Whirlpool Aquafeel 1600 Program Chart

Type
Program Chart
GB AQUAFEEL 1600 PROGRAMME CHART
5019 301 05762
Whirlpool is a registered trademark of Whirlpool USA
M0501
- tested and approved by The Woolmark Company -
: optional / Yes : dosing required
1)
For improved garment care spin speed is restricted to 1000 rpm in this programme.
2)
In this programme default spin speed can be increased till 400 rpm.
3)
For improved garment care spin speed is restricted to 1400 rpm in this programme.
Programme
Care
Labels
Type of wash/Notes
Max
Load
Detergents and additives Special options Max
Spin
Speed
rpm
Tempe-
rature
°C
Softener Main
Wash
Prewash Start Delay
Start
selectie uren
Départ
différé
Easy
Ironing
Eco
Plus
Prewash Intensive
Rinse
Rinse
Hold
Spin
Speed
Reduction
kg
Cotton
Katoen / Coton
Normally to heavily soiled bed linen, table linen and underwear, towels,
shirts etc. made of cotton, coloured cotton and linen.
For temperature selection, please respect the manufacturer's
recommendation on the care label.
With heavily soiled laundry the additional “Prewash” option can be selected as well.
6.0
Ye s
❉❉
1600 20 to 95
Synthetics
Synthetisch / Synthétique
Normally to heavily soiled blouses, shirts, overalls etc. made of polyester
(Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton.
2.5
Ye s
❉❉
1)
1000
1)
20 to 60
Daily
Gemengde was
/
Slightly to normally soiled textiles made of cotton and/or synthetics.
3.0
Ye s
❉❉
——
❉❉
3)
1400
3)
30 to 60
Superrapid
Snel / Chrono
Shortly worn outer clothing made of cotton, polyester, polyamide and
blends with cotton.
3.0
Ye s
❉❉
——
❉❉
3)
1400
3)
20 to 30
Delicates
Fijne was / licat
Curtains and delicate clothing, dresses skirts, shirts and blouses.
1.5
Ye s
❉❉
——
1)
1000
1)
20 to 40
Wool
Wol / Laine
Only woollens, labelled with the woolmark and identified as machine
washable.
This programme (40°C) is tested and approved by The Woolmark
Company for machine washable wool.
If you select “Rinse Hold” do not leave items to soak for too long.
1.0
Ye s
——
1)
1000
1)
20 to 40
Handwash
Handwas / Lavage main
Textiles made of silk, linen, wool and viscose marked as “handwashable”.
This programme (40°C) is tested and approved by The Woolmark
Company for handwashable wool.
If you select “Rinse Hold” do not leave items to soak for too long. A very
gentle spin is used in this programme.
1.0
Ye s
——
2)
400
2)
20 to 40
Rinse + Spin
Spoelen + Centrif.
Rinçage + Essorage
Same as the last rinse and the final spin in the “Cotton” programme.
6.0
——
❉❉
——
❉❉
1600
Spin
Centrif. / Essorage
In this programme spinning is intensive. Same as the spin cycle in the
“Cotton” programme.
6.0
——
——
1600
Gentle Spin
Kort centrif. / Essorage doux
In this programme spinning is gentle. Same as the spin cycle in the “Wool”
programme.
1.5
——
——
1)
1000
1)
Drain
Afpompen / Vidange
Drain only - no spinning. Alternative method of terminating programme after
“Rinse Hold”.
——
6
th
Sense
intelligent technology always guarantees perfect results with maximum efficiency whatever
the wash load.
This washing machine is equipped with
automatic safety functions which detect
and diagnose faults at an early stage and
react appropriately, e.g.:
A. “Water tap closed” indication
B. “Clean pump” indication
C. “Door locked” indication
D. Programme selector knob
E. Programme sequence indication
F. Temperature selection button
G. “Start/Pause” button
H. “Start/Pause” indication
I. “Start Delay” button
J. “Start Delay” indication/
“Remaining Time” display
K. “Reset” button
L. “Spin Speed” button
Selecting any option the indication lights
up. When the combination of programme,
additional options and temperature is not
possible, the indication lights switch off
automatically. Unsuitable combinations of
options are deselected automatically.
B
H
E
F
G
A
C
I J KL
D
30105762GB.fm Page 1 Friday, July 8, 2005 3:07 PM
Black process 45.0° 100.0 LPI
5019 301 05762
Whirlpool is a registered trademark of Whirlpool USA
Add the detergents as described in the programme
table or in the chapter “Detergents and Additives”
in the booklet.
1. Turn the
programme selector knob
to the
desired programme.
2. The
remaining time display
shows the
duration of the chosen programme (in hours and
minutes) and the indication of the
“Start/
Pause”
button is flashing.
3. The
programme sequence
and the predefined
spin speed indication
corresponding to the
selected programme lights up.
The recommended temperature (see the
indicator) can be altered by pressing “
+
/-” button.
Selecting any option the indication lights up.
When the combination of programme, additional
options and temperature is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Easy Ironing” button
Can be used together with “Cotton”, “Synthetics”
and “Daily” programmes to make ironing easier.
Increases the water quantity and the clothes are
spun very soft.
“Eco Plus” button
With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption can be achieved.
“Prewash” button
Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
“Intensive Rinse” button
More water and a longer time in rinse cycle is added.
This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse Hold” button
The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
This option is particularly recommended for the
programme “Synthetics”, “Daily” and “Delicates”.
This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note:
The programme stops to “Rinse Hold” at
the time the “Rinse Hold” light in the programme
sequence indication is on.
Terminate the “Rinse Hold” option:
Press the “Rinse Hold” button again; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
CONSUMPTION DATA
Programme
Temperature
Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton 95 6.0 54** 1.90 2:00
Cotton 60 6.0 49 1.14 2:20
Cotton with “Eco plus”*** 60 6.0 49 1.02 2:30
Cotton 40 5.0 44 0.60 2:05
Synthetics 60 2.5 55 0.80 1:30
Synthetics 40 2.5 55 0.60 1:20
Daily 40 3.0 45 0.50 1:00
Superrapid 30 3.0 37 0.40 0:30
Delicates 30 1.5 60 0.50 0:45
Wool 30 1.0 60 0.30 0:40
Handwash 30 1.0 45 0.30 0:40
Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in compliance with
Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply
pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
If you do not wish to spin the clothes, turn the
programme selector knob counterclockwise to
the “Drain” programme and press the
“Start/Pause”
button again when the indication
next to it is flashing.
“Spin Speed” button
Every programme has an automatic predefined
maximum spin speed.
Press the button to set another spin speed.
If the spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
Select programme, temperature and options.
Press the “Start Delay” button to select the delay
time by 1 to 23 hours;
Press the
“Start/Pause”
button.
The indication next to the “Start Delay” button
lights up and goes off when the programme starts.
The time delay indication disappears when the
programme starts and it is replaced by the
remaining time.
The number of hours preselected can later be
reduced pressing again the “Start Delay” button.
To cancel the “Start Delay
..before you press the “Start/Pause” button:
Turn the programme selector to the
Off
/0”
position.
Reselect the desired programme and options and
press
“Start/Pause”
button to start the programme.
..after having pressed the “Start/Pause” button:
Press the “Reset” button for at least 3 seconds -
the start delay time disappears from the
remaining time indication,
then either start the chosen programme by
pressing the
“Start/Pause”
button twice
or turn the programme selector knob to the
Off/0” position and chose another programme.
Open the tap and press the
“Start/Pause”
button. The
indication next to the
“Start/Pause”
button lights up.
The indications show the sequence reached in the
programme. After starting the programme, the
sequence indication runs from left to right through
Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding indication goes out.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Door locked”
As long as a washing programme is running, the lamp
lights up to show that the door cannot be opened. When
the indication goes off, the door can be opened again.
The remaining time is on “0:00” and all the lights
of the programme sequence indication are off.
1. Turn the programme selector to the
Off
/0”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry out.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the
“Start/Pause”
button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
The
“Reset”
button cancels a programme
before the end.
Press the
“Reset”
button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
RED INDICATIONS
PROGRAMME END
CHANGE THE PROGRAMME,
TEMPERATURE, OPTIONS AFTER
PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30105762GB.fm Page 2 Friday, July 8, 2005 3:07 PM
Black process 45.0° 100.0 LPI
  • Page 1 1
  • Page 2 2

Whirlpool Aquafeel 1600 Program Chart

Type
Program Chart

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI