Aegis 8250 Quick Manual

Brand: Aegis

Model: 8250

Type: Quick Manual

This manual is also suitable for

8250FF

TECHNICAL SUPPORT IS AVAILABLE MON-FRI

7:30AM-3:30PM PST AT 1-888-678-7224

by Pach & Co. Quick Guide

 Parts above are only

included on complete

system (8250)

 Missing Parts, contact Pach

and Company 1-888-678-

7224

 Defective system under

manufacturer warranty,

call 1-888-678-7224 for

advance replacement

 24 Months warranty

for

complete system

 6 Months warranty

for

Printed Circuit Board

(8PCB250)

 Manuals, management

software, catalog are on CD

or download at www.pach-

co.com

Red button is Master Code retrieval button. See also diagram.

What is Master Code: 4- digit code to log-on to programming mode

(0000 is default)

What is Dir (directory code): 2, 3, or 4 digit number see function

code 09. The number can be associated to apartment no., first three

digit of phone no., last four digit of phone no. , or any random no.

assigned to each tenants. Every tenant must have different directory

code no..

What is Access Code: 4-digit code for tenant to open the door or

gate.

Exit program, clear field,

reset keystroke.

17 Set system date

Save program 19

Initialize event recording

buffer

Change master code

(0000 is default)

Remote unlock relay 1

(1-9, 9 is default)

01 Add new tenant 21

Remote unlock relay 2

(1-9, 8 is default)

02 Edit existing tenant 40

Master code mask.

Warning: read manual

for more detail.

03 Delete existing tenant 46

Display system’s

information

04 Clear all tenants 50

Clear memory to factory

default

Manual unlock/lock relay 1

with timer (01-98 hours, 99

hours unlock hold, 00

hours to lock)

Select Modem Protocol

V22 or B212

06 Manual unlock/lock relay 2 71 Enable Disable Modem

Single or multi system

(single is default)

Invalid code lock-out

count (1-9). 3 is default

08 System ID number (n/a) 73

Tone/pulse dialing.

Tone is default

Directory digit (2, 3 or 4

digit, 3 digit is default)

Enable/disable auto

answer. Enable is

default

10 Edit scrolling message 75

Enable/disable keypad

press beep. Enable is

default

Relay 1 unlock interval

(04-99 seconds, 12

seconds is default)

Enable/disable speaker

beep. Enable is default

12 Relay 2 unlock interval 77

Enable/disable PBX.

Disable is default

14 Set system clock 78

View name and

directory

15 Day light saving 79

Talk time (10-180

seconds). 60 second is

default

16 Display current time 91

Total number of tenant.

Tenant with no name

will not be included

Log on to programming: Press

simultaneously then release, welcome

message will stop scrolling (repeat if screen

still scrolls) enter 4-digit “MASTER CODE”

(0000 is default), the screen will show:

Select the “Function Code” from the table

Two ways call from the system

1. Press

to scroll name from A-Z or to scroll name from

Z-A then press

to call name selected.

2. Press

wait for dial tone then press the directory no.

Opening the door remotely

press to release relay 1

(door 1) or to release relay 2 (door 2).

Opening the door using the access code

press (display

screen will stop scrolling) then press a valid 4-digit access

code.

Extending talk time tenant must press from the phone

after the time out warning beep.

Calling into the system

: incase you are not available when

your visitor call you. Follow steps below to use this feature

1. The system modem must be disabled and function 74 (auto

answer must be enabled).

2. Call the system’s phone no., you will hear “ONE BEEP”, then

press

to talk to your visitor. Press or to release

the door

1. Press after selecting a letter or character.

2. You have 30 seconds to enter each letter or character.

3. Letter QZ, numeric 0-9 and punctuations press

4. Press

space and for backspace

COMPLETE MANUALS ARE ON CD PROVIDED OR DOWN LOAD ON LINE AT www.pach-co.com

1. EARTH GROUND

16 gauge- single solid wire to

ground the system. If the

system has been struck by

lightning multiple times, try to

remove the earth ground.

2. TELEPHONE LINE

Cat 5 twisted pair (from the

telephone company dial

tone), maximum distance 200

feet. If you encounter static or

radio interference:

 Remove the earth ground

 Install a DSL filter in series

with the phone line.

 Install RF filter

 Contact the radio station,

they may have a solution

3. DOOR STRIKE/GATE

The system has two

independent on board relays

(125VAC 12A, 250VAC 7A,

and 30VDC 7A). 18 gauge 2-

conductors stranded wire for

each door. An isolation relay

with separate power supply is

recommended for magnetic-

lock. Installation to eliminate

spikes. See diagram for

wiring connections, also refer

to door strike or gate operator

owner’s manual.

4. POSTAL LOC

Postal switch blue and yellow wires

are connected to the terminal pins

POST and LCOM

 Postal input only works for relay 1.

 Postal switch and knock-out are

provided. Call the local post office

for installing the postal lock

 POST and LCOM input can also

be used for free exit switch, loop

detector or any device with dry

contact output.

5. POWER

12Vac 40VA supplied or 12Vdc

3A not supplied. Use at least 18

gauge 2 conductors stranded

wires for power. The voltage

measurement must be in the

range of :

12.5Vac-14Vac--12Vac power

13.5Vdc-14Vdc-- 12Vdc power

Warning: If you have low voltage

issue, do not use higher voltage

transformer or power supply, to do

so will damage the system.

Install surge protector (ASP1) or UPS

for power and telephone to protect the

system from power surges.

6. BATTERY BACKUP

Optional battery backup is

needed to keep the system

in operational during the

power outages. Use

ABAT1 (12Vdc 4.5Ahr, last

for 3-4 hours). Use 18

e 2 conductors

7. NIGHT LIGHTS

The night lights turn on

24/7, prewired to +12V and

LCOM.

Warning: DO NOT USE

+12V and LCOM terminal

pins for input power.

8. KEYPAD AND LCD RIBBON

CABLE

Ribbon cables must be plugged in

as shown on diagram with the red

line dots are on top.



Prior removing the knock-out, any

drilling or grinding during the

installation removes the board.

 Always turn the system off if you are

doing service.

 Place ribbon cables on the side before

closin

the

anel’s door.

Aegis 8250 Quick Manual

Brand: Aegis

Model: 8250

Type: Quick Manual

This manual is also suitable for

8250FF

Download PDF

report

Aegis 8250 Quick Manual

This manual is also suitable for

Aegis 8250 Quick Manual

Other documents