeddealer.

Seethe Emissions Warranty.

GeneratorMaintenance

Generatormaintenanceconsists of keepingthe unit clean

and dry. Operateand store the unit in a clean dry

environment where it will not be exposedto excessivedust,

dirt, moisture, or any corrosive vapors. Coolingair slots in

the generator must not become cloggedwith snow, leaves,

or any other foreign material.

NOTICE DONOTusewater or other liquids to clean

generator. Liquids canenter engine fuel system, causing

poor performance and/or failure to occur. In addition, if

liquid enters generator through cooling air slots, someof the

liquid will be retainedin voids and cracksof the rotor and

stator winding insulation. Liquid and dirt buildup on the

generator internalwindings will eventuallydecreasethe

insulation resistanceof these windings.

Cleaning

Dailyor before use, look around and underneaththe

generatorfor signs of oil or fuel leaks. Cleanaccumulated

debris from inside and outside the generator. Keepthe

linkage, spring and other engine controls clean. Keepthe

areaaround and behind the muffler free from any

combustible debris. Inspect cooling air slots andopenings

on generator. Theseopenings must be kept cleanand

unobstructed.

Engine parts should be kept cleanto reducethe risk of

overheating and ignition of accumulateddebris:

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of generator can damage it

and shorten its life.

• DO NOTexposegenerator to excessivemoisture, dust, dirt, or

corrosive vapors.

• DONOTinsert any objects through cooling slots.

• Use a soft bristle brush to loosen cakedon dirt or oil.

• Use a vacuum cleanerto pick uploose dirt and debris.

BatteryMaintenance

Otherthan float charging, described elsewhere,no

maintenanceis requiredfor the starting battery. Keepthe

battery and terminals cleanand dry.

NOTICE Batterycharging should be performed in adry

location, such as inside a garage.

A. WARNING Batteryposts, terminals and related

accessoriescontain leadand leadcompounds - chemicals

known to the State of Californiato cause cancerand

reproductiveharm. Washhandsafter handling.

EngineMaintenance

A. WARNING Unintentionalsparking can result infire or

,_¢ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOUR

GENERATOR

• Disconnectthesparkplugwirefromthesparkplugandplace

thewirewhereit cannotcontactsparkplug.

WHENTESTINGFORENGINESPARK

• Useapprovedsparkplugtester.

• DONOTcheckfor sparkwith sparkplugremoved.

Oil

Oil Recommendations

We recommendthe useof Briggs & Stratton Warranty

Certified oils for best performance.Otherhigh-quality

detergent oils are acceptableif classified for serviceSF, SG,

SH, SJ or higher. DONOTuse specialadditives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Usethe chart to select the best viscosity for the

outdoor temperature rangeexpected.

1046886"---__l-- __ _ --o_'

5O N

32 2

-4

-22 _

°C

o__"_ 20304010

-10

-20

-30

* Below 40°F (4°C) the use of SAE30 will result in hard starting.

** Above 80°F (27°C) the useof 10W30 may causeincreased oil

consumption. Checkoil level more frequently.

O OTICE Synthetic oil meeting ILSACGF-2,API

certification mark and API servicesymbol with

"SJ/CF ENERGYCONSERVING"or higher, is an

acceptableoil at alltemperatures. Useof synthetic

oil does not alter required oil changeintervals.

CheckingOil Level

Oil levelshould be checked prior to each useor at least

every 8 hours of operation. Keepoil levelmaintained.

1. Make sure generatoris on alevelsurface.

2. Cleanarea around oil fill and remove oil fill cap.

3. Verify oil is at the point of overflowing at oil fill

opening.

4. Replaceand tighten oil fill cap.

AddingEngineOil

1. Make sure generatoris on alevelsurface.

2. Checkoil levelas described in CheckingOilLevel

3. If needed,slowly pour oil into oil fill opening to the

point of overflowing at oil fill.

4. Replaceand tighten oil fill cap.

ChangingEngineOil

If you are usingyour generator under extremely dirty or

dusty conditions, or in extremelyhot weather, changethe oil

more often.

A. CAUTION Avoid prolonged or repeated skin contact

with used motor oil.

• Used motor oil has beenshown to causeskin cancer in certain

laboratory animals.

• Thoroughly wash exposed areaswith soapand water.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOIL TOCOLLECTIONCENTERS.

Changethe oil while the engine is still warm from running,

asfollows:

Make sure unit is on alevelsurface.

Disconnectthe spark plug wire from the sparkplug and

placethe wire where it cannot contact spark plug.

Cleanarea around oil drain plug (A). The oil drain plug

is located at baseof engine,opposite carburetor.

16 BRIGGSandSTRATTON.COIVl

4. Removeoil drain plug and drain oil completely into a

suitable container.

5. Reinstall oil drain plug andtighten securely. Removeoil

fill cap.

6. Slowly pour oil (about 28 oz.) into oil fill opening (B) to

the point of overflowing (C) at oil fill cap. DONOT

overfill.

7. Reinstall oil fill cap. Fingertighten cap securely.

8. Wipe up any spilled oil.

Service Air Cleaner

Your enginewill not run properly and may be damaged if

you run it with a dirty air cleaner. Replacemore often if

operating under dirty or dusty conditions.

To servicethe air cleaner,follow thesesteps:

1. Loosen screws (D) and remove air cleanercover (E).

2. Carefully removecartridge (F) from base(G).

3. Install clean(or new) air cleanerassembly insidecover.

Disposeof old filter properly.

4. Assembleair cleanercover onto baseand tighten

screws.

Service Spark Plug

Changingthe spark plugwill helpyour engine to start easier

and run better.

1. Cleanarea around spark plug.

2. Removeand inspect spark plug.

3. Checkelectrode gapwith wire feeler gauge and reset

spark plug gap to recommended gap if necessary(see

Specifications).

4. Replacespark plug if electrodesare pitted, burned or

porcelain is cracked. Use the recommended

replacementspark plug. SeeSpecifications.

5. Install spark plug and tighten firmly.

InspectMufflerand Spark Arrester

Inspect the muffler for cracks,corrosion, or other damage.

Removethe spark arrester, if equipped,and inspectfor

damageor carbon blockage. If replacementparts are

required, make sureto useonly original equipment

replacementparts.

_lL WARNING Contact with muffler area can result in

serious burns.

_ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts andAVOIDhot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

generator including overhead.

• It is aviolation of California Public Resource Code,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federaljurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain aspark arrester designedfor the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

Cleanand inspectthesparkarresteras follows:

1. To remove muffler heatshield (A) from muffler (B),

removefour screws that connect guard to muffler

bracket.

Removefour screws that attach spark arrester screen

(C).

Inspect screenand obtain a replacementif torn,

perforated or otherwise damaged. DONOTusea

defective screen.If screenis not damaged,clean it with

commercial solvent.

4. Reattachscreen and muffler guard.

CleanCoolingSystem

Overtime debris may accumulate in cylinder cooling fins and

cannot be observedwithout partial engine disassembly. For

this reason,we recommendyou havean authorized service

dealer cleanthe cooling system (D) per recommended

intervals (see MaintenanceSchedulein the Maintenance

section). Equallyimportant is to keeptop of engine freefrom

debris. Also seeCleaning.

CheckValve Clearance

Regularvalve clearancecheck and adjustment will improve

performance and extend enginelife.This procedure cannot

be done without partial engine disassemblyand the useof

special tools. Forthis reasonwe recommendthat you have

an authorized Service Dealercheck and adjust valve

clearanceat recommended intervals (seeMaintenance

Schedulein the Maintenancesection).

CarburetorAdjustment

Thecarburetor on this engineis low emission. It is equipped

with a non-adjustableidle mixture valve.Top speedhas been

set atthe factory. If adjustment is required,seean

authorized servicedealer.

_k CAUTION Excessively high operating speeds increase

risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOTtamper with governed speed. Generatorsupplies

correct rated frequency and voltage when running at governed

speed.

• DO NOTmodify generator in any way.

18 BRIGGSandSTRATTON.COIVl

Storage

Thegenerator should be started at least once every seven

days and allowed to run at least30 minutes. If this cannot be

done and you must store the unit for more than 30 days,use

the following guidelinesto prepare it for storage.

GeneratorStorage

• Cleanthe generator as outlined in Cleaning.

• Checkthat cooling air slots and openingson generator

are open and unobstructed.

LongTerm StorageInstructions

Fuelcan becomestale when stored over 30 days.Stalefuel

causesacid and gum deposits to form in the fuel system or

on essentialcarburetor parts. To keepfuel fresh, use Briggs

& Stratton FRESHSTART®fuel stabilizer, availableasa

liquid additive or a drip concentrate cartridge.

Thereis no needto drain gasolinefrom the engine if a fuel

stabilizer is added according to instructions. Runthe engine

for 2 minutes to circulate the stabilizerthroughout the fuel

system. The engine andfuel canthen be stored upto

24 months.

If gasoline in the engine hasnot beentreated with a fuel

stabilizer, it must be drained into an approvedcontainer. Run

the engine until it stops from lack of fuel. The useof a fuel

stabilizer in the storage container is recommendedto

maintain freshness.

_i, WARNING Fueland its vapors are extremely

flammable and explosive.

Fireor explosioncan causesevere

burns or death.

WHENSTORINGFUELOREQUIPMENTWITHFUELINTANK

• Store awayfrom furnaces, stoves, water heaters,clothes dryers

or other appliances that have pilot light or other ignition source

becausethey can ignite fuel vapors.

WHENDRAININGFUEL

• Turn generator OFFand let it cool at least2 minutes before

removing fuel cap. Loosencap slowly to relievepressure in

tank.

• Drain fuel tank outdoors.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DO NOTlight acigarette or smoke.

ChangeEngineOil

While engine is still warm, drain oil from crankcase.Refill

with recommendedgrade.See ChangingEngine Oil.

OtherStorageTips:

1. DONOTstore fuel from one seasonto another unless it

has beentreated as describedin Long TermStorage

Instructions.

2. Replacefuel container if it starts to rust. Rustand/or

dirt in fuel can causeproblems if it's usedwith this

unit.

3. Cover unit with a suitable protective coverthat does not

retain moisture.

_i, WARNING Storagecovers can be flammable.

• DONOTplaceastoragecoverovera hotgenerator.

• Letequipmentcoolfor a sufficienttimebeforeplacingthecover

ontheequipment.

4. Store generator in clean, dry area.

Troubleshooting

Problem

Engineis running,butno AC

outputis available.

Cause

1. Oneof the circuit breakers is open.

2. Fault in generator.

3. Poor connection or defective cord set.

4. Connecteddeviceis bad.

Enginerunsgoodat no-loadbut

"bogs down"when loadsare

connected.

Enginewill not start;or starts

and runsrough;or shutsdown

when running.

1. Short circuit in a connectedload.

2. Enginespeed is too slow.

3. Generatoris overloaded.

4. Shorted generatorcircuit.

1. Engine rocker switch set to "Off"

position.

2. FuelValveis in "Off" position.

3. Low oil level.

Correction

1. Resetcircuit breaker.

2. Contact authorized servicefacility.

3. Checkand repair.

4. Connectanother devicethat is in good

condition.

1. Disconnect shorted electrical load.

2. Contact authorized servicefacility.

3. See Don't OverloadGeneratorin

Operationsection.

4. Contact authorized servicefacility.

1. Set engine rocker switch to

Enginelackspower.

4. Dirty air cleaner.

5. Out of fuel.

6. Stalefuel.

7. Spark plug wire not connectedto spark

"On'position.

2. Turn fuel valve to "On" position.

3. Fill crankcaseto proper levelor place

generator on level surface.

4. Cleanor replaceair cleaner.

5. Fill fuel tank.

6. Drain fuel tank and carburetor; fill with

fresh fuel.

Engine"hunts" or falters.

plug.

8. Bad spark plug.

9. Water in fuel.

10. Flooded.

11. Excessivelyrich fuel mixture.

12. Intakevalve stuck open or closed.

13. Engine haslost compression.

14. Cloggedcarbon canister.

1. Loadis too high.

7. Connectwire to spark plug.

8. Replacespark plug.

9. Drain gastank and carburetor; fill with

fresh fuel.

10. Wait 5 minutes and re-crankengine.

11. Contact authorized servicefacility.

2. Dirty air filter.

Carburetor is running too rich or too lean.

12. Contact authorized servicefacility.

13. Contact authorized servicefacility.

14. Replacecarbon canister.

1. See Don't OverloadGeneratorin

Operationsection.

2. Replaceair filter.

Contact authorized servicefacility.

20 BRIGGSandSTRATTON.COIVl

Page is loading ...

Briggs & Stratton 030452-0 Owner's manual

Brand: Briggs & Stratton

Model: 030452-0

Category: Power generators

Type: Owner's manual

This manual is also suitable for

30452

Download PDF

report

in other languages

español: Briggs & Stratton 030452-0 El manual del propietario

Briggs & Stratton 030452-0 Owner's manual

This manual is also suitable for

Briggs & Stratton 030452-0 Owner's manual

in other languages

Related papers

Other documents