American Standard 0954.000.020 Installation guide

Category
Car kits
Type
Installation guide

American Standard 0954.000.020 is a wall-hung basin designed for both residential and commercial use. Crafted from durable vitreous china, it features a sleek and modern design that complements various bathroom styles. This basin is suitable for use with concealed arm support systems, offering a clean and minimalist look. Installation requires careful attention to local plumbing and building codes to ensure proper functioning. With its high-quality construction and versatile design, the American Standard 0954.000.020 basin provides a stylish and functional addition to any bathroom space.

American Standard 0954.000.020 is a wall-hung basin designed for both residential and commercial use. Crafted from durable vitreous china, it features a sleek and modern design that complements various bathroom styles. This basin is suitable for use with concealed arm support systems, offering a clean and minimalist look. Installation requires careful attention to local plumbing and building codes to ensure proper functioning. With its high-quality construction and versatile design, the American Standard 0954.000.020 basin provides a stylish and functional addition to any bathroom space.

SAVE FOR FUTURE USE
730464-110 Rev. A
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2012
NOTE: Pictures may not exactly define contour of china and components.
MURRO WALL HUNG BASIN
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
!
OBSERVE LOCAL PLUMBING AND BUILDING CODES
For residents of the United States, warranty
information may also be obtained by calling the
following toll free number: (800) 442-1902
www.americanstandard-us.com
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
In Canada:
AS Canada ULC
5900 Avebury Ave.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: (800) 387-0369
www.americanstandard.ca
In Mexico:
Customer Service Manager
AS Maquila, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com/mx
Provide
Rough-In:
Install
Mounting
Bolts:
Level
Basin
and
Mark
Screw
Locations:
Install
Fittings:
Mount
Basin:
Connect
Supplies:
Mount
Pedestal:
Install waste pipe. Space supplies (hot/cold screwdriver
stops) 1-5/8" (41mm) to either side of centre. Firmly
attach two 2" x 8" (50 x 203 mm) wood braces to wall
studs. Bottom of brace should be 26-1/2" (673 mm) up
for floor and extend a minimum of 12" (305 mm) to
either side of waste. Complete drywall installation (see
Figure 1).
Mark locations of 4" (102 mm) mounting lag bolts 4-1/4"
(108 mm) to either side of centre. Pre-drill mounting
holes then fasten lag bolts and washers supplied. Allow
each bolt head to protrude 1-1/4" (32 mm) from finished
wall.
Mount basin on protruding lag bolts and level. Mark
basin anchor holes. If semi-pedestal/shroud is desired
(ordered separately), position it under lips at bottom of
basin and mark anchor holes. Set fixtures aside.
Pre-drill anchor holes in wall where marked, drilling
semi-pedestal/shroud holes at a 45˚ angle toward
centre.
Install faucet and waste assembly according to
manufacturer’s instructions before installing basin.
Remount basin on lag bolts and secure with 2" (51mm)
wood screws and washers provided. Firm up lag bolts
but do not over-tighten.
Connect hot/cold supplies and drain pipe. Bend flexible
supplies to clear opening in semi-pedestal/shroud. Turn
on water. Check for leaks.
Reposition semi-pedestal/shroud. Secure to wall using
2" (51 mm) screws and washers provided.
L
C
12"
(305mm)
12"
(305mm)
DRYWALL
DOUBLE
2" x 8"
(50 x 203mm)
WOOD BRACE
4-1/4"
(108mm)
8-1/2"
(216mm)
MOUNTING
LEG BOLTS
SUPPLIES
WASTE
FINISHED FLOOR
FINISHED FLOOR
CONCEALED ARM
CARRIER HOLES
BASIN ANCHOR
HOLES
SLOTS FOR
BASIN LEG BOLTS
BEND FLEXIBLE
SUPPLY
TUBES
WASTE
SEMI-PEDESTAL/SHROUD
ANCHOR HOLES
FIGURE 1
FIGURE 2
FIGURE 3
26-1/2"
(673mm)
3-3/4"
(63mm)
7-1/2"
(191mm)
7-3/4"
(197mm)
9-3/4"
(248mm)
32-1/2"
(826mm)
*31-1/2"
(800mm)
*IN ONTARIO
34"
(864mm)
*33"
(838mm)
*IN ONTARIO
10"
(254mm)
BARRIER FREE
FOR CONCEALED ARM SUPPORT, REFER TO CARRIER MANUFACTURER’S INSTRUCTIONS
BARRIER FREE, UNIVERSAL ACCESS INSTALLATION:
For Universal Design Options, top of front rim may be mounted at
813 mm (32") from the finished floor to meet ADA and ANSI A117.1
requirements, except in Ontario and California. In Ontario, the code
requires a height of 838 mm (33"). 864 mm (34") is required for
California Title 24 (see Figure 3). Check local codes.
Suggested Tools and Supplies:
Adjustable wrench, 3/4" socket wrench, No. 3 Philips screwdriver, pliers,
rule, carpenter level, drill, 1/8" (3 mm) dia. & 3/8" (10 mm) dia. drill bits,
basin faucet, hot/cold screwdriver stop, and drain assembly.
CUSTOMER SERVICE INFORMATION
1 / 1

American Standard 0954.000.020 Installation guide

Category
Car kits
Type
Installation guide

American Standard 0954.000.020 is a wall-hung basin designed for both residential and commercial use. Crafted from durable vitreous china, it features a sleek and modern design that complements various bathroom styles. This basin is suitable for use with concealed arm support systems, offering a clean and minimalist look. Installation requires careful attention to local plumbing and building codes to ensure proper functioning. With its high-quality construction and versatile design, the American Standard 0954.000.020 basin provides a stylish and functional addition to any bathroom space.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document