Harman JBL CI55RA Owner's manual

Harman
Brand
Harman
Model
JBL CI55RA
Category
Car speakers
Type
Owner's manual

Harman JBL CI55RA is a 2-way in-ceiling speaker with a 5 1/4" Kevlar cone woofer and a 25mm silk dome tweeter. It has a power of 100W RMS and an impedance of 8 Ohms. The frequency response is 70Hz to 20KHz and the sensitivity is 85dB (@1W/m).

This speaker is perfect for use in a variety of applications, including home theater, distributed audio, and commercial sound. It can be used to create a wide soundstage with clear highs and deep bass. The adjustable angle allows you to direct the sound where you need it, and the paintable grill allows you to match the speaker to your décor.

Here are some of the features and benefits of the Harman JBL CI55RA:

Harman JBL CI55RA is a 2-way in-ceiling speaker with a 5 1/4" Kevlar cone woofer and a 25mm silk dome tweeter. It has a power of 100W RMS and an impedance of 8 Ohms. The frequency response is 70Hz to 20KHz and the sensitivity is 85dB (@1W/m).

This speaker is perfect for use in a variety of applications, including home theater, distributed audio, and commercial sound. It can be used to create a wide soundstage with clear highs and deep bass. The adjustable angle allows you to direct the sound where you need it, and the paintable grill allows you to match the speaker to your décor.

Here are some of the features and benefits of the Harman JBL CI55RA:

CI55RA - 2-WAY IN CEILING SPEAKER
Harman Consumer, Inc.
8500 Balboa Boulevard, Northridge, CA 91329 USA
www.jbl.com
© 2017 HARMAN International Industries, Incorporated.
All rights reserved. Harman do Brasil Indústria Eletrônica e Participações Ltda. is a trademark of Harman International Industries,
registered in the United States and/or other countries. Features, specifications and appearance are subject to change without notice.
1. TAKE DE GRILL OUT SO THAT THE
MOUNTING SCREWS ARE EXPOSED
4. ANGLE ADJUSTMENT
5. FIXED THE SPEAKER
6. DISASSEMBLE THE SPEAKER
2. CONFIRM THE INSTALLATION
LOCATION SIZE
3. CONNECTION
Cód.: 030142 - Rev.: 00 - 07/17
Remove the speakers from the
wall or the ceiling, loosen the
screws enough to remove the
speaker.Be careful to prevent the
loss of the mounting legs.
mounting
legs
After adjusting the angle to the proper
position, tighten the left and right scre
-ws with a Phillips screwdriver to ensure
that it does not slide. Use a wrench to
externally rotate the mounting legs
and fix the speaker to the wall or ceiling.
Make sure that the mounting legs are
fixed on the wall or on the ceiling. Be
careful not to tighten the screws over
and then cover the grill.
Can rotate
15 to 45 degrees
Remark: the angle can be adjusted
between 15 to 45 degrees.
Use a Phillips screwdriver to loosen the
left and right 2 screws (shown above)
inside the inner frame, and then push
the middle puller (shown bellow) to
adjust the angle.
Connect the positive terminal of
the amplifier output signal to the
red terminal of the crossover and
the negative terminal to the black
terminal.
Technical Specifications
Tweeter 25mm-Silk Dome
5 1/4" Cone Kevlar
Woofer
Power 100W RMS
8 Ohms
70Hz - 20KHz
Impedance
Weight
Freq. response
Sensibility 85dB
(@1W/m)
3.0Kg
Remove the grill first, insert the iron
speaker into the grill and then pull
up or pushed up the mounting legs
carefully until the edge of grill come
up.
Remove the inner square anti-paint
board from the supplied square tem
-plate and keep it well for later use.
Use the inner ring part of square anti
-paint board to mark the size and
position of the mounting hole.
Make sure that the mounting legs
are inward spin. Put the speaker
into the excavated empty hole.
11.6"
9.72"
15.74"
13.89"
TEMPLATE FOR INSTALLATION HOLE
CUT ALONG THE DASHED LINE
Dimensions for ceiling cutting
Harman Consumer, Inc.
8500 Balboa Boulevard, Northridge, CA 91329 USA
www.jbl.com
CI8R - CAIXA DE EMBUTIR - 2 VIAS
Manual do Proprietário - Por favor leia o manual antes de utilizar o equipamento.
Especificações Técnicas
Tweeter 25mm-Silk Dome
5 1/4" Cone KevlarWoofer
Potência
8 Ohms
70Hz - 20KHz
85dB
Impedância
Peso
Resposta Freq.
Sensibilidade (@1W/m)
100W RMS
3,0Kg
Cód.: 030142 - Rev.: 00 - 07/17
1. RETIRE A GRADE, EXPONDO OS
PARAFUSOS DE MONTAGEM
INSTALAÇÃO
4. AJUSTE DO ÂNGULO
5. FIXANDO O PRODUTO
6. REMOVENDO O PRODUTO
2. PREPARANDO O LOCAL
DE MONTAGEM
3. CONECTANDO OS FIOS
DO ALTO-FALANTE
Ajuste de 15 a 45 graus
Para remover a grade, insira o clips
em uma das aberturas da grade e
puxe-a para fora. Ou empurre a
estrutura plástica até que a grade se
destaque da moldura.
Remova e guarde o disco de papelão
interno do molde/máscara de pintura
fornecida. Utilize a porção interna
como molde para marcar o tamanho
do furo que deve ser feito e o local
para montagem do alto-falante.
Certifique-se de que as abas de
montagem estejam viradas para
dentro, permitindo que o alto-falante
se encaixe no furo de montagem.
Conencte o terminal positivo da saída
de sinal do amplificador ao terminal
vermelho do crossover e o terminal
negativo ao terminal preto.
Utilizando uma chave Phillips solte os
parafusos da moldura interna (conforme
figura acima) para ajustar o ângulo.
O ângulo pode ser ajustado entre 15 e 45
graus.
Após o ajuste adequado de ângulo, aperte
os parafusos com uma chave Phillips para
garantir que a moldura interna não se
mova, alterando o ângulo. Certifique-se de
que as abas de montagem estejam viradas
para dentro, permitindo que o produto se
encaixe no furo. Então, insira o produto no
furo de montagem.
Utilize os quatro parafusos para fixar as
abas de montagem no parede ou teto,
cuidando para não apertar demais os
parafusos. Recoloque a grade.
Para remover, solte os parafusos apenas o
suficiente para retirar o produto, isto evita a
perda das abas de montagem.
Abas de
montagem
! IMPORTANTE !
Caso haja um ícone no fim do parágrafo,
consulte as informações pertinentes na caixa
com o ícone correspondente naquela página.
- Aviso
- Importante
- Cuidado
- Dica
- Nota
NOTA
Não pinte o componente alto-falante.
Recomendamos que você utilize spray na
grade para que a tinta não bloqueie os furos.
NOTA
Evite a passagem dos fios do alto-falante em
locais próximos a fios elétricos.
Não grampeie ou pregue os fios do alto-falante.
CUIDADO
Cuidado para não cortar a fiação ou tubulação
existente na parede.
295mm
247mm
400mm
353mm
Dimensões para recorte do forro
PARA RECORTAR O FO RRO UTILIZAR A LINH A TRACEJADA
2017 HARMAN International Industries, Incorporated.
Todos os direitos reservados. Harman do Brasil Indústria Eletrônica e Participações Ltda
é marca registrada da Harman International Industries, Incorporated registrada nos EUA
e/ou outros países. Características, especificações e aspectos estéticos estão sujeitos a
alterações sem prévio aviso.
  • Page 1 1
  • Page 2 2

Harman JBL CI55RA Owner's manual

Harman
Brand
Harman
Model
JBL CI55RA
Category
Car speakers
Type
Owner's manual

Harman JBL CI55RA is a 2-way in-ceiling speaker with a 5 1/4" Kevlar cone woofer and a 25mm silk dome tweeter. It has a power of 100W RMS and an impedance of 8 Ohms. The frequency response is 70Hz to 20KHz and the sensitivity is 85dB (@1W/m).

This speaker is perfect for use in a variety of applications, including home theater, distributed audio, and commercial sound. It can be used to create a wide soundstage with clear highs and deep bass. The adjustable angle allows you to direct the sound where you need it, and the paintable grill allows you to match the speaker to your décor.

Here are some of the features and benefits of the Harman JBL CI55RA:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents