Page is loading ...
Owner's manual
MAGNETIC CYCLE
ME
HO
PEC-2035 SERIES HOME MAGNETIC CYCLE ASSEMBLY INSTRUCTION
THIS OWNER'S MANUAL CONTAINS ASSEMBLY, OPERATION, MAINTENANCE AND SAFETY
INFORMATION. IN THE INTEREST OF SAFETY, PLEASE MAKE CERTAIN THAT YOU READ
AND UNDERSTAND ALL THE INFORMATION BELOW.
IMPORTANT SAFETY PRECAUTIONS
1. READ THE OWNER'S MANUAL AND ALL ACCOMPANYING LITERATURE AND FOLLOW IT
CAREFULLY BEFORE USING YOUR MACHINE.
2. THIS MACHINE IS INTENDED FOR HOUSEHOLD USE ONLY. IT IS NOT DESIGNED FOR
COMMERCIAL USE.
3. INSPECT YOUR EXERCISE MACHINE PRIOR TO EXERCISING TO ENSURE THAT ALL
NUTS AND BOLTS ARE FULLY TIGHTENED BEFORE EACH USE.
4. MAKE SURE MACHINE IS STABILIZED ON THE FLOOR AND UNEVEN SURFACES ARE
LEVELED BEFORE USE.
5. MOST EXERCISE EQUIPMENT IS NOT RECOMMENDED FOR SMALL CHILDREN.
CHILDREN SHOULD NOT USE THE MACHINE UNLESS THEY ARE UNDER ADULT
SUPERVISION.
6. EXERCISE EQUIPMENT HAS MOVING PARTS. IN THE INTEREST OF SAFETY, KEEP
OTHERS, ESPECIALLY CHILDREN, AT A SAFE DISTANCE WHILE EXERCISING.
7. MAKE SURE ALL ADJUSTMENT DEVICES ARE FULLY INSERTED AND PROPERLY
ADJUSTED BEFORE USE TO AVOID INJURY.
8. REMOVE ALL JEWELRY, INCLUDING RINGS, CHAINS AND PINS BEFORE COMMENCING
EXERCISE.
9. ALWAYS WEAR SUITABLE CLOTHING AND FOOTWEAR DURING EXERCISE. DO NOT
WEAR LOOSE FITTING CLOTHING THAT COULD BECOME ENTANGLED WITH THE
MOVING PARTS OF YOUR EXERCISE MACHINE.
10. WARM UP 5 TO 10 MINUTES BEFORE EACH WORKOUT AND COOL DOWN 5 TO 10
MINUTES AFTERWARD. THIS ALLOWS YOUR HEART RATE TO GRADUALLY INCREASE
AND DECREASE AND WILL HELP PREVENT STRAINING MUSCLES.
11. NEVER HOLD YOUR BREATH WHILE EXERCISING. BREATHING SHOULD REMAIN AT A
NORMAL RATE IN CONJUNCTION WITH THE LEVEL OF EXERCISE BEING PERFORMED.
12. REST ADEQUATELY BETWEEN WORKOUTS. MUSCLES TONE AND DEVELOP DURING
THESE REST PERIODS. BEGINNERS SHOULD WORK OUT TWICE A WEEK AND
INCREASE GRADUALLY TO 4 OR 5 TIMES PER WEEK.
13. DO NOT "OVER TRAIN". INCORRECT OR EXCESSIVE TRAINING MAY RESULT IN INJURY.
- 1 -
WARNING : BEFORE COMMENCING WITH ANY EXERCISE PROGRAM, PLEASE CONSULT
YOUR FAMILY PHYSICIAN. IF AT ANY TIME DURING EXERCISE YOU FEEL FAINT,
DIZZY OR EXPERIENCE PAIN, STOP AND CONSULT YOUR FAMILY PHYSICIAN.
IN THE EVENT ANY OF THE ABOVE MENTIONED WARNINGS ARE BREACHED
BY THE CONSUMER, THE MANUFACTURER MAY USE SAME AS A DEFENSE TO
ANY CLAIM FOR INJURIES, DAMAGE OR LOSS. THE ABOVE WARNINGS ARE IN
NO WAY INTENDED TO LIMIT OR MODIFY THE CONSUMER'S REMEDIES FOR
BREACH OF WARRANTIES PURSUANT TO APPLICABLE FEDERAL AND STATE
LAWS OF REGULATIONS. THEY ARE BEING SUPPLIED STRICTLY TO ENSURE
THE SAFETY OF THE INDIVIDUALS USING THIS PRODUCT.
THE APPLIANCES ARE NOT FOR CHILDREN UNDER 14 YEARS OF AGES.
BEFORE YOU BEGIN
IMPORTANT : READ ALL INSTRUCTIONS CAREFULLY. ASSEMBLE THE UNIT IN
ACCORDANCE WITH THE STEPS IN THE MANUAL. LAY OUT ALL PARTS ON
THE FLOOR AND CHECK IF YOU HAVE ALL THE PARTS INCLUDED
COMPLETELY BEFORE BEGINNING ASSEMBLY. IN CASE OF A DISCREPANCY,
PLEASE CALL THE CUSTOMER SERVICE DEPARTMENT OF THE STORE FOR
HELP.
NOTE : SOME PARTS MAY BE FACTORY PRE-ASSEMBLED.
TOOLS REQUIRED FOR ASSEMBLY
ONE ADJUSTABLE WRENCH, A PHILIPS HEAD SCREWDRIVER AND A ALLEN KEY
THE SAFETY LEVEL OF THE EQUIPMENT CAN BE MAINTAINED ONLY IF IT IS
EXAMINED REGULARLY FOR DAMAGED AND WEAR.
THE PEDAL CRANK TRAINING EQUIPMENT OF CLASS B AND C IS NOT
SUITABLE FOR THERAPEUTIC PURPOSES.
REPLACED DEFECTIVE COMPONENTS IMMEDIATELY AND KEEP THE
EQUIPMENT OUT OF USE UNTIL REPAIR.
THE MOST SUSCEPTIBLE TO WEAR PARTS ARE
DRUM MAGNETIC WHEEL
BELT
B.B PARTS
- 2 -
- 1 -
NOTE : THE EQUIPMENT IS SPEED-DEPENDENT ON BRAKING SYSTEM.
IMPORTANT : THE MAXIMUM RECOMMENDED WEIGHT CAPACITY FOR
YOUR EQUIPMENT IS 110 KG ( 240 LB ) PER USER.
IMPORTANT
READ ALL STEPS BEFORE ATTACHING PEDALS.
PEC-2035 SERIES / PEC-2055 / PEC-2075
HOME MAGNETIC CYCLE ASSEMBLY INSTRUCTION
- 3 -
STEP 1. ATTACH BOTH FRONT AND REAR STABILIZERS ( 02 / 03 ) TO MAIN FRAME ( 01 ) ,
FIX WITH CARRIAGE BOLTS ( 27 ) WASHERS ( 31 ) AND DOME NUTS ( 35 ).
STEP 2. a. ATTACH PEDALS ( 18 / 19 ) TO PEDAL CRANKS , ( PEDALS MARKED " L "
AND " R " INDICATES LEFT AND RIGHT SIDE OF BIKE. MAKE SURENOT TO
MIX ITS UP ).
b. LEFT PEDAL HAS LEFTHAND THREAD AND MUST BE TURNED
COUNTERCLOCKWIDE ( CCW ) TO ATTACH. RIGHT PEDAL HAS RIGHTHAND
THREAD , MUST BE TURNED CLOCKWISE ( CW ) TO ATTACH.
STEP 3. ATTACH SADDLE ( 13 ) TO SADDLE PLATE OF SEAT POST ( 04 ). FASTERN
WITH SPRING WASHERS ( 33 ) AND NYLON NUTS ( 34 ).
STEP 4. RELEASE KNOB ( 26 ) FROM SEAT POST SUPPORT ( ON MAIN FRAME ) SLIDE
SEAT POST INTO THE SEAT POST BOOT ( 14 ) THEN ATTACH SEAT POST ( 04 )
TO SEAT POST SUPPORT ( ON MAIN FRAME ) , ADJUST SADDEL TO DESIRE
HEIGHT AND TIGHTEN WITH KNOB ( 26 ).
ASSEMBLE HANDLEBAR POST
IF YOUR MODEL NO. IS PEC-2035/2035EP/2035GP/2075 PLEASE DO STEP 5.
IF YOUR MODEL NO. IS PEC-2055 PLEASE DO STEP 6.
STEP 5. a. RELEASE THE SCREW ( 29 ) FROM THE PARTS OF TENSION CONTROL ( 09 ).
b. INSERT TENSION CABLE ( 10 ) INTO HANDLEBAR POST ( 05 ) , PULL THE
TENSION CABLE OUT FROM MIDDLE HOLE OF HANDLEBAR POST ( 05 ).
c. CONNECT WIRE (A)( 11 ) AND WIRE (B)( 12 ) , THEN ATTACH HANDLEBAR
POST TO MAIN FRAME ( 01 ), FIX WITH BOLTS ( 28 ) AND WASHERS ( 31 ).
d. ASSEMBLE TENSION CONTROL ( 09 ) AND TENSION CABLE ( 10 ) , BY
CONNECTING CABLE HEAD ( ON KNOB ) TO THE DRAW HOOK OF
TENSION CABLE.
e. ASSEMBLE THE TENSION CONTROL ( 09 ) ONTO HANDLEBAR POST( 05 ).
NOTE THE FIX HOOK ( ON TENSION CONTROL ) WELL INSERTED ONTO
HANDLEBAR POST. THEN TIGHTEN WITH SCREW ( 29 ).
STEP 6. CONNECT WIRE (A)( 11 ) AND WIRE (B)( 12 ) MONITOR CABLE (A)( 40 ) AND
MONITOR CABLE (B)( 41 ) ( PLEASE REFER TO FIG. F ) THEN ATTACH
HANDLEBAR POST TO MAIN FRAME ( 01 ) FIX WITH BOLTS ( 28 ) AND
WASHERS ( 31 )
ASSEMBLE HANDLEBAR & MONITOR
IF YOUR MODEL NO IS PEC-2035/2035EP PLEASE DO STEP 7.
IF YOUR MODEL NO IS PEC-2035GP/2055/2075 PLEASE DO STEP 8.
( PLEASE REFER TO FIG. A & FIG. B )
STEP 7. a. ASSEMBLE HANDLEBAR ( 06 ) ONTO HANDLEBAR POST ( 05 ) FASTEN THE
T-KNOB ( 25 ) WITH M8 SMALL WASHER ( 32 ) ON IT ( 05 )
ASSEMBLE FOAM GRIP ( 17 ) AND HANDLEBAR END CAP ( 16 )
NOTE USE SOME SOAP WATER AS LUBRICANT WHILE FITTING FOAM GRIP.
b. CONNECTING WIRE (A)( 11 ) WITH MONITOR ( 08 ) THEN SLIDE THE
MONITOR INTO MOUNTING PLATE CAREFULLY
STEP 8. a. ATTACH HALF MOON BRACKET ( 39 ) HANDLEBAR ( 06 ) TO HANDLEBAR
POST ( 05 ) AND FIX WITH SCREW ( 38 ) T-KNOB ( 25 ) & WASHER ( 32 )
DO NOT OVERTIGHTEN THE SCREW & T-KNOB BEFORE THE HANDLEBAR
LOCATED IN DESIRED POSITION ( PLEASE REFER TO FIG. C )
( NOTE TO ADJUST ANGLE OF HANDLEBAR BY UN SCREWINGT KNOB
THEN TIGHTEN IT FIRMLY )
b. INSERT THE GRIP PULSE WIRE ( 36 ) INTO THE HANDLEBAR POST AND LET
IT THROUGH THE TOP OF MONITOR MOUNTING PLATE
c. CONNECTING WIRE (A)( 11 ) & GRIP PULSE WIRE ( 36 ) WITH MONITOR ( 08 ).
( PLEASE REFER TO FIG. D )
IF YOUR MODEL NO IS PEC - 2055 PLEASE DO d.
d. CONNECTING WIRE (A)( 11 ) & GRIP PULSE WIRE ( 36 ) & MONITOR CABLE
(A)( 40 ) WITH MONITOR ( 08 ) ( PLEASE REFER TO FIG. E )
e. SLIDE THE MONITOR INTO MOUNTING PLATE CAREFULLY
MANUFACTURER SERVICE
PROTEUS SPORTS INC.
"FOR CUSTOMER SERVICE
PLEASE CONTACT THE SALES
OUTLET, WHERE YOU PURCHASED
THIS EQUIPMENT, FOR CUSTOMER SERVICE"
CORRECT POSTURE FOR PEC-2035 SERIES
- 4 -
- 5 -
EXPLODED VIEW
FIG. C PEC-2035GP
PEC-2055GP
PEC-2075
ALLEN
KEY
38
36
6
39
32
25
5
FIG. D PEC-2035GP
PEC-2075
6
30
37
11
8
36
FIG. E PEC-2055GP
6
11
8
37
36
30
40
PEC-2035/2035EP
FIG. B
9
10
FIG. F
11
12
41
40
FIG. A
10
9
18
27
23
1
20
7
24
27
3
31
35
2
31
31
35
21
22
12
11
14
19
32
25
6
29
5
10
9
33
34
4
17
16
8
11
13
28
15
26
KEY Q'TY DESCRIPTION
1. 1 MAIN FRAME
2. 1 FRONT STABILIZER
3. 1 REAR STABILIZER
4. 1 SEAT POST
5. 1 HANDLEBAR POST
6. 1 HANDLEBAR
7. 1 CRANK ASSEMBLY
8. 1 CYCLE MONITOR
9. 1 TENSION CONTROL
10. 1 TENSION CABLE
11. 1 WIRE (A)
12. 1 WIRE (B)
13. 1 SADDLE
14. 1 SEAT POST BOOT
15. 1 30 x 60 SLEEVE
16. 2 HANDLEBAR END CAP
17. 2 FOAM GRIP
18. 1 PEDAL (R)
19. 1 PEDAL (L)
20. 2 CRANK HOLE COVER
21. 1 CHAIN COVER (R) W / ORNATE PLATE
22. 1 CHAIN COVER (L) W / ORNATE PLATE
23. 2 FOOT CAP (A)
24. 2 FOOT CAP (B)
25. 1 T - KNOB
26. 1 KNOB
27. 4 M8 CARRIAGE BOLT x 70 mm
28. 3 M8 SOCKET BOLT x 15 mm
29. 1 M5 SCREW x 25 mm
30. 4 M4 SCREW
31. 7 M8 WASHER
32. 1 M8 SMALL WASHER
33. 3 M8 SPRING WASHER
34. 3 M8 NYLON NUT
35. 4 M8 DOME NUT
36. 1 GRIP PULSE WIRE
37. 2 GRIP PULSE
38. 1 M7 SCOKET SCREW x 20 mm
39. 1 HALF MOON BRACKET
40. 1 MONITOR CABLE (A)
41. 1 MONITOR CABLE (B)
PARTS LIST
- 6 -
GB
PEC2035SERIES-030317GB
/
