Columbia THERAPEDIC 2500 Instructions For Use Manual

Brand: Columbia

Model: THERAPEDIC 2500

Category: Car seat

Type: Instructions For Use Manual

This manual is also suitable for

THERAPEDIC 2000

Therapedic™ Positioning Restraint System

Model #2000 and Model #2500

Instructions for Use

MODEL #2000: Use only with individuals who weigh

between 20 and 102 pounds (9.1 - 46.3 kg) and whose

height is less than 60 inches (152.4 cm).

MODEL #2500: Use only with individuals who weigh

between 40 and 130 pounds (18.1 - 59.0 kg) and whose

height is 54 – 66 inches (137.2 – 167.6 cm).

Important Safety Information ................................................... Page 3

Vehicle Seat Belt Compatibility ................................................ Page 6

Vehicle Seat Positions .............................................................. Page 7

Therapedic™ Features .............................................................. Page 8

Installation Instructions .......................................................... Page 10

Vehicle Lap and Shoulder Belt (Recommended) ............... Page 10

Vehicle Lap and Shoulder Belt—Requires Locking Clip ..... Page 11

Vehicle Lap Belt Only ......................................................... Page 13

Aircraft Installation (#2000 IPS only) .................................. Page 14

Installing the Tether Strap ...................................................... Page 15

Latch Vehicle Installation .................................................... Page 16

Non-Latch Vehicle Installation ............................................ Page 18

Components and Adjustments .............................................. Page 19

Operating the Harness Buckle ............................................ Page 19

Checking the Harness Height ............................................. Page 20

Adjusting the Harness Height ............................................. Page 20

Adjusting the Harness Fit ................................................... Page 20

Adjusting the Chest Clip ..................................................... Page 21

Adjusting the Head Pads .................................................... Page 21

Adjusting Lateral Positioning Pads ..................................... Page 21

Optional Accessories .............................................................. Page 22

Seat Depth Extender .......................................................... Page 22

Extensor Thrust Wedge ...................................................... Page 22

Swing-Away Abductor ........................................................ Page 22

ShurShape™ Custom Inserts ............................................. Page 23

Block Style Positioning Pads .............................................. Page 23

BuckleGuard ....................................................................... Page 23

Therapedic Explorer Mobility Base ..................................... Page 23

Securing the User in the Restraint ........................................ Page 24

Care and Maintenance ............................................................ Page 25

Removing the Cover ........................................................... Page 25

Refitting the Cover .............................................................. Page 25

Cleaning the Fabric ............................................................ Page 25

Cleaning the Harness and Buckle ...................................... Page 26

Copy of Registration Card ...................................................... Page 27

Table of Contents

Copy of Registration Card

Please promptly fill out and return the attached card.

Although child restraint systems undergo testing and evaluation, it

is possible that a child restraint could be recalled.

In case of recall, we can reach you only if we have your name

and address, so send in the attached card to be on our recall list.

In order to properly register your child restraint system, you will

need to provide the model number, serial number and date of

manufacture. This information is provided on the attached card.

Please fill out and mail this card NOW!

FOR YOUR CHILD’S CONTINUED SAFETYFOR YOUR CHILD’S CONTINUED SAFETYFOR YOUR CHILD’S CONTINUED SAFETY

Please fill in your name and address.

Name:

Address:

City: State: Zip:

Email: (optional)

Therapedic™ Registration Card

Tear off and mail this part.

Manufactured in Santa Fe Springs, CA USA

Date of Manufacture: /

Therapedic™ Positioning Restraint System

Sticker with model name, model

number and serial number.

Cleaning the Harness and Buckle

 The harness straps may be cleaned by sponging them with warm

water and a mild detergent.

 The buckle may be cleaned with a damp cloth and mild detergent.

 Towel dry — make sure the that harness and buckle are completely

dry before reinstalling.

 DO NOT bleach, machine wash or machine dry.

 DO NOT disassemble the harness.

 DO NOT use abrasive cleaners.

IMPORTANT

In case of a recall, we can reach you only if we

have your name and address. You MUST send

in the attached card to be on our recall list.

The postage is paid.

Do it today!

Please complete and return the owner registration card with-

in 30 days of purchase. This registration card is attached to

the shoulder strap of the Positioning Restraint System. A

sample of the registration card is shown below.

WARNING!

DEATH OR SERIOUS

INJURY can occur:

MODEL #2000: Use only with individuals who weigh between 20 and

102 pounds (9.1— 46.3 kg) and whose height is less than 60

inches (152.4 cm).

MODEL #2500: Use only with individuals who weigh between 40 and

130 pounds (18.1 — 59.0 kg) and whose height is

54 – 66 inches (137.2 – 167.6 cm).

 Snugly adjust the belts provided with this Positioning Restraint

System around the user. A snug strap should not allow any slack.

It lies in a relatively straight line without sagging. It does not press

on the user’s flesh or push the user’s body into an unnatural

position.

 Secure the top anchorage strap (tether) provided with this

Positioning Restraint System.

 Secure this Positioning Restraint System with your vehicle's seat

belt.

 Read and follow all instructions on this Positioning Restraint

System and in the written instructions located on the side of the

restraint.

 This Positioning Restraint System is designed to fit a wide range of

individuals. To ensure a proper fit for the user, it is important that

the restraint be correctly set up and installed before using it for the

first time.

 Use this Positioning Restraint System in the forward-facing position

only. This restraint is not designed for use in a rear-facing position.

The American Academy of Pediatrics recommends forward facing

only after one year old.

 Do not use this Positioning Restraint System with your vehicle's

lower anchor LATCH connector system. Use only the vehicle’s

seat belts for installation. Upper LATCH anchor points are used to

secure the tether.

 Do not use this Positioning Restraint System in the front seat

of a vehicle with a passenger air bag unless the air bag is

turned off. DEATH or SERIOUS INJURY can occur. According

to accident statistics, individuals are safer when properly restrained

in the rear seat than in the front seat. Regardless of seating

position, the Federal government recommends that all children

under twelve years of age ride in the rear seat.

 When using this Positioning Restraint System in a vehicle with side

air bags, refer to the vehicle owner’s manual for child restraint

installation instructions and precautions.

 Do not use this Positioning Restraint System with vehicle seats that

face to the side or rear or with vehicle seats with backs that can fold

forward in a crash or sudden stop. Check your owner's manual or

with your dealer if you are not sure.

 Read the section on vehicle seat belt compatibility to determine

the type of seat belts that may be used with this Positioning

Restraint System.

 Do not route the vehicle seat belt over the user while using this

Positioning Restraint System.

Cleaning Instructions

Removing the Cover

 Remove the head pads and positioning pads (if present) by

releasing the lanyards from the back of the restraint system.

 Remove the foam blocks from the head pads.

 Remove the head pad lanyard, by pressing the button on the plastic

ball on the inside of the restraint and removing it from the lanyard.

Then remove the lanyard from the outside of the restraint shell.

 Remove the harness completely by locating the metal bracket

securing the top of the harness along the back side of the restraint.

Pull it away to expose 3"- 4" of webbing. Turn the metal bracket so

the short side will fit through the slot in the back of the restraint and

push it through the slot and the cover.

 Repeat procedure above for the two shoulder straps and two lap

straps.

 Remove the cover by lifting the edges of the cover over the shell of

the restraint.

Refitting the Cover

 The cover, harness and pads can be reinstalled by following the

instructions above in reverse order.

Cleaning the Fabric

 The cover, head pad covers, positioning pad covers (if present) and

shoulder pads may be washed. It is recommended that you do not

wash these items with other items.

 Hand wash or machine wash on the “gentle” cycle with a mild

detergent. Water temperature should be “cold”.

 Do not use bleach.

 Machine dry using the lowest-heat cycle (e.g. “fluff”). Make sure all

fabric components are dry before reinstalling them on the restraint.

 Do not iron.

Care and Maintenance

Once the Therapedic™ Positioning Restraint System has been properly

fitted and installed in the vehicle, follow these instructions to secure the

user in the restraint.

1. Open the harness and move the harness straps to the side of the

restraint.

2. Place the user in the restraint with his/her back positioned against

the back rest in as upright a position as possible.

3. Verify that the harness straps are located in the slots above, but

closest to the top of the user’s shoulders.

4. If the harness straps are not in the appropriate position, move them

according to the instructions provided in Adjusting the Harness

Height.

5. Place the harness shoulder straps over each of the user’s

shoulders making sure that the straps are not twisted or binding on

any object.

6. Fasten the metal latch on each shoulder strap securely into the

buckle.

7. Fasten the plastic chest clip and position it in the middle of the

users chest — aligned with the armpits of the user.

8. Check to ensure the harness fit is snug. If needed, adjust the

harness fit as noted in Adjusting the Harness Fit.

9. To remove the user from the restraint system, reverse steps

outlined above.

Securing the User in the Restraint

 The harness assembly is for use only with the Therapedic

Positioning Restraint System. Do not use the harness

independently of the seat.

 If your Positioning Restraint System becomes badly worn or

damaged, or is involved in an accident, regardless of speed and

regardless how minor, your restraint system may no longer be

effective and should immediately be replaced.

 Secure this Positioning Restraint System even when it is not

occupied; in a crash, an unsecured restraint may injure vehicle

occupants.

 The metal parts on a restraint system can heat up if the vehicle is

parked in the sun. To avoid injury to the occupant, always check

that the metal parts are not too hot before putting the occupant in

the seat. We recommend if you park in the sun, covering your seat

with a blanket or towel to help keep the metal parts from heating up.

 Never leave children unattended in the vehicle, even if they are

secured in a restraint system. Children could be seriously or fatally

injured from excessive exposure to extreme heat or cold.

 Do not leave loose objects in the passenger compartment of your

vehicle. In the event of an accident, these objects can become

projectiles and cause serious injury or death.

IMPORTANT SAFETY INFORMATION:

MODEL #2000: This restraint system conforms to all applicable Federal

motor vehicle safety standards. This restraint is certified for use in

motor vehicles and aircraft.

MODEL #2500: This restraint system conforms to all applicable Federal

motor vehicle safety standards. This restraint is certified for use in

motor vehicles. It is not certified for use in aircraft.

IMPORTANT: Vehicle seats and safety seat belts differ from vehicle to

vehicle. Always refer to your vehicle owner’s manual or call the vehicle

manufacturer for specific information about the use of child restraint

systems in your vehicle. Some vehicles may have seating positions or

seat belts which are not compatible with this Positioning Restraint

System, or any other restraint system.

VEHICLE SEAT BELTS THAT CAN BE USED:

 Continuous-loop lap-shoulder belts with a sliding latch plate.

This type of seat belt consists of continuous webbing that is bolted

to the vehicle on one end and has a retractor on the other end. The

latch plate (the “male” part of the seat belt buckle) slides freely

along the webbing to form a lap belt and a shoulder belt when

attached to the buckle.

 Combination lap-shoulder belts with a locking latch plate. This

type of seat belt has a latch plate (the “male” part of the seat belt

buckle) that locks into place for securing the restraint system.

 Lap belts with automatic locking retractors. These lap belts

automatically lock to whatever length they have been pulled to,

after which they can only be reset by retracting the belt completely.

 Lap belts with a locking latch plate. This type of seat belt stays

locked after the seat belt is tightened by pulling the free end.

VEHICLE SEAT BELTS THAT CANNOT BE USED:

 Seat belts with the top and/or bottom anchor attached to the vehicle

door.

Vehicle Seat Belt Compatibility

Viscoelastic Foam Padding

Set of seat and back foam supports with

an added layer of memory foam to cradle

the body prominences for pressure

reduction and comfort.

Shurshape™ Custom Inserts

A unique way to provide custom molded seating.

The inserts are molded and retain a custom fit

shape.

BuckleGuard

Prevents a child from releasing the shoulder

harness.

Therapedic™ Explorer Mobility Base

Lightweight, folding frames. Ideal alternatives to traditional positioning

wheelchairs. Perfect for use while shopping at the mall, going to the

playground or traveling.

4. To adjust pads, lift the upholstery cover from the sides of the

restraint shell. The pads are located between the inside of the

plastic shell and the cover.

5. Stretch the upholstery cover back over the pads and the edge of

the shell.

Optional Accessories

Seat Depth Extender

The seat depth extender provides extra

support for taller individuals. It is used

when a user’s legs have grown too long to

allow a comfortable seating position.

Extensor Thrust Wedge

Changes seat to back angle by increasing

the front height.

Swing-Away Abductor

The swing-away abductor is

used to improve hip

alignment and stabilize

seating posture.

Headwings

Height adjustable soft-padded headwings

Block Style Positioning Pads

Additional pads for special positioning needs.

Block style, two pads 2½” thick and two pads

1½” thick.

 Lap belts with an emergency locking retractor (ELR), which means

that the lap belt will only lock in the event of a sudden stop or crash.

 Motorized seat belts that automatically surround the passenger

when the door is closed.

 Combination lap and shoulder belts with a “sewn lock plate”. The

lap belt is sewn to the side of the lock plate (the “male” part of the

seat belt buckle), while the shoulder belt is sewn to the top of the

lock plate. Each belt feeds into a separate emergency-locking

retractor prohibiting proper control of the seat belt tension.

 This Positioning Restraint System must ONLY be used in forward-

facing vehicle seats.

 This Positioning Restraint System is to be used ONLY in the

forward-facing position.

 This Positioning Restraint System CANNOT be used in the

following seating positions:

 Rear-facing vehicle seats, such as those in some vans or

buses.

 Side-facing vehicle seats, such as those in some vans and

pick-up trucks.

 Flip-down vehicle seats, often referred to as “jump-seats.”

NOTE: According to research sponsored by the National

Highway Traffic Safety Administration, children are

significantly safer when properly restrained in the back seat,

compared to the front seat.

Vehicle Seating Positions

1. Adjustable Head Pads

2. Shoulder Harness Pads

3. Lateral Positioning Pads (under cover)

4. Crotch Strap Pad

5. Chest Clip

6. Buckle

7. Harness Straps and Clip

8. Metal Side Tubes

9. Buckle Adjustment Strap

10. Tether Strap

11. Instructional Video

12. Locking Clip for Seat Belt

Therapedic™ Features

4. The shoulder straps can be independently adjusted by pressing the

grey button on the tension adjuster then adding or removing slack

in the webbing as necessary to obtain a snug fit.

5. A snug strap should not allow any slack. It lies in a relatively

straight line without sagging. It does not press on the user’s flesh

or push the user’s body into an unnatural position.

Adjusting the Chest Clip

Important: The correct height for the chest clip is at the middle of the

chest — level with the armpit.

1. The chest clip keeps the shoulder straps of the harness from sliding

down off the shoulders.

2. The chest clip if fastened by fitting the two halves together. The

chest clip is properly secured when a click is heard.

3. The chest clip is opened by squeezing the middle tab and pulling

the two pieces apart.

4. With the harness properly attached and the chest clip fastened, the

chest clip should be positioned at the middle of the chest, in line

with the armpits of the user.

Adjusting the Head Pads

1. The Positioning Restraint System has adjustable head pads.

2. Determine if the head pad(s) need to be adjusted.

3. Locate the plastic ball on the lanyard that is located behind and to

the side of each head pad.

4. Press the button on the plastic ball, sliding the head pad along the

lanyard to the desired height, then release the button to secure the

head pad into position.

Adjusting Lateral Positioning Pads

1. The Positioning Restraint System comes standard with four flat

positioning pads which are designed to be adjusted to offer the user

more or less support as needed. The pads are located under the

cover on the sides of the restraint.

2. The lateral positioning pads can be used to decrease the inside

width of the car seat if the seat is too wide.

3. Use only as many pads as needed for a correct fit. As a guideline,

you should have about one inch of space on either side of the user

and the restraint seat cover.

Checking the Harness Height

1. Place the user in the Positioning Restraint System and properly

secure with the harness.

2. Note the position of the harness relative to the shoulder of the user.

 Harness straps should be inserted in the nearest slot at or above

the user’s shoulder.

 If the harness height is correct, the restraint can be used with no

further adjustment.

 If the height of the user’s shoulder is above the harness it will be

necessary to adjust the harness. See Adjusting the Harness

Height.

Adjusting the Harness Height

1. To adjust the harness, it is necessary to

remove the Positioning Restraint System

from the vehicle.

2. Place the user in the restraint and identify

the closest harness slot at or above the

height of the user’s shoulder.

3. Remove the user from the restraint prior to

making any adjustments to the harness.

4. Locate the metal bracket securing the top of the harness along the

back side of the restraint and pull it away to expose 3"- 4" (76.2 —

101.6 mm) of webbing.

5. Turn the metal bracket so the short side will fit through the slot in

the back of the restraint and push it through the slot as well as the

cover.

6. Reposition the harness to the correct slot and reverse the process

to reinstall the harness.

7. After repositioning the harness, make sure the metal bracket is flat

against the back of the restraint to prevent it from slipping out.

Adjusting the Harness Fit

1. With the user in the restraint, check the location of the buckle.

2. The buckle should be positioned at the level of the user’s hips, not

over the stomach area.

3. If necessary, the position of the buckle can be changed by adjusting

the metal bracket on the bottom of the restraint.

10 12

Installation

The Therapedic Positioning Restraint System must be installed

with a Tether Strap which is included. The tether strap must be

attached properly to a LATCH top tether anchor or must be bolted

into a structurally secure location in the vehicle. See “Installing

the Tether Strap.”

Use of the tether improves the safety of the Positioning Restraint

System and reduces the risk of injury.

Vehicle Lap and Shoulder Belt (Recommended Method)

This is the recommended method for installing the Therapedic

Positioning Restraint System and is used in vehicles equipped with an

Automatic Locking Retractor (ALR) function. The ALR allows the

user to lock the retractor at a set position (also called child restraint

mode) used for securing child seats. ALR mode is activated by

extending the retractor all the way out until a "click" is heard, next let

the seat belt (webbing) retract into the retractor to the desired length

and stop the belt at that point. The retractor locks and will not let the

belt lengthen at that point (only retract).

1. Place the Positioning Restraint System in a forward facing position

on the vehicle seat. If the front edge of the restraint extends

more that 1” (25mm) beyond the front edge of the seat, then

the vehicle seat is too shallow to properly support the restraint

system. If this is the case, do not install.

2. Attach the tension adjuster hooks of the tether to the upper anchor

points located on the sides of the Positioning Restraint System. See

Installing the Tether Strap.

3. Attach the tether loosely to an approved anchor

point in the vehicle. In cars built after 2002,

approved anchor points can be identified by this

symbol. Refer to your vehicle owner’s manual if

needed.

4. Verify that the seat belt in the vehicle can be

used with the Positioning Restraint System. See Vehicle Seat Belt

Compatibility.

The Therapedic Positioning

Restraint System includes the

following standard components:

 5-Point Safety Harness

 Shoulder Harness Pads

 Adjustable Head Pads

 Crotch Strap Pad

 Lateral Positioning Pads

 Tether Strap Kit

 Locking Clip

Operating the Harness Buckle

 To release, press the red button on the harness buckle.

 To close, insert one metal latch into the harness buckle until it clicks.

Repeat for the other metal latch.

 Always make sure both latches are properly fastened in the harness

buckle when securing a user.

 Never lubricate the harness buckle.

Components and Adjustments

 For individuals greater than 80 lbs. (36 kg): use two (2)

tether hooks attaching one (1) tether hook to the tether

anchor immediately behind the restraint AND one (1) tether

hook to the closest adjacent tether anchor. See Figure 8.

5. Remove any slack in the tether by pulling the loose ends of the

tether through the tension adjuster hooks.

6. Verify that the tether is appropriately attached and tensioned as

noted above.

Non-LATCH Vehicle Installation: If the desired seating position in the

vehicle does not have a LATCH top tether anchor (which may be the

case for vehicles that were made before 2002), it is necessary to use a

bolt-in anchor mounting bracket to secure the tether strap. Contact

Columbia Medical directly for more details on acquiring an anchor

mounting bracket.

Figure 8: Double hook

attachment for

individuals over 80 lbs.

(36kg)

Figure 9: Tether

Anchoring Methods

5. Pull the seat belt out completely to engage

the retractor, then route the belt between the

back of the restraint and the metal tubes

which are located along the sides of the

Positioning Restraint System.

6. Make sure that the seat belt is not twisted,

then buckle in place.

7. Make sure the restraint system is flat against the vehicle seat’s

bottom and back. Use your hands to apply firm pressure to the

restraint, pushing it into the vehicle backrest—or place your knee on

the restraint and push down with all your weight—-while pulling on the

vehicle seat belt and removing all slack from it.

8. Check to make sure the tether strap is not twisted and then tighten to

secure the upper portion of the restraint. If the vehicle does not have

a top tether anchor point, it will be necessary to use a bolt-in anchor

mounting bracket. See Non-LATCH Vehicle Installation.

9. DO NOT USE this restraint without the tether strap properly installed.

10. Verify that the vehicle seat belt is tight and that the Positioning

Restraint System is secure. When properly installed, the restraint will

not move more that 1” (25mm) from side to side and or front to back.

If the restraint is not secure, repeat steps 5 – 8.

Vehicle Lap and Shoulder Belt – Requires Locking Clip

This method of installation is required when installing the Therapedic

Positioning Restraint System in a vehicle with an emergency locking

retractor (ELR) type of seat belt. Emergency Locking Retractor (ELR)

function allows the occupant to have free movement while buckled up, but

in the event of an emergency situation, such as heavy braking or collision,

the retractor instantly locks securing the occupant. This type of seat belt

is "webbing sensitive," meaning that any sudden movement of the

webbing (the seat belt strap) causes the retractor to instantly lock. A

locking clip is required to achieve the proper tension when using

this belt type to secure a restraint.

1. Place the Positioning Restraint System in a forward facing position on

the vehicle seat. If the front edge of the restraint extends more

that 1” (25mm) beyond the front edge of the seat, then the vehicle

seat is too shallow to properly support the restraint system. If

this is the case, do not install.

2. Attach the tension adjuster hooks of the tether to the upper anchor

points located on the sides of the Positioning Restraint System. See

Installing the Tether Strap.

3. Attach the tether loosely to an approved anchor

point in the vehicle. In cars built after 2002,

approved anchor points can be identified by this

symbol. Refer to your vehicle owner’s manual if

needed.

4. Verify that the seat belt in the vehicle can be used

with the Positioning Restraint System. See Vehicle Seat Belt

Compatibility.

5. Pull the seat belt out completely then route the belt between the back

of the restraint and the metal tubes which are located along the sides

of the Positioning Restraint System.

6. Make sure that the seat belt is not twisted, then buckle in place.

7. Make sure the restraint system is flat against the vehicle seat’s bottom

and back. Use your hands to apply firm pressure to the restraint,

pushing it into the vehicle backrest—or place your knee on the

restraint and push down with all your weight—-while pulling on the

vehicle seat belt and removing all slack from it.

8. With one hand, firmly hold the shoulder and lap portions of the seat

belt together immediately behind the latch, then release the seat belt

latch from the buckle.

9. Fold the webbing and thread it through the locking clip, one side at a

time keeping the locking clip as close as possible to vehicle belt latch –

no further than ½" (12mm) away. See Figure 3.

10. Buckle the seat belt to see that the clip has been correctly installed,

with all slack webbing gone and the restraint tightly in place.

11. Check to make sure the tether strap is not twisted and then tighten to

secure the upper portion of the restraint. If the vehicle does not have a

top tether anchor point, it will be necessary to use a bolt-in anchor

mounting bracket. See Installation Without LATCH Top Tether

Anchors.

12. DO NOT USE this restraint without the tether strap properly installed.

13. Verify that the vehicle seat belt is tight and that the Positioning

Figure 7: Single hook

attachment for individuals

under 80 lbs. (36kg)

3. Attach one tension adjuster hook to the upper side anchor bracket

located on each side of the restraint.

See Figure 6.

4. Attach the tether hook(s) to the vehicle’s tether anchor(s). The

primary tether anchor to use will be located immediately behind the

restraint.

 For individuals less than 80 lbs. (36 kg): attach one (1)

tether hook to the tether anchor immediately behind the

restraint. See Figure 7.

Figure 6: Attaching tether to upper

side anchor bracket

 An incorrectly mounted restraint system may come loose during an

accident which could result in serious injury or death to the user.

 Damaged or impact damaged restraint systems should be replaced

immediately.

 For occupants over 80 lbs. (36 kg), BOTH tether hooks must be

used. Each hook must be attached to a separate tether

anchor. A single tether anchor is not strong enough to

support weights in excess of 80 lbs. (36 kg).

Installing the Tether with LATCH

1. The tether is not attached during shipping. Locate the tether and

remove it from its plastic bag.

2. The tether has two (2) tension adjuster hooks (one located on

each end of the tether) and two (2) “free-floating” tether hooks.

See Figure 5.

Free-floating tether hooks to attach

to vehicle’s LATCH upper anchor

points

Figure 5: Illustration of tether

Tension adjuster hooks

Figure 3: Combination Lap/

Shoulder Belt with Locking Clip

Restraint System is secure. When properly installed, the restraint

will not move more that one inch (1”) from side to side and or front

to back. If the restraint is not secure, repeat steps 5 – 11.

Vehicle Lap Belt Only

1. Place the Positioning Restraint System

in a forward facing position on the

vehicle seat. If the front edge of the

restraint extends more that

1” (25mm) beyond the front edge of

the seat, then the vehicle seat is too

shallow to properly support the

restraint system. If this is the case,

do not install.

2. Attach the tension adjuster hooks of

the tether to the upper anchor points located

on the sides of the Positioning Restraint

System. See Installing the Tether Strap.

3. Attach the tether loosely to an approved anchor point in the vehicle.

In cars built after 2002, approved points can be identified by this

symbol. Refer to your vehicle anchor owner’s manual if needed.

4. Check the seat belt in the vehicle to verify that it can be used with

the Positioning Restraint System. See Vehicle Seat Belt

Compatibility. This restraint cannot be used with lap belts with an

emergency locking retractor (ELR), which means that the lap belt

will only lock in the event of a sudden stop or crash.

5. Pull the lap belt out completely, then route the belt

between the back of the restraint and the metal tubes

which are located along the sides of the Positioning

Restraint System.

Figure 4: Lap Belt Only

6. Make sure that the seat belt in not twisted, then buckle in place.

7. Make sure the restraint system is flat against the vehicle seat’s

bottom and back. Use your hands to apply firm pressure to the

restraint, pushing it into the vehicle backrest—or better yet, place

your knee on the restraint and push down with all your weight—-

while pulling on the vehicle seat belt and removing all slack from it.

8. Check to make sure the tether strap is not twisted and then tighten

to secure the upper portion of the restraint. If the vehicle does not

have a top tether anchor point, it will be necessary to use a bolt-in

anchor mounting bracket. See Installation Without LATCH Top

Tether Anchors.

9. DO NOT USE this restraint without the tether strap properly

installed.

10. Verify that the vehicle seat belt is tight and that the Positioning

Restraint System is secure. When properly installed, the restraint

will not move more that 1” (25mm) from side to side and or front to

back. If the restraint is not secure, repeat steps 4 — 7.

Aircraft Installation

1. Place the Positioning Restraint System in a forward facing position

on the vehicle seat. If the front edge of the restraint extends

more that 1” (25mm) beyond the front edge of the seat, then

the vehicle seat is too shallow to properly support the restraint

system. If this is the case, do not install.

2. Pull the lap belt out completely, then route the belt between the

back of the restraint and the metal tubes which are located along

the sides of the Positioning Restraint System.

3. Make sure that the seat belt in not twisted, then buckle in place.

4. Make sure the restraint system is flat against the vehicle seat’s

bottom and back. Use your hands to apply firm pressure to the

restraint, pushing it into the vehicle backrest—or better yet, place

your knee on the restraint and push down with all your weight—-

while pulling on the vehicle seat belt and removing all slack from it.

5. Verify that the vehicle seat belt is tight and that the Positioning

Restraint System is secure. When properly installed, the restraint

will not move more that 1” (25mm) from side to side and or front to

back.

Installing the Tether Strap

LATCH Vehicle Installation

The TheraPedic Positioning Restraint System includes a top anchorage

strap, known as a tether. The tether is engineered to make attachment

to the upper anchor points of the LATCH system easier.

LATCH (Lower Anchor and Tethers for CHildren) anchors have been

required on all US passenger vehicles since 2002.

IMPORTANT: Read these instructions completely and check your

vehicle owner’s manual prior to installation to determine the proper

attachment method and locations to position this Positioning Restraint

System.

IMPORTANT SAFETY WARNINGS:

The tether must be used when installing the Positioning Restraint

System. Use of the tether improves safety and reduces the risk of

injury.

 The tether must only be attached to tether anchor points designated

as tether anchor points by the vehicle

manufacturer. This icon is used by vehicle

manufacturers to identify the LATCH

anchors. Use of other locations is not

approved or permitted.

Without tether strap

with

Columbia THERAPEDIC 2500 Instructions For Use Manual

Brand: Columbia

Model: THERAPEDIC 2500

Category: Car seat

Type: Instructions For Use Manual

This manual is also suitable for

THERAPEDIC 2000

Download PDF

report

Columbia THERAPEDIC 2500 Instructions For Use Manual

This manual is also suitable for

Columbia THERAPEDIC 2500 Instructions For Use Manual

Related papers

Other documents