Samsung LN32B360C5D User manual

LCD TV

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please

register your product at

www.samsung.com/register

Model Serial No.

BN68-01975A-01

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Comuníquese con SAMSUNG WORLDWIDE

Si desea formular alguna pregunta o comentario en relación con los productos de Samsung, comuníquese con el centro de

atención al cliente de SAMSUNG.

Country

Customer Care Center

Web Site Address

CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca

Samsung Electronics Canada Inc., Customer

Service 55 Standish Court Mississauga,

Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc., Service

à la Clientèle 55 Standish Court Mississauga,

Ontario L5R 4B2 Canada

U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com/us

Samsung Electronics America, Inc.

105 Challenger Road

Ridgefield Park, NJ 07660-0511

BN68-01975A-00L02.indb 1 2009-01-23 �� 5:07:48

Important Warranty Information Regarding Television Format Viewing

See the warranty card for more information on warranty terms.

Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen

format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to

ll the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images

on screen, such as the dark sidebars on nonexpanded standard format television video and programming, should be limited to no

more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites

or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that

exceed the above guidelines can cause uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in

the LCD picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary

patterns or dark bars.

On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format selection

and use, as well as burned-in images, are not covered by your Samsung limited warranty.

SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung

Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG

will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and

in Canada on SAMSUNG products purchased in the United States, for the warranty period originally specied, and to the

Original Purchaser only.

The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this

Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the

Service Center. Transportation to and from the Service Center is the responsibility of the purchaser.

Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in

normal use of the product.

Excluded, but not limited to, are any originally specied provisions for, in-home or on-site services, minimum or maximum

repair times, exchanges or replacements, accessories, options, upgrades, or consumables.

For the location of a SAMSUNG Authorized Service Center, please call toll-free:

In the United States : 1-800-SAMSUNG (1-800-726-7864)

In Canada : 1-800-SAMSUNG

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image

retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the

screen when displaying a still image.

Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,

right and center of the screen caused by the difference of light emission on the screen.

Playing a DVD or a game console may cause a similar effect to the screen.

Damages caused by the above effect are not covered by the Warranty.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

❑

N

●

N

❑

●

BN68-01975A-00L02.indb 1 2009-01-23 �� 5:07:48

English - 1

CONTENTS

License

TruSurround HD, SRS and Symbol are trademarks of SRS Labs, Inc.

TruSurround HD technology is incorporated under license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks

of Dolby Laboratories.

Symbol

N O T

Note One-Touch Button TOOL Button

❑

General Information

List of Features .....................................................................2

Accessories

..........................................................................2

Viewing the Control Panel

....................................................3

Viewing the Connection Panel

..............................................4

Remote Control

....................................................................6

Installing Batteries in the Remote Control

............................6

Connections (LN19B360, LN22B360)

Connecting VHF and UHF Antennas ....................................7

Connecting Cable TV

...........................................................7

Connecting a DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box) via HDMI

............................8

Connecting a DVD / Blu-ray player / Cable Box / Satellite

receiver (Set-Top Box) via DVI

.............................................9

Connecting a DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box) via Component cables

.......9

Connecting a VCR

..............................................................10

Connecting a Digital Audio System

....................................10

Connecting an Amplier / DVD Home Theater

...................11

Connecting a Camcorder....................................................12

Connecting a PC

................................................................13

Connections (LN26B360, LN32B360)

Connecting VHF and UHF Antennas ..................................14

Connecting Cable TV

.........................................................14

Connecting a DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box) via HDMI

..........................15

Connecting a DVD / Blu-ray player / Cable Box / Satellite

receiver (Set-Top Box) via DVI

...........................................16

Connecting a DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box) via Component cables

.....16

Connecting a VCR

..............................................................17

Connecting a Digital Audio System

....................................17

Connecting an Amplier / DVD Home Theater

...................18

Connecting a Camcorder....................................................19

Connecting a PC

................................................................20

■

Operation

Viewing the menus .............................................................21

Plug & Play Feature............................................................22

Channel Control

Conguring the Channel Menu ...........................................23

Managing Channels ...........................................................23

Picture Control

Conguring the Picture Menu .............................................25

Using Your TV as a Computer (PC) Display

.......................27

Setting up the TV with your PC

..........................................28

Sound Control

Conguring the Sound Menu ..............................................29

Setup

Conguring the Setup Menu ...............................................30

Input / Support

Conguring the Input Menu ................................................34

Conguring the Support Menu............................................34

Appendix

Troubleshooting ..................................................................36

Installing the Stand

.............................................................37

Disconnecting the Stand.....................................................37

How to Adjust the Stand (LN19B360)

.................................38

How to Adjust the Angle of the TV (LN19B360)

..................38

Installing VESA Compliant Mounting Devices (LN19B360)

39

Using the Decoration Covers (LN19B360)

.........................39

Wall Mount Kit Specications (VESA)

................................40

Using the Anti-Theft Kensington Lock

................................40

Securing the TV to the Wall

................................................41

Specications

.....................................................................42

Dimensions

.........................................................................43

■

English

BN68-01975A-00L02.indb 1 2009-01-23 �� 5:07:49

English - 2

GENERAL INFORMATION

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

Product design and specications may be changed without notice in order to enhance product performance.

List of Features

Adjustable picture settings that can be stored in the TV’s memory.

Automatic timer to turn the TV on and off.

A special sleep timer.

Excellent Digital Interface & Networking :

With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver (Set-Top

Box) needed.

HDMI/DVI connection of your PC to this TV.

Excellent Picture Quality

SRS TruSurround HD provides a virtual surround system.

Accessories

Remote Control

(BN59-00857A) &

Batteries (AAA x 2)

Power Cord

(3903-000144)

TV-Holder & Screw (M4 X L16)

(LN32B360: BN96-10788A)

Cleaning Cloth

(BN63-01798B)

Cover-Bottom

(LN22B360: BN63-04269A)

(LN26B360: BN63-04269A)

(LN32B360: BN63-05326A)

Screw (M4 X L16)

(LN22B360: 6002-001294)

(LN26B360: 6002-001294)

(LN32B360: 6002-001294)

Screw (M4 X L14)

(LN32B530: 6003-001334)

Wall Mount kit

(LN19B360: BN96-04960A)

Decoration Cover

(LN19B360: Right- BN63-04242A

Left- BN63-04254A)

Owner’s Instructions Warranty Card /

Safety Guide Manual

Please make sure the following items are included with your LCD TV. If any items

are missing, contact your dealer.

The items color and shape may vary depending on the model.

N

¦

●

¦

N

BN68-01975A-01Eng.indd 2 2009-01-30 �� 9:14:10

English - 3

Viewing the Control Panel

The product color and shape may vary depending on the model.

You can use a button by pressing the side panel buttons.

1

SOURCE

E

: Toggles between all the available input sources. In the on-screen menu, use this button as you use the

ENTER

E

button on the remote control.

2

MENU: Press to see an on-screen menu of your TV’s features.

3

y

: Press to increase or decrease the volume. In the on-screen menu, use the

y

buttons as you would use the

◄ and ► buttons on the remote control.

4

Z

: Press to change channels. In the on-screen menu, use the

Z

buttons as you would use the ▼ and ▲ buttons

on the remote control.

5

P

(POWER): Press to turn the TV on and off.

6

SPEAKERS

7

REMOTE CONTROL SENSOR: Aim the remote control towards this spot on the TV.

8

POWER INDICATOR: Blinks and turns off when the power is on and lights up in stand-by mode.

¦

N

BN68-01975A-00L02.indb 3 2009-01-23 �� 5:07:50

English - 4

Viewing the Connection Panel

The product color and shape may vary depending on the model.

¦

N

LN19B360, LN22B360



LN26B360, LN32B360



[TV Rear Panel]

8 6 3 # 2

7

0

9

1!@

0

9

!@#

21 3 4 5 7 8

8 6 3 # 2

7

0

9

1!@

0

9

!@#

21 3 4 5 7 8

[TV Rear Panel]

BN68-01975A-00L02.indb 4 2009-01-23 �� 5:07:50

English - 5

1

EX-LINK

Connector for service only.

2

DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component such as a Home theater receiver.

3

PC IN [PC] / [AUDIO]

Connects to the video and audio output jacks on your PC.

4

H

(HEADPHONE)

Connects a set of external headphones for private listening.

5

HDMI (DVI) IN / DVI AUDIO IN [R-AUDIO-L] (LN19B360, LN22B360)

Connects to the HDMI jack of a device with an HDMI output.

No sound connection is needed for an HDMI to HDMI connection.

Use the HDMI (DVI) IN jack for DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI adapter

(DVI to HDMI) for video connection and the DVI AUDIO IN [R-AUDIO-L] jacks for audio.

When using an HDMI/DVI cable connection, you must use the HDMI (DVI) IN jack.

You can also use the ports to connect to a PC.

6

HDMI IN 1, 2 / DVI IN(HDMI1)[R-AUDIO-L] (LN26B360, LN32B360)

Connects to the HDMI jack of a device with an HDMI output.

No sound connection is needed for an HDMI to HDMI connection.

Use the HDMI IN 1 jack for DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI adapter

(DVI to HDMI) for video connection and the DVI IN (HDMI1) [R-AUDIO-L] jacks for audio.

When using an HDMI/DVI cable connection, you must use the HDMI IN 1 jack.

You can also use the ports to connect to a PC.

7

SERVICE

Connector for software upgrades.

8

ANT IN

Connects to an antenna or cable TV system.

9

POWER INPUT

Connects the supplied power cord.

0

KENSINGTON LOCK

The Kensington Lock (optional) is a device used to physically x the system when used in a public place. If you want to

use a locking device, contact the dealer where you purchased the TV.

The location of the Kensington Lock may be different depending on its model.

!

AV IN

Video and audio inputs for external devices, such as a camcorder or VCR.

@

COMPONENT IN

Connects Component video / audio.

#

AUDIO OUT

Connects to the audio input jacks on your Amplier/Home theater.

–

N

–

N

–

N

–

BN68-01975A-00L02.indb 5 2009-01-23 �� 5:07:50

English - 6

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

The performance of the remote control may be affected by bright light.

The product color and shape may vary depending on the model.

N

1

POWER: Turns the TV on and

off.

2

NUMERIC BUTTONS: Press to

change the channel.

3

_: Press to select additional

channels (digital) being

broadcast by the same station.

For example, to select channel

‘54-3’, press ‘54’, then press _

and ‘3’.

4

MUTE

M

: Press to temporarily

cut off the sound.

5

y

: Press to increase or

decrease the volume.

6

CH LIST: Used to display

Channel Lists on the screen.

7

TOOLS: Use to quickly select

frequently used functions.

8

INFO: Press to display

information on the TV screen.

9

COLOR BUTTONS: Use these

buttons in the Channel list menus

etc.

0

P.SIZE: Picture size selection.

!

TV: Selects the TV mode directly.

@

PRE-CH: Enables you to return

to the previous channel you were

watching.

#

z

: Press to change

channels.

$

SOURCE: Press to display

and select the available video

sources.

%

FAV.CH: Press to switch to your

favorite channels.

^

MENU: Displays the main on-

screen menu.

&

RETURN: Returns to the

previous menu.

*

 UP▲/DOWN▼/LEFT◄/

RIGHT►/ENTER

E

: Use to

select on-screen menu items and

change menu values.

(

EXIT: Press to exit the menu.

)

CC: Controls the caption

decoder.

a

MTS: Press to choose stereo,

mono or Separate Audio

Program (SAP broadcast).

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside the

compartment.

3. Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the

remote control for a long time. (Assuming typical TV usage, the batteries should last for about one year.)

If the remote control doesn’t work, check the following:

Is the TV power on?

Are the plus and minus ends of the batteries reversed?

Are the batteries drained?

Is there a power outage or is the power cord unplugged?

Is there a special uorescent light or neon sign nearby?

¦

N

●

1

!

@

#

$

%

^

&

*

(

)

a

2

3

4

5

6

7

8

9

0

BN68-01975A-00L02.indb 6 2009-01-23 �� 5:07:51

English - 7

CONNECTIONS (LN19B360, LN22B360)

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see ‘Antennas with 300

Ω Flat Twin Leads’ below.

If your antenna has one lead that looks like the diagram to the right, see ‘Antennas with 75 Ω

Round Leads’.

If you have two antennas, see ‘Separate VHF and UHF Antennas’.

Antennaswith300ΩFlatTwinLeads

If you are using an off-air antenna (such as a roof antenna or ‘rabbit ears’) that has 300Ω twin

at leads, follow the directions below.

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not

supplied). Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

Plug the antenna lead into the ANT IN terminal on the back of the TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine

the two antenna signals before connecting the antennas to the TV. This procedure requires an

optional combiner-adaptor (available at most electronics shops).

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable

channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled ‘ANT OUT’, ‘VHF OUT’ or simply, ‘OUT’.

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

¦

N

ANT IN

UHF

VHF

ANT IN

UHF

VHF

ANT IN

ANT IN ANT OUT

ANT IN

BN68-01975A-00L02.indb 7 2009-01-23 �� 5:07:51

English - 8

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-

way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)

1. Find and disconnect the cable that is connected to the ANT IN terminal on your cable box.

This terminal might be labeled ‘ANT IN’, ‘VHF IN’ or simply, ‘IN’.

2. Connect this cable to a two-way splitter.

3. Connect an RF cable between the OUTPUT terminal on the splitter and the IN terminal on the cable box.

4. Connect an RF cable between the ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

5. Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

6. Connect the last RF cable between the OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the TV.

After you have made this connection, set the A/B switch to the ‘A’ position for normal viewing. Set the A/B switch to the ‘B’

position to view scrambled channels. (When you set the A/B switch to ‘B’, you will need to tune your TV to the cable box’s

output channel, which is usually channel 3 or 4.)

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

1. Connect an HDMI Cable between the HDMI (DVI) IN jack on the TV and the HDMI jack on the DVD / Blu-ray Player or Cable

Box / Satellite receiver (Set-Top Box).

What is HDMI?

HDMI(High-Denition Multimedia Interface), is an interface that enables the transmission of digital audio and video signals

using a single cable.

The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital

Copy Protection) coding feature installed.

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

ferent back panel conguration.

The TV may not output sound and pictures may be displayed with abnormal color when DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box) supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI

cable and there is no sound, connect the HDMI cable to the HDMI (DVI) IN jack and the audio cables to the DVI AUDIO

IN [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that provided the DVD / Blu-ray player /

Cable Box / Satellite receiver (Set-Top Box) to conrm the HDMI version, then request an upgrade.

HDMI cables that are not 1.3 may cause annoying icker or no screen display.

N

¦

N

●

N

Splitter

Cable Box

Incoming cable

TV Rear

ANT IN

RF (A/B) Switch

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

TV Rear Panel

1

HDMI Cable (Not supplied)

BN68-01975A-00L02.indb 8 2009-01-23 �� 5:07:52

English - 9

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.

1. Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI (DVI) IN jack on the TV and the DVI jack on the DVD /

Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the DVI AUDIO IN [R-AUDIO-L] jack on the TV and the DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box).

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

ferent back panel conguration.

When connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box), match the color of the connection

terminal to the cable.

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) to

your TV.

1. Connect a Component Cable between the COMPONENT IN [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR]

jacks on the DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the COMPONENT IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD /

Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality.

Be sure to match the component video and audio connections. For example, if connecting a Component video cable to

COMPONENT IN, connect the audio cable to COMPONENT IN also.

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

ferent back panel conguration.

When connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box), match the color of the connection

terminal to the cable.

¦

N

¦

N

TV Rear Panel

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

2

Audio Cable (Not supplied)

1

Component Cable (Not supplied)

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

TV Rear Panel

2

Audio Cable (Not supplied)

1

DVI to HDMI Cable (Not supplied)

BN68-01975A-00L02.indb 9 2009-01-23 �� 5:07:52

English - 10

Connecting a VCR

1. Connect a Video Cable between the AV IN [VIDEO] jack on the TV and the VIDEO OUT jack on the VCR.

2. Connect Audio Cables between the AV IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the VCR.

If you have a ‘mono’ (non-stereo) VCR, use a Y-connector (not supplied) to connect to the right and left audio input jacks

of the TV. Alternatively, connect the cable to the ‘R’ jack. If your VCR is stereo, you must connect two cables.

Each VCR has a different back panel conguration.

When connecting a VCR, match the color of the connection terminal to the cable.

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System (Home theater/Receiver) to your TV.

1. Connect an Optical Cable between the DIGITAL AUDIO OUT (OPTICAL) jacks on the TV and the Digital Audio Input jacks on

the Digital Audio System.

When a Digital Audio System is connected to the DIGITAL AUDIO OUT (OPTICAL) jack: Decrease the volume of the TV

and adjust the volume level with the system’s volume control.

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

Each Digital Audio System has a different back panel conguration.

When the Home Theater receiver is set to On, you can hear sound output from the TV’s Optical jack. When the TV is

displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a

digital component such as a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) and is connected to the

TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver. If you want to hear 5.1 channel audio,

connect the digital audio out jack on DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) directly to an

Amplier or Home Theater, not the TV.

¦

N

¦

N

2

Audio Cable (Not supplied)

VCR Rear Panel

1

Video Cable (Not supplied)

TV Rear Panel

Digital Audio System

1

Optical Cable (Not supplied)

TV Rear Panel

BN68-01975A-00L02.indb 10 2009-01-23 �� 5:07:53

English - 11

ConnectinganAmplier/DVDHomeTheater

1. Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] jacks on the TV and Audio Input jacks on the Amplier / DVD

Home Theater.

When an audio amplier is connected to the AUDIO OUT [R-AUDIO-L] jacks: Decrease the volume of the TV and adjust

the volume level with the Amplier’s volume control.

Each Amplier/DVD Home Theater has a different back panel conguration.

When connecting an Amplier/DVD Home Theater, match the color of the connection terminal to the cable.

¦

N

TV Rear Panel

1

Audio Cable (Not supplied)

Amplier/DVDHomeTheater

BN68-01975A-00L02.indb 11 2009-01-23 �� 5:07:53

English - 12

Connecting a Camcorder

Using a Video Cable

1. Connect a Video Cable between the AV IN [VIDEO] jack on the TV and the VIDEO OUT jack on the camcorder.

2. Connect Audio Cables between the AV IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the camcorder.

Each Camcorder has a different back panel conguration.

When connecting a Camcorder, match the color of the connection terminal to the cable.

Using an HDMI Cable

1. Connect a HDMI Cable between the HDMI (DVI) IN jack on the TV and the HDMI OUT jack on the camcorder.

¦

N

TV Rear Panel

HD Camcorder

TV Rear Panel

1

Video Cable (Not supplied)

2

Audio Cable (Not supplied)

Camcorder

1

HDMI Cable (Not supplied)

BN68-01975A-00L02.indb 12 2009-01-23 �� 5:07:54

English - 13

Connecting a PC

Using a D-Sub Cable

1. Connect a D-Sub Cable between PC IN [PC] connector on the TV and the PC output connector on your computer.

2. Connect a PC Audio Cable between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your

computer.

When connecting a PC, match the color of the connection terminal to the cable.

Using an HDMI/DVI Cable

1. Connect an HDMI/DVI cable between the HDMI (DVI) IN jack on the TV and the PC output jack on your computer.

2. Connect a 3.5 mm Stereo miniplug / 2RCA Cable between the DVI AUDIO IN [R-AUDIO-L] jack on the TV and the Audio Out

jack of the sound card on your computer.

Using an HDMI Cable

1. Connect an HDMI cable between the HDMI (DVI) IN jack on the TV and the PC output jack on your computer.

Each PC has a different back panel conguration.

¦

N

TV Rear Panel

PC

2

3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)

1

HDMI/DVI Cable (Not supplied)

PC

TV Rear Panel

1

HDMI Cable (Not supplied)

TV Rear Panel

PC

2

PC Audio Cable (Not supplied)

1

D-Sub Cable (Not supplied)

BN68-01975A-00L02.indb 13 2009-01-23 �� 5:07:55

English - 14

CONNECTIONS (LN26B360, LN32B360)

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see ‘Antennas with 300

Ω Flat Twin Leads’ below.

If your antenna has one lead that looks like the diagram to the right, see ‘Antennas with 75 Ω

Round Leads’.

If you have two antennas, see ‘Separate VHF and UHF Antennas’.

Antennaswith300ΩFlatTwinLeads

If you are using an off-air antenna (such as a roof antenna or ‘rabbit ears’) that has 300Ω twin

at leads, follow the directions below.

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not

supplied). Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

Plug the antenna lead into the ANT IN terminal on the back of the TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine

the two antenna signals before connecting the antennas to the TV. This procedure requires an

optional combiner-adaptor (available at most electronics shops).

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable

channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled ‘ANT OUT’, ‘VHF OUT’ or simply, ‘OUT’.

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

¦

N

ANT IN

UHF

VHF

ANT IN

UHF

VHF

ANT IN

ANT IN ANT OUT

ANT IN

BN68-01975A-00L02.indb 14 2009-01-23 �� 5:07:55

English - 15

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-

way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)

1. Find and disconnect the cable that is connected to the ANT IN terminal on your cable box.

This terminal might be labeled ‘ANT IN’, ‘VHF IN’ or simply, ‘IN’.

2. Connect this cable to a two-way splitter.

3. Connect an RF cable between the OUTPUT terminal on the splitter and the IN terminal on the cable box.

4. Connect an RF cable between the ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

5. Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

6. Connect the last RF cable between the OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the TV.

After you have made this connection, set the A/B switch to the ‘A’ position for normal viewing. Set the A/B switch to the ‘B’

position to view scrambled channels. (When you set the A/B switch to ‘B’, you will need to tune your TV to the cable box’s

output channel, which is usually channel 3 or 4.)

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

1. Connect an HDMI Cable between the HDMI IN (1 or 2) jack on the TV and the HDMI jack on the DVD Player or Cable Box /

Satellite receiver (Set-Top Box).

What is HDMI?

HDMI(High-Denition Multimedia Interface), is an interface that enables the transmission of digital audio and video signals

using a single cable.

The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital

Copy Protection) coding feature installed.

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

ferent back panel conguration.

The TV may not output sound and pictures may be displayed with abnormal color when DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box) supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI

cable and there is no sound, connect the HDMI cable to the HDMI IN 1 jack and the audio cables to the DVI IN (HDMI 1)

[R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that provided the DVD / Blu-ray player /

Cable Box / Satellite receiver (Set-Top Box) to conrm the HDMI version, then request an upgrade.

HDMI cables that are not 1.3 may cause annoying icker or no screen display.

N

¦

N

●

N

Splitter

Cable Box

Incoming cable

TV Rear

ANT IN

RF (A/B) Switch

TV Rear Panel

1

HDMI Cable (Not supplied)

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

BN68-01975A-00L02.indb 15 2009-01-23 �� 5:07:55

English - 16

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.

1. Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI IN 1 jack on the TV and the DVI jack on the DVD /

Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the DVI IN (HDMI 1) [R-AUDIO-L] jack on the TV and the DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box).

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

ferent back panel conguration.

When connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box), match the color of the connection

terminal to the cable.

When using an HDMI / DVI cable connection, you must use the HDMI IN 1 jack.

Connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) to

your TV.

1. Connect a Component Cable between the COMPONENT IN [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR]

jacks on the DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the COMPONENT IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD /

Blu-ray player / Cable Box / Satellite receiver (Set-Top Box).

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality.

Be sure to match the component video and audio connections. For example, if connecting a Component video cable to

COMPONENT IN, connect the audio cable to COMPONENT IN also.

Each DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box) has a dif

ferent back panel conguration.

When connecting a DVD / Blu-ray player / Cable Box / Satellite receiver (Set-Top Box), match the color of the connection

terminal to the cable.

¦

N

¦

N

TV Rear Panel

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

2

Audio Cable (Not supplied)

1

Component Cable (Not supplied)

DVD / Blu-ray player / Cable Box /

Satellite receiver (Set-Top Box)

TV Rear Panel

2

Audio Cable (Not supplied)

1

DVI to HDMI Cable (Not supplied)

BN68-01975A-00L02.indb 16 2009-01-23 �� 5:07:56

English - 17