Tektronix P5200A User manual

x

P5200A Series

High Voltage Differential Probes

ZZZ

Instruction Manual

*P077053602*

077-0536-02

P5200A Series

High Voltage Differential Probes

ZZZ

Instruction Manual

xx

Revision B

www.tektronix.com

077-0536-02

protected by na

tional copyright laws and international treaty provisions.

Tektronix pro

ducts are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all

previously published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl B raun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit ww w.tek.com to ﬁnd contacts in your area.

Warranty

Tektronix warrants that this product will be free from defects in materials and workmanship for a period o f one (1) year from the date of

shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective

product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and

replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced

parts, modules and products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period

and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the

defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the

product to Customer if the shipment is to a location w ithin the country in which the Tektronix service center is located. Customer shall

be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and

care. Tektronix shall not be obligated to furnish service under this warranty a ) to repair damage resulting from attempts by personnel

other than Tektronix representatives to install, repair o r service the product; b) to repair damage resulting from improper use or

connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or

d) to service a product that has been modiﬁed or integrated with other products when the effect of such modiﬁcation or integration

increases the time or difﬁculty of servicing the product.

THIS WARRANTY IS GIVEN BY TE KTR ONIX W ITH RESPEC T TO THE PROD UC T IN LIEU OF A NY OTHE R WARRANTIES,

EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDO RS DISCLAIM ANY IMPLIED WARRANTIES O F MERCHANTAB ILITY OR

FITNESS FOR A PARTICULAR PURPOSE . TE KTRONIX' RES P ONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS

IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO T HE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX

AND ITS VENDORS W ILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIA L DAMAGES

IRRESPECTIVE O F WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH

DAMAGES.

[W2 – 15AUG04]

Table of Content

s

Table of Contents

General safety summary .......................................................................................... ... ... ... ... ... .... . iii

Compliance I

nformation ............................................................................................................... v

EMC Compliance................................................................................................................. v

Safety Compliance............................................................................................................... vi

Environmen

tal Considerations................................................................................................. viii

Preface................................................................................................................................. ix

Probe Operating Information.......................................................................................................... 1

Connectin

g to the Instrument.................................................................................................... 2

Probe Controls ...................................................................................................................5

Functional Check.... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .......................................... .7

Accessori

es............................................................................................................................ 8

Connecting to the Circuit... ... ....... ....... ... ... . ... ... ... ....... ....... ... ... ... . ... ... ....... ....... ... ... ... . ... ... ....... .. 8

Options................................................................................................................................ 23

Operatin

g Basics ..................................................................................................................... 24

Operating Characteristics and Probing Techniques . ... ... ... ... ... ... ... .. . .. ... ... ... ... ... ... ... ... ....................... . 24

Speciﬁcations .........................................................................................................................28

Warrant

ed Speci ﬁcations ....................................................................................................... 28

Typical Speciﬁcations ........................................................................................................... 29

Nominal Speciﬁcations.......................................................................................................... 31

Perfor

mance Graphs.. ........... ... ... ... .. ... ... ... ........... ........... ... ... ... ..... ... ... ... ........... ........... ... ... .. 32

Performance Veriﬁcation ............................................................................................................. 36

Required Equipment . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 36

Test Pr

ocedures .................. ... ... ... ... ... ... ... ... .. . .. ... ... ... ... ... ... ... ... .................... ... ... ................ 37

Adjustments........................................................................................................................... 41

Equipment Required ........................................................................................................... 43

Adjus

tment Procedures ... .............. ... .............. ... ... ... ... .. ... ... ... ... ... .............. ... .............. ... ... ... .. 44

Troubleshooting..... ... . .. . ... ... ... ... ... ... ... ... ... ... ... ... ... ............................ ... ... ... ... ... ......................... 55

Host Instrument Firmware ...................................................................................................... 55

Erro

r Conditions ... ............................ ... ... ... ... ............................ ... ... ... ... ... ... ... ... ... ... ... ... ... . .. 55

Cleaning .. ... ... ... ... ... ... ... ... ................... ... ... ... ................... ... ... ... ... ... ... ... ... ... . ... ... ... ... ... ..... 56

Service........................................................................................................................... 56

Ind

ex

P5200A Series H igh Voltage Differential Probes Instruction Manual i

Table of C ontent

s

ii P5200A Series High Voltage Differential Probes Instruction M anual

General safety s

ummary

General safet

y summary

Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it.

To avoid potential hazards, use this product only as speciﬁed.

Only qualiﬁed personnel should perform service procedures.

While using this product, you may need to access other parts of a l arger system. Read the safety s ections of the other

component manuals for warnings and cautions related to operating the system.

To avoid ﬁre or personal injury

Use proper power cord. Use only the power cord speciﬁed for this product and certiﬁed for the country of use.

Connect and disconnect properly. Do not connect or disconnect probes or test leads while they are connected

to a voltag

e source.

Connect a

nd disconnect properly.

Connect the probe output to the measurement instrument before connecting the

probe to the circuit under test. Connect the probe reference lead to the circuit under test before connecting the probe

input. D isconnect the probe input and the probe reference lead from the circuit under test before disconnecting the probe

from the m

easurement instrument.

Ground t

he product.

This product is indirectly grounded through the grounding conductor of the mainframe power cord.

To avoid electric shock, the grounding conductor m ust be connected to earth ground. Before making connections to the input

or output terminals of the product, ensure that the product is properly grounded.

Observe all terminal ratings. To avoid ﬁre or shock hazard, observe all ratings and markings on the product. Consult the

produc

t manual for further ratings information before making connections to the product.

Do not a

pply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal.

Power d

isconnect.

The power cord disconnects the product from the power source. Do not block the power cord; it

must remain accessible to the user at all times.

Do not operate without covers. Do not operate this product with covers or panels removed.

Do not operate with suspected failures. If you suspect that there is damage to this product, have it inspected by

qualiﬁed service personnel.

Avoid exposed circuitry. Do not touch exposed connections and components when power is present.

Use proper AC adapter. Use only the AC adapter speciﬁed for this product.

Do not operate in wet/damp conditions.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

P5200A Series H igh Voltage Differential Probes Instruction Manual iii

General safety s

ummary

Termsinthismanual

These terms may appear in this manual:

WARNING. Warning s tatements identify conditions or practices that could result in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.

Symbols and terms on the product

These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the marking.

WARNING indicates an injury hazard not immediately accessible as you r ead the marking.

CAUTION indicates a hazard to property including the product.

The following symbol(s) may appear on the product:

iv P5200A Series High Voltage Differential Probes Instruction M anual

Compliance Info

rmation

Compliance In

formation

This section lists the EMC (electromagnetic compliance), safety, and environmental standards with which the instrument

complies.

EMC Compliance

EC Declaration of Conformity – EMC (Applies Only to the P5200A Probe)

Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility. Compliance was demonstrated to the following

speciﬁcations as listed in the Ofﬁcial Journal of the European Communities:

EN 61326-1:2006, EN 61326-2-1:2006. EMC requirements for electrical equipment for measurement, control, and

laboratory use.

123

CISPR 11:2003. Radiated and conducted emissions, Group 1, Class A

IEC 61000-4-2:2001. Electrostatic discharge immunity

IEC 61000-4-3:2002. RF electromagnetic ﬁeld immunity

IEC 61000-4-4:2004. Electrical fast transient/burst immunity

IEC 61000-4-5:2001. Power line surge immunity

IEC 61000-4-6:2003. Conducted RF immunity

IEC 61000

-4-11:2004. Voltage dips and interruptions immunity

4

EN 61000-3-2:2006. AC power line harmonic emissions

EN 61000-3-3:1995. Voltage changes, ﬂuctuations, and ﬂicker

European contact.

Tektronix UK, Ltd.

Western Peninsula

Western Road

Bracknell, RG12 1RF

United Kingdom

1

This product is intended for use in nonresidential areas only. Use in residential areas may cause electromagnetic interference.

2

Emissions which exceed the levels required by this standard may occur whe

n this equipment is connected to a test object.

3

To ensure compliance with the EMC standards listed here, high quality shielded interface cables should be used.

4

Performance Criterion C applied at the 70%/25 cycle Voltage-Dip and the 0%/250 cycle Voltage-Interruption test levels

(IEC 61000-4-11).

Australia / New Zealand Declaration of Conformity – EMC

Complies with the EMC provision of the Radiocommunications Act per the following standard, in accordance with ACMA:

CISPR 11:2003. Radiated and Conducted Emissions, Group 1, Class A, in accordance with EN 61326-1:2006 and

EN 61326-2-1:2006.

P5200A Series H igh Voltage Differential Probes Instruction Manual v

Compliance Info

rmation

Safety Compliance

Equipment Type

Differential Voltage Probe

EC Declarati

on of Conformity – Low Voltage

Compliance was demonstrated to the following speciﬁcation as listed in the Ofﬁcial Journal of the European Communities:

Low Voltage Directive 2006/95/EC.

EN 61010-031/A1:2008. Safety requirements for electrical equipment for measurement, control and laboratory use - Part

031: Safety requirements for handheld probe assemblies for electrical measurement and test.

Canadian Certiﬁcation

CAN/CSA-C22.2 No. 61010-031-07/A1:2010, 1st Edition. Safety requirements for handheld probe assemblies for electrical

measurem

ent and test.

Additional Compliances

IEC 61010-031/A1:2008. Safety requirements for electrical equipment for measurement, control and laboratory use - Part

031: Safety requirements for handheld probe assemblies for electrical measurement and test.

Pollution Degree Description

A measure of the contaminants that could occur in the envir onment around and within a product. Typically the internal

envir

onment inside a product is considered to be the same as the external. Products should b e used only in the environment

for which they are rated.

Pollution Degree 1. No pollution or only dry, nonconductive pollution occurs. Products in this category a re generally

encapsulated, hermetically sealed, or located in clean rooms.

Pollution Degree 2. Normally only dry, nonconductive pollution occurs. Occasionally a temporary conductivity that is

caus

ed by condensation must be expected. This location is a typical ofﬁce/home environment. Temporary condensation

occurs only when the product is out of service.

Pollution Degree 3. Conductive pollution, or dry, nonconductive pollution that becomes conductive due to condensation.

These are sheltered locations where neither temperature nor humidity is controlled. The area is protected from direct

sun

shine, rain, or direct wind.

Pol

lution Degree 4. Pollution that generates persistent conductivity through conductive dust, rain, or snow. Typical

outdoor locations.

Pollution Degree

Pollution Degree 2 (as deﬁned in IEC 61010-1). Note: Rated for indoor use only.

vi P5200A Series High Voltage Differential Probes Instruction Manual

Compliance Info

rmation

Installation & Measurement (Overvoltage) Category Descriptions

Terminals on this product may have different installation or measurement (overvoltage) category designations. The

installation and measurement categories are:

Measurement Category IV. For measurements performed at the source of low-voltage installation.

Measurement Category III. For measurements performed in the building installation.

Measurement Category II. For measurements performed on circuits directly connected to the low-voltage installation.

Measurement Category I. For measurements perform ed on circuits not directly connected to MAINS.

Overvoltage Category (AC Adap ter)

Overvolta

ge Category II (as deﬁned in IEC 61010-1)

P5200A Series H igh Voltage Differential Probes Instruction Manual vii

Compliance Info

rmation

Environmental Considerations

This section provides information about the environmental impact of the product.

Product End-of-Life Handling

Observe the following guidelines when recycling an instrument or component:

Equipment recycling. Production of this equipment required the extraction and use of natural resources. The equipment

may contain s ubstances that could be harmful to the environment or human health if improperly handled at the product’s

end of life. To avoid release of such substances into the environment and to reduce the use of natural resources, we

encourage you to recycle this product in an appropriate system that will ensure that most of the materials are reused

or recycled appropriately.

This symbol indicates that this product complies with the applicable European Union r equirements according

to Directives 2002/96/EC and 2006/66/EC on waste electrical and electronic equipment (WE EE) and

batteries. For information about recycling options, c heck the Support/Service section of the Tektronix Web

site (www.tek.com).

Restriction of Hazardous Substances

This product has been classiﬁed as Monitoring and Control equipment, and is outside the scope of the 2002/95/EC RoHS

Directi

ve.

viii P5200A Series High Voltage Differential Probes Instruction Manual

Preface

This document provides operating information and speciﬁ cations for the Tektronix P5200A Series high voltage differential

probes. The probes share similar functions, properties, and operating procedures, and are discussed in the ﬁrstpartofthe

manual. The speciﬁcations and performance veriﬁcation procedures for the probes follow.

WARNING. Only use the accessories that are designed for your probe and that are rated at or above the voltages you are

measuring. (See Table i on page x.) (See Table ii on page xiii.)

Name Bandwidth Attenuation Oscilloscope interface

P5200A 50 MHz

50X/500X BNC

P5202A 100 MHz

20X/200X TekProbe BNC-Level 2

P5205A 100 MHz

50X/500X TekProbe BNC-Level 2

P5210A 50 MHz

100X/1000X TekProbe BNC-Level 2

P5200A Series H igh Voltage Differential Probes Instruction Manual ix

Preface

Figure i: P5200A High Voltage Differential Probe with accessories

Table i: P5200A, P5202A & P5205A probe standard accessories derating table

Combined probe and accessory common-mode voltage

and in

put voltag e -t o- earth ratings

Acce

ssory

P520

2A

P520

0A & P5205A

P521

0A

1

Extender leads

450

VCATI

300 V C AT II

100

0VCATII

600 V CAT III

230

0VCATI

1000 V CAT III

Hook clips (AC280-FL) 450 V CAT I

300 V C AT II

1000 V C AT II

600 V CAT III

1000 V CAT I

1000 V CAT III

Pincer clips (AC283-FL) 450 V C AT I

30

0VCATII

1000 V C AT II

60

0 V CAT III

1000 V CAT I

10

00 V CAT III

A

lligator clips (AC285-FL)

4

50VCATI

300 V C AT II

1

000VCATII

600 V CAT III

1

000VCATI

1000 V CAT III

1

The P5200A, P5202A & P5205A standard accessories can also be used with the P5210A probe, but only at the reduced voltage levels listed here.

x P5200A Series High Voltage Differential Probes Instruction Manual

Preface

Figure ii: P5202A High Voltage Differential Probe with accessories

P5200A Series H igh Voltage Differential Probes Instruction Manual xi

Preface

Figure iii: P5205A High Voltage Differential P robe with accessories

xii P5200A Series High Voltage Differential Probes Instruction Manual

Preface

Figure iv: P5210A High Voltage Differential Probe with accessories

Table ii: P5210A probe standard accessories derating table

Combined probe and accessory common-mode voltage

and in

put voltage-to-earth ratings

Acce

ssory

P520

2A

1

P520

0A & P5205A

1

P521

0A

Extender leads

450

VCATI

300 V C AT II

100

0VCATII

600 V CAT II

230

0VCATI

1000 V CAT III

Test probe (TAT P) 450 V C AT I

300 V C AT II

1000 V C AT II

600 V CAT II

1000 V CAT I

1000 V CAT II

Small hook tip (TASH) 450 V CAT I

30

0VCATII

1000 V C AT II

60

0VCATII

2300 V CAT I

10

00 V CAT II

L

arge hook tip (TALH)

4

50VCATI

300 V C AT II

1

000VCATII

600 V CAT II

2

300 V CAT I

1000 V CAT II

1

The P5210A standard accessories can be used with these probes at the reduce d voltage levels listed in this table.

P5200A Series H igh Voltage Differential Probes Instruction Manual xiii

Probe Operating

Information

Probe Operati

ng Information

The P5200A Series probes share many common features, including connections to the circuit, compensation box buttons,

and operating basics. The probes connect to the host oscilloscope through one of two probe-to-oscilloscope interfaces:

BNC – this connection is a shielded 50 Ω coaxial cable with an outer ground connection and center signal pin. The BNC

interface is used on the P5200A probe, which allows you to c onnect directly to most g round-re ferenced oscilloscopes.

TekProbe

Level 2 – this interface adds probe communications with the oscilloscope to accomplish calibrated offset at

the probe tip. This interface is used on the P5202A, P5205A, and P5210A probes, and many Tektronix oscilloscopes.

These probes can also be used with Tektronix oscilloscopes that use the TekVP I-interface, by connecting through an

optional

TPA-BNC Adapter.

TPA-BNC Adapter

The TPA-BNC Adapter is an optional accessory that enables you to use existing TekProbe-interface probes with oscilloscopes

that feature the TekVPI probe interface. The adapter recognizes TekProbe-interface probes and supplies the necessary

power, serial c ommunication, and offset control as used by the connected TekProbe product accessory.

WARNING. To reduce risk of shock or ﬁre, do not exceed the ratings of the TPA-BNC adapter; it is not intended to be

connected to voltages above 30 VAC, 42 Vpk, or 60 V DC. For BNC probes, connect the probe directly to the oscilloscope.

1 P5200A Series High Voltage Differential Probes Instruction Manual

Page is loading ...

Tektronix P5200A, P5202A, P5205A, P5210A User manual

Related papers

Other documents