ARX e-pre
The e-pre is a versatile audio tool that can be used for a variety of applications, including:
- Microphone preamplifier: The e-pre can be used to amplify the signal from a microphone, making it ideal for recording vocals, instruments, or other audio sources.
- Guitar preamp: The e-pre can be used as a guitar preamp, providing a range of tones from clean to overdriven.
- Voice-over preamp: The e-pre can be used as a voice-over preamp, providing a rich, warm sound that is perfect for narration, podcasts, and other voice-over applications.
The e-pre is easy to use, with a simple and intuitive front panel layout. The controls include:
ARX e-pre
The e-pre is a versatile audio tool that can be used for a variety of applications, including:
- Microphone preamplifier: The e-pre can be used to amplify the signal from a microphone, making it ideal for recording vocals, instruments, or other audio sources.
- Guitar preamp: The e-pre can be used as a guitar preamp, providing a range of tones from clean to overdriven.
- Voice-over preamp: The e-pre can be used as a voice-over preamp, providing a rich, warm sound that is perfect for narration, podcasts, and other voice-over applications.
The e-pre is easy to use, with a simple and intuitive front panel layout. The controls include:
QUICKSTART CARD
(a.k.a. “Sorry Guys I can’t wait to read the manual!”)
OK, we know what it’s like - it’s hard to sit down and read all the
instructions for this brand new audio tool when you can’t wait to get
started.
So for all you eager beavers here’s the short form ‘get-you-started’
info. It assumes that you already have your sound card installed and
your audio software configured. If you haven’t, then do that first
1. Unpack the
e-pre from its packaging
2. Make sure your computer is turned OFF, pop the cover off (this may
require a screwdriver) then find an empty 5¼” slot on your computer
chassis. The one you used to have your 5¼” floppy drive in will do
just fine
3. Slide the
e-pre into the spare slot. There are screw holes on each
side of it. Use the screws supplied to firmly locate the
e-pre in the
slot (One screw per side is enough. If access to both sides of the slot
is awkward, then two screws on one side will be OK)
4. Decide which output connections from the
e-pre you are going to
use, and connect a lead from them to the LINE input(s) of your sound
card.
5. Plug a spare computer power supply connector (a big flat one with 4
round pins) into the rear of the
e-pre, then close the lid of the compu-
ter.
That’s about it for installation. Plug a microphone into the front panel
combo input of the e-pre, then turn the computer on and open up your
audio software program. Select RECORD from the appropriate menu
and you’re on your way.
See over for QuickTips !
e-pre
e-pre QuickTips
1. Start with all the e-pre controls at 12 o’clock.
2. If the OVERLOAD LED on the front of the
e-pre flashes as you record,
back off the INPUT GAIN control.
3. If the recording meters on your software are going into the RED, re-
duce the OUTPUT LEVEL until they stay in the green or yellow area.
4. Adjusting the CONTOUR control will either boost the MIDs (turn LEFT)
or LOW and HIGHs (turn RIGHT). These will affect the OUTPUT
level, so always check it after a change.
5. Instant guitar Preamp - turn CONTOUR hard left
6. Instant radio Voice-over setting - turn CONTOUR hard right
Have fun!
The
ee
ee
e
-pre-pre
-pre-pre
-pre team
Front Panel
Rear Panel
-
1
ARX e-pre
The e-pre is a versatile audio tool that can be used for a variety of applications, including:
- Microphone preamplifier: The e-pre can be used to amplify the signal from a microphone, making it ideal for recording vocals, instruments, or other audio sources.
- Guitar preamp: The e-pre can be used as a guitar preamp, providing a range of tones from clean to overdriven.
- Voice-over preamp: The e-pre can be used as a voice-over preamp, providing a rich, warm sound that is perfect for narration, podcasts, and other voice-over applications.
The e-pre is easy to use, with a simple and intuitive front panel layout. The controls include:
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI