Revision: 1.1
AR-R6000D41 & AR-R6000D51
System Guide
1
Revision: 1.1
Contents
1. ................4 Introduction to AR-R6000D41 & AR-R6000D51
1.1 ...............................................................................4 Specifications
1.2
..................................................................................4 Packing List
1.3
........................................................................5 System Dissection
2. ...............................7 Procedure of Assembly/Disassembly
2.1. ...........7 Installing the 2.5”Hard Disk Drive (HDD) and CF card
2.2.
.................................. 11 Installing mini PCI Card and SO-DIMM
2.3.
.................................................12 Installing Extension PCI Card
3. .....................................................14 AR-B6000 Board Guide
3.1. ..............................................................................14 Introduction
3.1.1. ...............................................................................................14 Features
3.1.2.
........................................................................................15 Specification
3.1.3.
...............................................................................16 Package Contents
3.1.4.
.....................................................................................17 Block Diagram
3.2. ..............................................................18 Hardware Information
3.2.1. ...............................................................................................18 Location
3.2.1.1. ...........................................................................................................18 Top Side
3.2.1.2. .....................................................................................................19 Bottom Side
3.2.2. ..................................20 Connector, Header and Jumper Setting Table
3.2.2.1. ...........................................................................21 Pin definition for Connector
3.2.2.2. ................................................................................22 Pin definition for Header
3.2.2.3. .................................................................23 Jumper Setting and Pin definition
3.3. .............................................................................24 BIOS Setting
3.3.1. .....................................................................24 Main (System Overview)
3.3.2.
.........................................................24 Advanced (Advanced Settings)
2
Revision: 1.1
3.3.3. ..........................................................................25 Power (ACPI Setting)
3.3.4.
...........................................................................25 Boot (Boot Settings)
3.3.5.
...............................................................................26 Exit (Exit Options)
3.4. ...................................................................................27 Appendix
3.4.1. .............................................27 Appendix A - RJ45 LAN LED definition
3.4.2.
...................................28 Appendix B- Front Panel LAN LED definition
3.4.3.
...........................................29 Appendix C- Front Panel LED definition
3.4.4.
.........................................................29 Appendix D- AR-LCM definition
3.4.5.
........................................................30 Appendix E- AR-LCM Demo API
3
Revision: 1.1
1. Introduction to AR-R6000D41 & AR-R6000D51
Acrosser's Rackmount Networking device AR-R6000 is a cost-effective and entry-level solution,
which is suitable for small office. Base on Intel ATOM D410 (single core & 512K cache) or D510
(dual cores & 1M cache) 1.66GHz CPU, the AR-R6000 consumes very low power to save the total
costs. We also put a quiet fan to keep the low noise, which will not cause uncomfortable voice. By
four 10/100/1000Mbps LANs, the AR-R6000 is sufficient for the small business security hardware
solution.
Key features:
1. Intel ATOM D410 or D510 CPU
2. Intel ICH8M Chipsets.
3. DDRII 667/800 SO-DIMM x 1, up to 2GB memory
4. Intel 82574L 10/100/1000Mbps x 4
5. For R6000D51 system, LAN1 and LAN2 support bypass feature
6. CF socket, 2.5”/3.5” HDD bay x 1, SATA II interface with power x 2
7. Console, VGA (pinhead), USB 2.0 x 4 (2 x connectors, 2 x pin head)
8. Support boot from LAN, console redirection
9. Support mini-PCI and PCI card for feature expansion
10. With LCM module, users can easily program R6000 system
1.1 Specifications
Item Description
System AR-R6000D41 & AR-R6000D51
CPU Board AR-B6000D41 & AR-B6000D51
System Dimensions 442.4×340.5×44 (mm)
1.2 Packing List
Description Q’ty
AR-R6000D41 & AR-R6000D51 1
Console Cable 1
Quick user manual 1
CD with Driver and Manual 1
HDD bracket 2
SATA cable 1
SATA power cable 1
Rack bracket 2
Rubber for HDD bracket 4
4
Revision: 1.1
1.3 System Dissection
(1) Dimensions
(2) Front Panel
5
LCM Module Window
LCM Keypad
Revision: 1.1
(3) System Configuration
Item Part No. Description Remark
1 170010963-G TOP COVER 1
2 170010962-G BOTTOM 1
3 170010964-G BOTTOM BRACKET 1
4 170010965-G & 170010966-G HDD BRACKET(FOR 2.5” & 3.5”) 1
5 020010024 OR 020010025 AR-B6000D41 OR AR-B6000D51 1
6 010080650 AR-RS18 1
7 - PCI CARD 1
8 150010098-G POWER 1
9 140060026-G FAN 2
10 150010098-G POWER SWITCH 1
11 150010098-G POWER CORE 1
12 180070084-G
銘板
1
13 010020235-03 LCM Module 1
14 170010967-G Mounting Bracket 2
6
Revision: 1.1
2. Procedure of Assembly/Disassembly
2.1. Installing the 2.5”Hard Disk Drive (HDD) and CF card
The following are step-by-step installation
1. Remove the power cord out from the AR-R6000
2. Unscrew the two screws to release top cover of AR-R6000, as shown in Fig-01.
Push(Open) Push(Open)
Unscrew
Unscrew
Fig- 01
Remove the top cover
3. Install HDD into HDD bracket and lock HDD body and bracket by screws (3.5”HDD : 6pcs ,
2.5”HDD : 4pcs), as shown in Fig-02-1 & Fig-02-2
Fig-02-1 HDD bracket with HDD body Fig-02-2 HDD bracket with HDD body
7
Revision: 1.1
4. Paste rubbers on the HDD bracket, as shown in Fig-02-3.
plaser the rubbers on the HDD bracket.
Fig-0
2-3 paste the rubbers with HDD bracket
5. Connect SATA cable to HDD module (HDD+HDD bracket) , as Fig-03.
Fig-03 connect SATA cable to HDD module
8
Revision: 1.1
6. Place HDD module back to the case and lock HDD module to the chassis by four screws as
Fig-04-1,04-2 and connect SATA cable to mainboard, as Fig-04-3.
Fig-04-1 Fig-04-2
9
F
ig-04-3 Install SATA power cable and SATA cable
Revision: 1.1
7. Installing CF card as shown in Fig-05
The direction for
installing the CF card
Fig-06 The direction for installing the CF card
8. Lock top cover of AR-R6000 by two screws, as shown in Fig-06.
Fig-06 Lock the top cover
Push(Close) Push (Close)
Locked up Locked up
10
Revision: 1.1
2.2. Installing mini PCI Card and SO-DIMM
The following are step-by-step installation
1. Take off the bottom_bracket by removing the 2 screws, as shown in Fig-07
Fig-07-1 Remove the extending doors by removing the 2 screws.
Unscrew
The direction for installing the
Mini-PCIE card installs for
The direction for installing the SO-DIMM
Fig-0
7-2 Install the cards in the chassis
11
Revision: 1.1
2.3. Installing Extension PCI Card
The following are instructions for PCI card installation.
1. AR-R6000 can be extended with a PCI card.
2. Unscrew the two screws to release top cover of AR-R6000, as Fig-01.
3. Release the dummy bracket by unscrewing the screws as shown in Fig-08.
Fig-08. unlock the screws for PCI card
Unlocked the screws
4. Takes off PCI bracket, then assembles the PCI card and PCI bracket as shown in Fig-09.
Fig-09-1 Unlock the bracket
unlock
12
Revision: 1.1
Lock up
Fig-09-2 Lock PCI card
5. Plug the extension PCI card into riser card and adjust the card into the holder as shown in
Fig-10.
1.)Plug in the PCI card
2.)Locked the screws
Fig-10 Install the PCI card
13
Revision: 1.1
14
3. AR-B6000 Board Guide
3.1. Introduction
Welcome to the AR-B6000 series Computer. The AR-B6000 series is a Networking board for
Micro-box and Rack-mount with four sets of GbE LAN. Intel Atom (Pineview-D) D410/D510
+ICH8M.
AR-B6000D41 is a networking board for micro-box and Rack-mount Platform with Intel Atom
D410 +ICH8M, 4*10/100/1000 LAN.
AR-B6000D51 is a Networking board for micro-box and Rack-mount Platform with Intel Atom
D510 +ICH8M, 4*10/100/1000 LAN with by-pass.
3.1.1. Features
Processor:
AR-B6000D41: Intel® Atom™ Processor D410 (Single Core, 512K L2 Cache, 1.66 GHz)
AR-B6000D51: Intel® Atom™ Processor D510 (Dual Core, 2X 512K L2 Cache, 1.66 GHz)
Chipsets: Intel® ICH8M
Memory: DDR2 667/800MHz SO-DIMM, Maximum 2GB
Display: VGA
Storage: 1x CF, 2x SATA II,
Communication: 4x Gbps Ethernet, 7x USB 2.0, 3x RS-232, 1x RS-232/422/485
General: Watchdog timer, 8-bit GPIO, and PCI-104 expansion slot.
Revision: 1.1
3.1.2. Specification
System
CPU AR-B6000D41 Intel® Atom™ Processor D410 (512K L2 Cache, 1.66 GHz)
AR-B6000D51 Intel® Atom™ Processor D510 (2X 512K L2 Cache, 1.66 GHz)
Memory One SO-DIMM socket support 667/800 MHz DDR2 SDRAM up to 2GB
Graphic
Controller
Intel® GMA 3150
Gen3.5+ GFX Core, GFX Render Core Frequency @ 200MHz (400MHz), DX9
Video Memory DVMT 4.0, Maximum 256MB shared
Intel® Dynamic Video Memory Technology support 4.0
Video Interface 1 x VGA port (DB15)
Chipset Intel® ICH8M
Thermal
solution
FAN connector for CPU FAN
Fan connector for system FAN*2
BIOS 1. support console redirection(default enable)
2. support bypass setting(default disable)
3. support boot from LAN
Super I/O W83627DHC
Network Interface
Ethernet 4 *RJ45 JACK with LED (Refer to Appendix A)
Intel 82574L (10/100/1000Mbps) (L1~L4),
LAN by-Pass LAN1 and LAN2 support by-pass function
Reserve 1*3 pin Jumper for Hardware select bypass status.
AR-B6000D51 only
I/O
Front panel From left to right:
1. LAN1/ LAN2/ LAN3/ LAN4 LED: 1000, 10/100, Act. (Refer to Appendix B)
2. Power LED/HDD/Bypass: Green/Green/Yellow (Refer to Appendix C)
Rear panel From left to right:
Power Inlet
2 * USB (use standby power)
COM port (DB9)
LAN4/ LAN3/ LAN2
Reset Button
LAN1
Internal I/O
1. 4 x USB 2.0(2.54 pitch)
Mini-PCI
PCI slot
GPIO:
Use super I/O game port as GPIO
2x5 pin 2.0mm Pin Head
8-bit GPIO, 1 x GND, 1 x 3.3V/5V jumper selectable
LCM pin head( 7-pin pinhead 2.54mm)
Power input (Mini Fit 4 pin Co-lay with power inlet)
1*8 pin 2.54mm reserve for CPLD update
VGA pin head(2*5pin, 2.0mm
Panel connector(2*4pin, 2.54mm)
Storage
15
Revision: 1.1
16
CF 1 x Compact Flash socket, Type-II Socket
(Master mode) Support UDMA
SATA 2 x SATAII interface with power(JST 4 pin)
Others
Watchdog Timer Software programmable 1~255 Seconds,
Battery Lithium Battery, 3V 220mAH (CR2032)
Hardware
monitoring
CPU voltage
CPU and System Temperature
OS support Win XP/XP Embedded, Fedora 10(2.6.27)
Mechanical
Dimension 218 x 146mm
Operating
Temperature
0~60°C (32~140°F)
Storage
Temperature
-20~80°C (-4~176°F)
Relative
Humidity
0 to 90% @ 40°C, non-condensing (95% @ 40°C, Non-Condensing by request)
Power Supply N/A
Power
Requirements
12V Single Voltage Input
ATX circuit as AT mode
EMC & Safety
EMC CE, FCC Class B
Safety N/A
3.1.3. Package Contents
Model Name Part Lists QTY Remark
AR-B6000 series 1
AR-B6000
series
Revision: 1.1
3.1.4. Block Diagram
17
Revision: 1.1
3.2. Hardware Information
This chapter describes the installation of AR-B6000. At first, it shows the Function diagram and
the layout of AR-B6000. It then describes the unpacking information that you should read carefully,
as well as the jumper/switch settings for the AR-B6000 configuration.
3.2.1. Location
3.2.1.1. Top Side
18
Revision: 1.1
3.2.1.2. Bottom Side
19
Revision: 1.0
3.2.2. Connector, Header and Jumper Setting Table
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
