Hikoki C 10FCH Owner's manual

Compound Miter Saw

Kapp-und Gehrungssäge

Scie à onglets

Sega circolare orientabile

Afkort en paneelzaagmachine

Ingletadora

Serra de esquadria

º·ÏÙÛÔÎﬁÙË˜ ÌÂ Û·ÛÙ‹ ÎÂÊ·Ï‹

C 12LCH

•

C 12LC

•

C 12FCH

Handling instructions

Bedienungsanleitung

Mode d’emploi

Instruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

δηγίες ειρισµύ

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste instruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer cuidadosamente y comprender estas instrucciones antes del uso.

Antes de usar, leia com cuidado para assimilar estas instruções.

∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.

001Cover_C12LCH_WE 3/11/09, 18:481

Page is loading ...

6

English Deutsch Français

1 Handle Griff Poignée

2 Lock lever (D) Sperrhebel (D) Levier de verrouillage (D)

3 Motor Head Motorkopf Tête de moteur

4 Gear Case Getriebegehäuse Réducteur

5 Dust Bag Staubbeutel

Bacquet de réception des copeaux

6

Laser Marker Lasermarkierer Marqueur à laser

(Only C12LCH/C12FCH) (Nur C12LCH/C12FCH) (C12LCH/C12FCH seulement)

7 Vise Assembly Schraubstocksatz Ensemble d’étau

8 Fence (B) Gitter (B) Guide (B)

9 Sub Fence Hilfsführung Guide auxiliaire

0 Turntable Drehbühne Plaque tournante

A Indicator (A) (For miter scale) Zeiger (A) (Für Gehrungsskala)

Indicateur (A) (Pour l'échelle d'onglet)

B Side Handle Seitengriff Poignée latérale

C Lever Hebel Levier

D

Digital Display Digitalanzeige Affichage numérique

(Only C12LCH/C12LC) (nur C12LCH/C12LC) (C12LCH/C12LC seulement)

E Table Insert Tischeinsatz Plaque d’insertion

F Fence (A) Gitter (A) Guide (A)

G Lower Guard Unterer Schutz Guide inférieur

H Saw Blade Sägeblatt Lame de scie

I Motor Motor Moteur

J Nameplate Typenschild Plaque signalétique

K Trigger Switch Auslöserschalter Interrupteur à détente

L

Switch (For laser marker) Schalter (Für Lasermarkierer) Interrupteur (Pour marqueur à laser)

(Only C12LCH/C12FCH) (Nur C12LCH/C12FCH) (C12LCH/C12FCH seulement)

Switch (For Digital Display) Schalter (für Digitalanzeige)

Interrupteur

M

(Only C12LCH/C12LC) (nur C12LCH/C12LC)

(pour Affichage numérique)

(C12LCH/C12LC seulement)

N Base Grundplatte Socle

O Knob (A) Knopf (A) Bouton (A)

P Holder (B) Halter (B) Support (B)

Q Clamp Lever Klemmhebel Levier de serrage

R Locking Pin Verriegelungsstift Goupille de verrouillage

S 17 mm Box Wrench 17 mm Steckschüssel Clé à écrous de 17 mm

T 4 mm Hex. Bar Wrench 4 mm-Sechskantschlüssel Clé à tige hexagonale de 4 mm

U Duct Kanal Conduit

V Right Angle Rechter Winkel Angle droit

W Link (C) Verbindungsstück (C) Lien (C)

X 6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

Y Line Linie Ligne

Z Warning Sign Warnsymbol Signe d’avertissement

[ 6 mm Bolt 6 mm-Schraube Boulon 6 mm

\ Screw Holder Schraubenhalter Support de vis

] 6 mm Wing Bolt (B) 6 mm-Flügelschraub (B) Boulon à ailettes de 6 mm (B)

` Vise Shaft Schraubstockachse Arbre de l’étau

a 6 mm Wing Bolt (A) 6 mm-Flügelschraub (A) Boulon à ailettes de 6 mm (A)

b Workpiece Werkstück Pièce

c Vise Plate Schraubstockbacke Talon

d Knob Knopf Bouton

002Table_C12LCH_WE 3/11/09, 18:496

7

English Deutsch Français

e Laser line Laserlinie Raie laser

f Groove Nut Rainure

g Marking (pre-marked) Markierung (vor-gekennzeichnet) Marquage (pré-marqué)

h Miter angle window Gehrungswinkelanzeige Fenêtre d’angle d’onglet

i Miter angle reset button Gehrungswinkel-Rückstelltaste

Touche de réinitialisation de

l’angle d’onglet

j Back light ON/OFF Hintergrundbeleuchtung EIN/AUS Eclairage de fond ON/OFF

k Bevel angle reset button

Schrägschnittwinkel-Rückstelltaste

Touche de réinitialisation de

l’angle de biseau

l Bevel angle window Schrägschnittwinkelanzeige Fenêtre d’angle de biseau

m Miter Scale Gehrungsskala Echelle d'onglet

n

Indicator (B) Anzeiger (B) Indicateur (B)

(For bevel scale) (Für Schrägschnittsskala) (pour échelle de biseau)

o Plate (B) Platte (B) Plaque (B)

p Plate (A) Platte (A) Plaque (A)

q Holder (Optional accessory) Halter (Sonderzubehör) Support (Accessoire en option)

r Steel Square Stahlwinkel Equerre en acier

s

6 mm Wing Nut (Optional accessory)

Flügelschraube, 6 mm Ecrou à ailettes de 6 mm

(Sonderzubehör) (Accessoire en option)

t

Height Adjustment Bolt 6 mm Höheneinstellschraube, 6 mm Boulon de réglage de la hauteur

(Optional accessory) (Sonderzubehör) de 6 mm (Accessoire en option)

u Base Surface Grundfläche Surface du socle

v

6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

(Optional accessory) (Sonderzubehör) (Accessoire en option)

w Stopper (Optional accessory) Anschlag (Sonderzubehör) Butée (Accessoire en option)

x

6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

(Optional accessory) (Sonderzubehör) (Accessoire en option)

y 6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

Crown Molding Vise Ass’y Schraubstocksatz für

Ensemble d'étau de corniche à

z

(Optional accessory) Kronenform (Sonderzubehör)

courbe complexe

(Accessoire en option)

{ 6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

| 6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

}

Crown Molding Stopper (L) Kronenformanschlag (L) Butée de corniche à courbe

(Optional accessory) (Sonderzubehör) complexe (L) (Accessoire en option)

~

Crown Molding Stopper (R) Kronenformanschlag (R) Butée de corniche à courbe

(Optional accessory) (Sonderzubehör) complexe (R) (Accessoire en option)

å 6 mm Knob Bolt 6 mm-Knopfschraube Vis moletée de 6 mm

ç Knob Knopf Bouton

† Crown molding Kronenform Corniche à courbe complexe

¢ 5 mm Machine Screw 5 mm-Maschinenschraube Vis à métaux de 5 mm

£ Spindle Cover Spindelabdeckung Couvercle de l’arbre

§ Spindle Lock Spindelhebel Verrou en fuseau

• Bolt Schraube Boulon

¶ Washer (D) Unterlegscheibe (D) Rondelle (D)

ß Washer (C) Unterlegscheibe (C) Rondelle (C)

® Hex.Head Bolt Sechskantschraube Boulon à tête hexagonale

™ Groove for Driver Aussparung für Schraubendreher Rainure pour clé à écrous

¥ Brush Cap Bürstenkappe Bouchon de carbone

002Table_C12LCH_WE 3/11/09, 18:497

Page is loading ...

12

Symbols

WARNING

The following show symbols used

for the machine. Be sure that you

understand their meaning before

use.

Symbole

WARNUNG

Die folgenden Symbole werden für

diese Maschine verwendet. Achten

Sie darauf, diese vor der

Verwendung zu verstehen.

Symboles

AVERTISSEMENT

Les symboles suivants sont utilisés

pour l’outil. Bien se familiariser

avec leur signification avant

d’utiliser l’outil.

Simboli

AVVERTENZA

Di seguito mostriamo i simboli

usati per la macchina. Assicurarsi

di comprenderne il significato

prima dell’uso.

Read all safety warnings and all

instructions.

Failure to follow the warnings and

instructions may result in electric

shock, fire and/or serious injury.

Always wear eye

protection.

Lesen Sie sämtliche

Sicherheitshinweise und

Anweisungen durch.

Wenn die Warnungen und

Anweisungen nicht befolgt

werden, kann es zu Stromschlag,

Brand und/oder ernsthaften

Verletzungen kommen.

Lire tous les avertissements de

sécurité et toutes les instructions.

Tout manquement à observer ces

avertissements et instructions peut

engendrer des chocs électriques,

des incendies et/ou des blessures

graves.

Leggere tutti gli avvertimenti di

sicurezza e tutte le istruzioni.

La mancata osservanza degli

avvertimenti e delle istruzioni

potrebbe essere causa di scosse

elettriche, incendi e/o gravi lesioni.

Symbolen

WAARSCHUWING

Hieronder staan symbolen

afgebeeld die van toepassing zijn op

deze machine. U moet de betekenis

hiervan begrijpen voor gebruik.

Símbolos

ADVERTENCIA

A continuación se muestran los

símbolos usados para la máquina.

Asegúrese de comprender su

significado antes del uso.

Símbolos

AVISO

A seguir aparecem os símbolos

utilizados pela máquina. Assimile

bem seus significados antes do

uso.

Lees alle waarschuwingen en

instructies aandachtig door.

Nalating om de waarschuwingen

en instructies op te volgen kan in

een elektrische schok, brand en/of

ernstig letsel resulteren.

Draag altijd

oogbescherming.

Lea todas las instrucciones y

advertencias de seguridad.

Si no se siguen las advertencias e

instrucciones, podría producirse

una descarga eléctrica, un

incendio y/o daños graves.

Utilice siempre una

protección ocular.

Leia todas as instruções e avisos

de segurança.

Se não seguir todas as instruções

e os avisos, pode provocar um

choque eléctrico, incêndio e/ou

ferimentos graves.

Utilize sempre

protecção para os olhos.

Tragen Sie immer einen

Augenschutz.

Indossate sempre le

protezioni oculari.

Only for EU countries

Do not dispose of electric tools

together with household waste

material!

In observance of European

Directive 2002/96/EC on waste

electrical and electronic equipment

and its implementation in

accordance with national law,

electric tools that have reached the

end of their life must be collected

separately and returned to an

environmentally compatible

recycling facility.

Nur für EU-Länder

Werfen Sie Elektrowerkzeuge nicht

in den Hausmüll!

Gemäss Europäischer Richtlinie

2002/96/EG über Elektro- und

Elektronik- Altgeräte und

Umsetzung in nationales Recht

müssen verbrauchte

Elektrowerkzeuge getrennt

gesammelt und einer

umweltgerechten

Wiederververtung zugeführt

werden.

Pour les pays européens

uniquement

Ne pas jeter les appareils électriques

dans les ordures ménagères!

Conformément à la directive

européenne 2002/96/EG relative aux

déchets d’équipements électriques

ou électroniques (DEEE), et à sa

transposition dans la législation

nationale, les appareils électriques

doivent être collectés à part et être

soumis à un recyclage respectueux

de l’environnement.

Solo per Paesi UE

Non gettare le apparecchiature

elettriche tra i rifiuti domestici.

Secondo la Direttiva Europea

2002/96/CE sui rifiuti di

apparecchiature elettriche ed

elettroniche e la sua attuazione in

conformità alle norme nazionali, le

apparecchiature elettriche esauste

devono essere raccolte

separatamente, al fine di essere

reimpiegate in modo eco-

compatibile.

Alleen voor EU-landen

Geef elektrisch gereedschap niet

met het huisvuil mee!

Volgens de Europese richtlijn 2002/

96/EG inzake oude elektrische en

elektronische apparaten en de

toepassing daarvan binnen de

nationale wetgeving, dient

gebruikt elektrisch gereedschap

gescheiden te worden ingezameld

en te worden afgevoerd naar een

recycle bedrijf dat voldoet aan de

geldende milieu-eisen.

Sólo para países de la Unión

Europea

¡No deseche los aparatos eléctricos

junto con los residuos domésticos!

De conformidad con la Directiva

Europea 2002/96/CE sobre residuos

de aparatos eléctricos y electrónicos

y su aplicación de acuerdo con la

legislación nacional, las

herramientas eléctricas cuya vida

útil haya llegado a su fin se deberán

recoger por separado y trasladar a

una planta de reciclaje que cumpla

con las exigencias ecológicas.

Apenas para países da UE

Não deite ferramentas eléctricas

no lixo doméstico!

De acordo com a directiva

europeia 2002/96/CE sobre

ferramentas eléctricas e

electrónicas usadas e a

transposição para as leis

nacionais, as ferramentas

eléctricas usadas devem ser

recolhidas em separado e

encaminhadas a uma instalação de

reciclagem dos materiais

ecológica.

Toujours porter des

verres de protection.

Always wear hearing

protection.

Stets Gehörschutz

tragen.

Porter des protections

anti-bruit en permanence.

Indossare sempre i

dispositivi di protezione

acustica.

Draag altijd

gehoorbescherming.

Utilice siempre

protecciones auriculares.

Use sempre proteção

auditiva.

™‡Ì‚ÔÏ·

¶ƒ√™√Ã∏

Τα παρακάτω δείνυν τα σύµ>λα

πυ ρησιµπιύνται στ µηάνηµα.

Βε>αιωθείτε τι κατανείτε τη

σηµασίας τυς πριν τη ρήση.

¢È·‚¿˙ÂÙÂ ﬁÏÂ˜ ÙÈ˜

ÚÔÂÈ‰ÔÔÈ‹ÛÂÈ˜ ·ÛÊ·ÏÂ›·˜ Î·È

ﬁÏÂ˜ ÙÈ˜ Ô‰ËÁ›Â˜.

Η µη τήρηση των πρειδπιήσεων

και δηγιών µπρεί να πρκαλέσει

ηλεκτρπλη'ία, πυρκαγιά και/ή

σ>αρ τραυµατισµ.

Φράτε πάντα τν

κατάλληλ ε'πλισµ για

την πρστασία των µατιών.

Mvo για τις ώρες της EE

Mηv πετάτε τα ηλεκτρικά

εργαλεία στov κάδo oικιακώv

απoρριµµάτωv!

Σύµωvα µε τηv εuρωπαϊκή

oδηγία 2002/96/EK περί

ηλεκτρικώv και ηλεκτρovικώv

σuσκεuώv και τηv εvσωµάτωσή

της στo εθvικ δίκαιo, τα

ηλεκτρικά εργαλεία πρέπει vα

σuλλέγovται 'εωριστά και vα

επιστρέovται για αvακύκλωση

µε τρπo ιλικ πρoς τo

περι>άλλov.

Φράτε πάντα

πρστατευτικά ακής.

002Table_C12LCH_WE 3/11/09, 18:4912

13

English

GENERAL OPERATIONAL PRECAUTIONS

WARNING! When using electric tools, basic safety

precautions should always be followed to reduce the risk

of fire, electric shock and personal injury, including the

following.

Read all these instructions before operating this product

and save these instructions.

For safe operations:

1. Keep work area clean. Cluttered areas and benches

invite injuries.

2. Consider work area environment. Do not expose

power tools to rain. Do not use power tools in damp

or wet locations. Keep work area well lit.

Do not use power tools where there is risk to cause

fire or explosion.

3. Guard against electric shock. Avoid body contact

with earthed or grounded surfaces (e.g. pipes,

radiators, ranges, refrigerators).

4. Keep children and infirm persons away. Do not let

visitors touch the tool or extension cord. All visitors

should be kept away from work area.

5. Store idle tools. When not in use, tools should be

stored in a dry, high or locked up place, out of reach

of children and infirm persons.

6. Do not force the tool. It will do the job better and

safer at the rate for which it was intended.

7. Use the right tool. Do not force small tools or

attachments to do the job of a heavy duty tool. Do

not use tools for purposes not intended; for example,

do not use circular saw to cut tree limbs or logs.

8. Dress properly. Do not wear loose clothing or

jewelry, they can be caught in moving parts. Rubber

gloves and non-skid footwear are recommended

when working outdoors. Wear protecting hair

covering to contain long hair.

9. Use eye protection. Also use face or dust mask if

the cutting operation is dusty.

10. Connect dust extraction equipment.

Cutting operation by this compound miter saw may

produce considerable amount of dust from

extraction duct on fixed guard.

(Dust material: Wood or Aluminium)

If devices are provided for the connection of dust

extraction and collection facilities ensure these are

connected and properly used.

11. Do not abuse the cord. Never carry the tool by the

cord or yank it to disconnect it from the receptacle.

Keep the cord away from heat, oil and sharp edges.

12. Secure work. Use clamps or a vise to hold the work.

It is safer than using your hand and it frees both

hands to operate tool.

13. Do not overreach. Keep proper footing and balance

at all times.

14. Maintain tools with care. Keep cutting tools sharp

and clean for better and safer performance. Follow

instructions for lubrication and changing

accessories. Inspect tool cords periodically and if

damaged, have it repaired by authorized service

center. Inspect extension cords periodically and

replace, if damaged. Keep handles dry, clean, and

free from oil and grease.

15. Disconnect tools. When not in use, before servicing,

and when changing accessories such as blades, bits

and cutters.

16. Remove adjusting keys and wrenches. Form the

habit of checking to see that keys and adjusting

wrenches are removed from the tool before turning

it on.

17. Avoid unintentional starting. Do not carry a plugged-

in tool with a finger on the switch. Ensure switch is

off when plugging in.

18. Use outdoor extension leads. When tool is used

outdoors, use only extension cords intended for

outdoor use.

19. Stay alert. Watch what you are doing. Use common

sense. Do not operate tool when you are tired.

20. Check damaged parts. Before further use of the tool,

a guard or other part that is damaged should be

carefully checked to determine that it will operate

properly and perform its intended function. Check

for alignment of moving parts, free running of

moving parts, breakage of parts, mounting and any

other conditions that may affect its operation. A

guard or other part that is damaged should be

properly repaired or replaced by an authorized

service center unless otherwise indicated in this

handling instructions. Have defective switches

replaced by an authorized service center. Do not use

the tool if the switch does not turn it on and off.

21. Warning

The use of any accessory or attachment, other than

those recommended in this handling instructions,

may present a risk of personal injury.

22. Have your tool repaired by a qualified person.

This electric tool is in accordance with the relevant

safety requirements. Repairs should only be carried

out by qualified persons using original spare parts.

Otherwise this may result in considerable danger

to the user.

PRECAUTIONS ON USING COMPOUND MITER

SAW

1. Keep the floor area around the machine level. Well

maintained and free of loose materials e.g. chips

and cut-offs.

2. Provide adequate general or localized lighting.

3. Do not use power tools for applications other than

those specified in the handling instructions.

4. Repairing must be done only by authorized service

facility. Manufacturer is not responsible for any

damages and injuries due to the repair by the

unauthorized persons as well as the mishandling of

the tool.

5. To ensure the designed operational integrity of

power tools, do not remove installed covers or

screws.

6. Do not touch movable parts or accessories unless

the power source has been disconnected.

7. Use your tool at lower input than specified on the

nameplate; otherwise, the finish may be spoiled and

working efficiency reduced due to motor overload.

8. Do not wipe plastic parts with solvent. Solvents such

as gasoline, thinner, benzine, carbon tetrachloride,

alcohol, may damage and crack plastic parts. Do not

wipe them with such solvent. Clean plastic parts with

a soft cloth lightly dampened with soapy water.

9. Use only original HITACHI replacement parts.

10. This tool should only be disassembled for

replacement of carbon brushes.

11. The exploded assembly drawing on this handling

instructions should be used only for authorized

service facility.

12. Never cut ferrous metals or masonry.

13. Adequate general or localized lighting is provided.

Stock and finished workpieces are located close to

the operators normal working position.

14. Wear suitable personal protective equipment when

necessary, this could include:

Hearing protection to reduce the risk of induced

hearing loss.

Eye protection to reduce the risk of injuring an eye.

Respiratory protection to reduce the risk of

inhalation of harmful dust.

01Eng_C12LCH_WE 3/11/09, 18:4913

14

English

Gloves for handling saw blades (saw blades shall

be carried in a holder wherever practicable) and

rough material.

15. The operator is adequately trained in the use,

adjustment and operation of the machine.

16. Refrain from removing any cut-offs or other parts

of the workpiece from the cutting area whilst the

machine is running and the saw head is not in the

rest position.

17. Never use the compound miter saw with its lower

guard locked in the open position.

18. Ensure that the lower guard moves smoothly.

19. Do not use the saw without guards in position, in

good working order and properly maintained.

20. Use correctly sharpened saw blades. Observe the

maximum speed marked on the saw blade.

21. Do not use saw blades which are damaged or

deformed.

22. Do not use saw blades manufactured from high

speed steel.

23. Use only saw blades recommended by HITACHI.

Use of saw blade comply with EN847-1.

24. The saw blades should be from 290 mm to 305 mm

external diameter ranges.

25. Select the correct saw blade for the material to be

cut.

26. Never operate the compound miter saw with the

saw blade turned upward or to the side.

27. Ensure that the workpiece is free of foreign matter

such as nails.

28. Replace the table insert when worn.

29. Do not use the saw to cut other than aluminium,

wood or similar materials.

30. Do not use the saw to cut other materials than those

recommended by the manufacturer.

31. Blade replacement procedure, including the method

for repositioning and a warning that this must be

carried out correctly.

32. Connect the compound miter saw to a dust

collecting device when sawing wood.

33. Take care when slotting.

34. When transporting or carrying the tool, do not grasp

the holder. Grasp the handle instead of the holder.

35. Start cutting only after motor revolution reaches

maximum speed.

36. Promptly cut OFF the switch when abnormality

observed.

37. Shut off power and wait for saw blade to stop before

servicing or adjusting tool.

38. During a miter or bevel cut the blade should not be

lifted until it has stopped rotation completely.

39. Take all the possibility of residual risks in cutting

operation into your consideration, such as the laser

radiation to your eyes, the inadvertent access to

moving parts on slide mechanical parts on machine

and so on.

SPECIFICATIONS

* Be sure to check the nameplate on product as it is subject to change by areas.

61.5 mm × 200 mm

0° or

96 mm × 155 mm

Miter 45° 61.5 mm × 140 mm

Bevel Left 45° 40 mm × 200 mm

Compound (Bevel Left 45°, Miter 45°)

40 mm × 140 mm

Saw Blade Dimensions (oD × iD × Thickness) 305 mm × 30 mm × 2.3 mm

Miter Cutting Angle Right and Left 0° – 52°

Bevel Cutting Angle Left –3° – 48°

Compound Cutting Angle

Miter (Right and Left) 0° – 45°

Bevel (Left) 0° – 45°

Voltage (by areas)* (110 V, 230 V)

Power Input* 1520 W

No-Load Speed 4000 min

–1

Machine Dimensions (Width × Depth × Height) 625 mm × 775 mm × 610 mm

Model C12LCH C12LC C12FCH

Weight (Net) 19.5 kg 19 kg

Digital Display Precision ±0.5° Yes Yes No

Laser Marker Yes No Yes

Maximum output Po<3 mW Class Laser Product

(Lambda) 654 nm

Laser medium Laser Diode

Max. Cutting

Capacity

Height × Width

01Eng_C12LCH_WE 3/11/09, 18:4914

15

English

STANDARD ACCESSORIES

(1) 305 mm TCT Saw blade (mounted on tool) ............. 1

(2) Dust bag ...................................................................... 1

(3) 17 mm Box wrench .................................................... 1

(4) Vise Assembly ............................................................ 1

(5) 4 mm Hex.bar wrench (only C12LCH/C12FCH) ........ 1

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (SOLD SEPARATELY)

(1) Extension Holder and Stopper

(2) Crown molding Vise Ass'y (Include Crown molding

Stopper (L))

(3) Crown molding Stopper (L)

(4) Crown molding Stopper (R)

Optional accessories are subject to change without notice.

APPLICATION

䡬 Cutting various types of aluminium sash and wood.

UNPACKING

䡬 Carefully unpack the power tool and all related items

(standard accessories).

䡬 Check carefully to make certain all related items

(standard accessories) are present.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the trigger

switch is in the ON position, the power tool will start

operating immediately, inviting serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be kept

as short as practicable.

4. When the power tool is prepared for shipping, its

main parts are secured by a locking pin

Move the handle slightly so that the locking pin can

be disengaged.

CAUTION

䡬 Set for transport

Lock the locking pin into the gear case (Fig. 3).

Remove a 6 mm wing bolt.Turn the link (C) as the Fig.

5, and fix it again with the 6 mm wing bolt.

Lower guard cover the teeth of the blade to the front

of the machine.

䡬 Cutting work

Move the handle slightly so that the locking pin can

be disengaged.

Remove a 6 mm wing bolt.Turn the link (C) as Fig. 6,

and fix it again with the 6 mm wing bolt.

5. Attach the dust bag to the main unit (Fig. 1)

(1) When the dust bag has become full of sawdust, dust will

be blown out of the dust bag when the saw blade rotates.

Check the dust bag periodically and empty it before it

becomes full.

(2) During bevel and compound cutting, attach the dust bag

at a right angle to the base surface as shown in Fig. 4.

CAUTION

䡬 Empty the dust bag frequently to prevent the duct and

the safety cover from becoming clogged.

Sawdust will accumulate more quickly than normal

during bevel cutting.

6. Installation

Ensure that the machine is always fixed to bench.

Attach the power tool to a level, horizontal work bench.

Select 8 mm diameter bolts suitable in length for the

thickness of the work bench.

Bolt length should be at least 35 mm plus the thickness

of the work bench.

For example, use 8 mm × 60 mm bolts for a 25 mm

thick work bench.

ADJUSTING THE POWER TOOL PRIOR TO USE

CAUTION

Make all necessary adjustments before inserting the

plug in the power source.

1. Check to see that the lower guard operates smoothly

CAUTION

䡬 This compound miter saw is equipped with a saw

head lock as safety device.

䡬 To lower the saw head to cut, the lock must be released

by pressing the lock lever (D) with your thumb.

(1) When you push down the handle while pushing the

lock lever (D), check that the lower guard revolves

smoothly (Fig. 7).

(2) Next, check that the lower guard returns to the original

position when the handle is raised.

PRACTICAL APPLICATIONS

WARNING

䡬 To avoid personal injury, never remove or place a

workpiece on the table while the tool is being operated.

䡬 Never place your limbs inside of the line next to

warning sign while the tool is being operated. This

may cause hazardous conditions (see Fig. 8).

CAUTION

䡬 It is dangerous to remove or install the workpiece

while the saw blade is turning.

䡬 When sawing, clean off the shavings from the turntable.

䡬 If the shavings accumulate too much, the saw blade

from the cutting material will be exposed. Never

subject your hand or anything else to go near the

exposed blade.

1. Tightly secure the material by vise assembly to be

cut so that it does not move during cutting

2. Switch operation

Pulling the trigger turns the switch on. Releasing the

trigger turns the switch off.

3. Holder (B) adjustment (Fig. 9)

Loosen the 6 mm bolt with the supplied 10 mm box

wrench. Adjust the holder (B) until its bottom surface

contacts the bench or the floor surface.

4. Using the Vise Assembly (Standard accessory) (Fig. 10)

(1) The vise assembly can be mounted on either the left

fence (Fence (B)) or the right fence (Fence (A)) by

loosening the 6 mm wing bolt (A).

01Eng_C12LCH_WE 3/11/09, 18:4915

16

English

(2) The screw holder can be raised or lowered according

to the height of the workpiece by loosening the 6 mm

wing bolt (B). After the adjustment, firmly tighten the

6 mm wing bolt (B) and fix the screw holder.

(3) Turn the upper knob and securely fix the workpiece

in position.

WARNING

䡬 Always firmly clamp or vise to secure the workpiece

to the fence; otherwise the workpiece might be thrust

from the table and cause bodily harm.

CAUTION

䡬 Always confirm that the motor head does not contact

the vise assembly when it is lowered for cutting. If

there is any danger that it may do so, loosen the 6

mm wing bolt and move the vise assembly to a

position where it will not contact the saw blade.

5. Confirmation for use of sub fence (Fig. 11)

This power tool is equipped with a sub fence. In the

case of direct angle cutting use the sub fence. Then,

you can realize stable cutting of the material with a

wide back face. In the case of left bavel cutting, raise

the sub fence up as illustrated in Fig. 11 and then turn

it counterclockwise.

WARNING

䡬 In the case of left bevel cutting, turn the sub fence

counterclockwise (Fig. 8). Unless it is turned

counterclockwise, the main body or saw blade may

contact the sub fence, resulting in an injury.

6. Using an ink line

Upon lowering the motor section, the lower guard is

raised and the saw blade appears.

Align the ink line with the saw blade.

CAUTION

Never lift the lower guard while the saw blade is

rotating.

The sub fence will not only make contact and

adversely affect cutting accuracy, this could also result

in damage to the guard.

7. Position adjustment of laser line (Only Model

C12LCH/C12FCH)

Ink lining can be easily made on this tool to the laser

marker. A switch lights up the laser marker (Fig. 12).

Turning on the laser marker switch while the digital

display switch is on, light up the laser marker. (On

the C12FCH, only the laser marker switch.)

Depending upon your cutting choice, the laser line

can be aligned with the left side of the cutting width

(saw blade) or the ink line on the right side.

The laser line is adjusted to the width of the saw blade

at the time of factory shipment. Adjust the positions

of the saw blade and the laser line taking the following

steps to suit the use of your choice.

(1) Light up the laser marker and make a groove of about 5

mm deep on the workpiece that is about 38 mm in height

and 89 mm in width. Hold the grooved workpiece by vise

as it is and do not move it.

(2) Then insert a 4 mm hex. bar wrench in the 12 diameter

hole on the side of the gear case, turn the hex. socket

set screw to move the laser line. (If you turn the Hex.

socket screw clockwise, the laser line will shift to the

right and if you turn it counterclockwise, the laser line

will shift to the left.) When you work with the ink line

aligned with the left side of the saw blade, align the

laser line with the left end of the groove (Fig. 13). When

you align it with the right side of the saw blade, align

the laser line with the right side of the groove.

(3) After adjusting the position of the laser line, draw a

right-angle ink line on the workpiece and align the

ink line with the laser line. When aligning the ink line,

slide the workpiece little by little and secure it by vise

at a position where the laser line overlaps with the

ink line. Work on the grooving again and check the

position of the laser line. If you wish to change the

laser line’s position, make adjustments again

following the steps from (1) to (3).

WARNING (Fig. 15 and Fig. 16)

䡬 Make sure before plugging the power plug into the

receptacle that the main body and the laser marker

are turned off.

䡬 Exercise utmost caution in handling a switch trigger

for the position adjustment of the laser line, as the

power plug is plugged into the receptacle during

operation.

If the switch trigger is pulled inadvertently, the saw

blade can rotate and result in unexpected accidents.

䡬 Do not remove the laser marker to be used for other

purposes.

CAUTION

䡬 Laser radiation - Do not stare into beam.

䡬 Laser radiation on work table. Do not stare into beam.

If your eye is exposed directly to the laser beam, it

can be hurt.

䡬 Do not dismantle it.

䡬 Do not give strong impact to the laser marker (main

body of tool); otherwise, the position of a laser line

can go out of order, resulting in the damage of the

laser marker as well as a shortened service life.

䡬 Keep the laser marker lit only during a cutting

operation. Prolonged lighting of the laser marker can

result in a shortened service life.

䡬 Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

NOTE

䡬 Perform cutting by overlapping the ink line with the

laser line.

䡬 When the ink line and the laser line are overlapped,

the strength and weakness of light will change,

resulting in a stable cutting operation because you

can easily discern the conformity of lines. This ensures

the minimum cutting errors.

䡬 In outdoor or near-the-window operations, it may

become difficult to observe the laser line due to the

sunlight. Under such circumstances, move to a place

that is not directly under the sunlight and engage in

the operation.

䡬 Do not tug on the cord behind the motor head or hook

your finger, wood and the like around it; otherwise,

the cord may come off and the laser marker may not

be lit up.

䡬 Check and make sure on a periodic basis if the position

of the laser line is in order. As regards the checking

method, draw a right-angle ink line on the workpiece

with the height of about 38 mm and the width of 89

mm, and check that the laser line is in line with the

ink line [The deviation between the ink line and the

laser line should be less than the ink line width (0.5

mm)] (Fig. 14).

8. Digital display panel (for C12LCH and C12LC) (Fig. 17

and Fig. 18)

(1) Turning on the digital display switch shows 0° for both

miter and bevel angle, regardless of main unit angle.

01Eng_C12LCH_WE 3/11/09, 18:4916

17

English

(2) Align the main unit angle with the tilt angle (0°) and

miter angle (0°) and hold down their reset buttons for

at least 0.2 seconds.

(3) Turning on the laser marker switch while the digital

display switch is on, lights up the laser marker. (On

the C12FCH, only the laser marker switch.)

CAUTION

䡬 When operating the digital panel, have the motor head

section at the top limit position and the blade stopped.

䡬 If the figure shown on the miter angle digital display

is different from the positive stop angle (for example,

45.0° → 45.5°, 31.6° → 32.0°) then the positive stop

has probably deviated slightly from its correct

position. If this happens, do as follows.

(1) Move the turntable left and right with the side

handle loosened, and set the turntable to the

correct position.

(2) If the figures on the display and positive stop still

do not match, then return the turntable to the 0°

position. Next move the turntable left and right

with the side handle loosened as shown in Fig.

19. After setting it to the correct position 0°, press

the reset button again.

NOTE

䡬 Before starting to cut, align the main unit to the miter

angle 0° and the bevel angle 0° and hold down the

reset buttons for at least 0.2 seconds. If you press the

digital display switch to ON without aligning the main

unit to 0°, then the figures appearing on the digital

display and the main unit angle will not match.

䡬 The laser marker will not light up if the digital display

switch is turned off. (only on C12LCH)

䡬 Do not use the main unit near equipment that

generates electrical noise such as generators.

Electrical noise might cause faulty readings or

operation on the digital display.

9. Cutting operation

(1) As shown in Fig. 20 the width of the saw blade is the

width of the cut. Therefore, slide the workpiece to the

right (viewed from the operator’s position) when

length

is desired, or to the left when length is

desired.

(Only Model C12LCH/C12FCH)

If a laser marker is used, align the laser line with the

left side of the saw blade, and then align the ink line

with the laser line.

(2) Once the saw blade reaches maximum speed, slowly

push down the handle while pushing the lock lever

(D) and bring the saw blade in the vicinity of the

material to be cut.

(3) Once the saw blade contacts the workpiece, push the

handle down gradually to cut into the workpiece.

(4) After cutting the workpiece to the desired depth, turn

the power tool OFF and let the saw blade stop

completely before raising the handle from the

workpiece to return it to the full retract position.

CAUTION

䡬 For maximum dimensions for cutting, refer to

“SPECIFICATIONS” table.

䡬 Increased pressure on the handle will not increase the

cutting speed. On the contrary, too much pressure

may result in overload of the motor and/or decreased

cutting efficiency.

䡬 Confirm that the trigger switch is turned OFF and the

power plug has been removed from the receptacle

whenever the tool is not in use.

䡬 Always turn the power off and let the saw blade stop

completely before raising the handle from the

workpiece. If the handle is raised while the saw blade

is still rotating, the cut-off piece may become jammed

against the saw blade causing fragments to scatter

about dangerously.

䡬 Every time one cutting of deep-cutting operation is

finished, turn the switch off, and check that the saw

blade has stopped. Then raise the handle, and return

it to the full retract position.

䡬 Be absolutely sure to remove the cut material from

the top of the turntable, and then proceed to the next

step.

10. Miter cutting procedures

(1) Loosen the side handle and push the lever for angle

stoppers. Then, adjust the turntable until the indicator

aligns with desired setting on the miter scale (Fig. 21).

(2) Re-tighten the side handle to secure the turntable in

the desired position.

NOTE

䡬 Positive stops are provided at the right and left of the

0° center setting, at 15°, 22.5°, 31.6° and 45° settings.

Check that the miter scale and the tip of the indicator

are properly aligned.

䡬 Operation of the saw with the miter scale and indicator

out of alignment, or with the side handle not properly

tightened, will result in poor cutting precision.

CAUTION

䡬 Never remove the side handle; use of the tool without

it would be hazardous.

To prevent an accident or personal injury always firmly

tighten the miter handle.

11. Bevel cutting procedures (Fig. 22)

(1) Loosen the clamp lever and bevel the saw blade to

the left.

(2) Adjust the bevel angle to the desired setting while

watching the bevel angle scale and indicator, then

secure the clamp lever.

WARNING

䡬 When the workpiece is secured on the left or right

side of the blade, the short cut-off portion will come

to rest on the right or left side of the saw blade. Always

turn the power off and let the saw blade stop

completely before raising the handle from the

workpiece.

If the handle is raised while the saw blade is still

rotating, the cut-off piece may become jammed

against the saw blade causing fragments to scatter

about dangerously.

䡬 When stopping the bevel cutting operation halfway,

start cutting after pulling back the motor head to the

initial position.

Starting from halfway, without pulling back, causes

the safety cover to be caught in the cutting groove of

the workpiece and to contact the saw blade.

12. Bevel angle fine adjustment (Fig. 23 and Fig. 24)

(1) Grip the handle on the motor head and position it at

the bevel angle you need. Temporarily tighten the

clamp lever.

CAUTION

䡬 If not tightened firmly enough the motor head might

suddenly move or slip, causing injuries. Be sure to

tighten the motor head section enough so it will not

move.

(2) Make fine adjustments to the bevel angle by gripping

the handle and moving the knob (A).

01Eng_C12LCH_WE 3/11/09, 18:4917

18

English

NOTE

䡬 Turning knob (A) clockwise, allows fine adjustment

of the main unit to the left (as seen from front).

Turning knob (A) counterclockwise, allows fine

adjustment of the main unit to the right (as seen from

front).

If you tilt the main unit in the direction that does not

place a load on plate (A) and pull plate (A), the contact

position changes and the right slope angle becomes

3°.

If you tilt the main unit in the direction that does not

place a load on plate (B) and pull plate (B), the contact

position changes and the right slope angle becomes

48°.

(3) After adjusting to the desired angle, tighten the clamp

lever and clamp the motor head.

CAUTION

䡬 Always check that the clamp lever is secured and the

motor head is clamped. If you attempt angle cutting

without clamping the motor head, then the motor

head might shift unexpectedly causing injuries.

13. Compound cutting procedures

Compound cutting can be performed by following the

instructions in 10 and 11 above. For maximum

dimensions for compound cutting, refer to

“SPECIFICATIONS” table.

CAUTION

䡬 Always secure the workpiece with the right hand side

for compound cutting. Never rotate the table to the

right for compound cutting, because the saw blade

might then contact the clamp or vise that secures the

workpiece, and cause personal injury or damage.

14. Cutting long materials

When cutting long materials, use an auxiliary platform

which is the same height as the holder (optional

accessory) and base of the special auxiliary

equipment.

Capacity: wooden material (W × H × L)

200 mm × 50 mm × 1400 mm

15. Installing the holders (Optional accessory)

The holders help keep longer workpieces stable and

in place during the cutting operation.

(1) As indicated in Fig. 25, use a steel square for aligning

the upper edge of the holders with the base surface.

Loosen the 6 mm wing nut. Turn a height adjustment

bolt 6 mm, and adjust the height of the holder.

(2) After adjustment, firmly tighten the wing nut and

fasten the holder with the 6 mm knob bolt (optional

accessory). If the length of Height Adjustment Bolt 6

mm is insufficient, spread a thin plate beneath. Make

sure the end of Height Adjustment Bolt 6 mm does

not protrude from the holder.

16. Stopper for precision cutting (Stopper and holder are

optional accessory)

The stopper facilitates continuous precision cutting

in lengths of 280 mm to 450 mm.

To install the stopper, attach it to the holder with the

6 mm wing bolt as shown in Fig. 26.

17. Confirmation for use Crown molding vise, Crown

molding Stopper (L) and (R) (Optional accessory)

(1) Crown molding Stopper (L) and (R) (optional

accessories) allow easier cuts of crown molding

without tilting the saw blade. lnstall them in the base

both-sides side to be shown in Fig. 27. After inserting

tighten the 6 mm knob bolts to secure the Crown

molding Stoppers.

(2) The crown molding vise (B) (Optional accessory) can

be mounted on either the left fence (Fence (B)) or the

right fence (Fence (A)). lt can unite with the slope of

the crown molding and vice can be pressed down.

Then turn the upper knob, as necessary, to securely

attach the crown molding in position. To raise or lower

the vise assembly, first loosen the 6 mm wing bolt.

After adjusting the height, firmly tighten the 6 mm

wing bolt; then turn the upper knob, as necessary, to

securely attach the crown molding in position (See

Fig 28).

Position crown molding with its WALL CONTACT

EDGE against the guide fence and its CEILING

CONTACT EDGE against the Crown molding Stoppers

as shown in Fig. 28. Adjust the Crown molding

Stoppers according to the size of the crown molding.

Tighten the 6 mm wing bolt to secure the Crown

molding Stoppers.

WARNING

䡬 Always firmly clamp or vise to secure the crown

molding to the fence; otherwise the crown molding

might be thrust from the table and cause bodily harm.

Do not bevel cutting. The main body or saw blade

may contact the sub fence, resulting in an injury.

CAUTION

䡬 Always confirm that the motor head (see Fig. 1) does

not contact the crown molding vise assembly when it

is lowered for cutting. If there is any danger that it

may do so, loosen the 6 mm knob bolt and move the

crown molding vise assembly to a position where it

will not contact the saw blade.

MOUNTING AND DISMOUNTING SAW BLADE

WARNING

䡬 To prevent an accident or personal injury, always turn off

the trigger switch and disconnect the power plug from

the receptacle before removing or installing a blade.

If cutting work is done in a state where the bolt is not

sufficiently tightened, the bolt can get loose, the blade

can come off, and the lower guard can get damaged,

resulting in injuries.

Also, check that the bolts are properly tightened before

plugging the power plug into the receptacle.

䡬 If the bolts are attached or detached using tools other

than the 17 mm box wrench (standard accessory),

excessive or improperly tightening occurs, resulting

in injury.

1. Mounting the saw blade (Fig. 29, Fig. 30, Fig. 31 and

Fig. 32)

(1) Rotate the lower guard (plastic) to the top position.

(2) Use the driver to loosen the 5 mm screw fastening

the spindle cover and then remove the spindle cover.

(3) Press in spindle lock and loosen bolt with 17 mm box

wrench (standard accessory).

Since the bolt is left-hand threaded, loosen by turning

it to the right as show in Fig. 31.

NOTE

䡬 If the spindle lock cannot be easily pressed in to lock

the spindle, turn the bolt with 17 mm box wrench

(standard accessory) while applying pressure on the

spindle lock.

The saw blade spindle is locked when the spindle lock

is pressed inward.

(4) Remove the bolt and washer (D).

(5) Lift the lower guard and mount the saw blade.

01Eng_C12LCH_WE 3/11/09, 18:4918

19

English

WARNING

When mounting the saw blade, confirm that the

rotation indicator mark on the saw blade and the

rotation direction of the gear case (see Fig. 1) are

properly matched.

(6) Thoroughly clean washer (D) and the bolt, and install

them onto the saw blade spindle.

(7) Press in the spindle lock and tighten the bolt by turning

it to the left by standard accessories wrench (17 mm

box wrench) as indicated in Fig. 31.

CAUTION

䡬 Confirm that the spindle lock has returned to the

retract position after installing or removing the saw

blade.

䡬 Tighten the bolt so it does not come loose during

operation.

Confirm that the bolt has been properly tightened

before the power tool is started.

2. Dismounting the saw blade

Dismount the saw blade by reversing the mounting

procedures described in paragraph 1 above.

The saw blade can easily be removed after lifting the

lower guard.

CAUTION

䡬 Never attempt to install saw blades except

290 mm – 305 mm in diameter.

MAINTENANCE AND INSPECTION

WARNING

To avoid an accident or personal injury, always

confirm the trigger switch is turned OFF and that the

power plug has been disconnected from the

receptacle before performing any maintenance or

inspection of this tool.

1. Inspecting the saw blade

Always replace the saw blade immediately upon the

first sign of deterioration or damage.

A damaged saw blade can cause personal injury and

a worn saw blade can cause ineffective operation and

possible overload to the motor.

CAUTION

䡬 Never use a dull saw blade. When a saw blade is dull,

its resistance to the hand pressure applied by the tool

handle tends to increase, making it unsafe to operate

the power tool.

2. Inspecting the lever (Fig. 33 and Fig. 34)

If the M8 hexagonal head bolts (2) are loose, align the

sides of the fence and saw blade with the steel square.

After adjusting the saw blade and fence to a ninety-

degree angle, tighten the lever securing hexagonal

head bolts (2).

3. Inspecting the carbon brushes (Fig. 35 and Fig. 36)

The carbon brushes in the motor are expendable parts.

If the carbon brushes become excessively worn, motor

trouble might occur.

Therefore, inspect the carbon brushes periodically and

replace them when they have become worn to the

wear limit line as shown in Fig. 35.

Also, keep the carbon brushes clean so that they will

slide smoothly within the brush holders.

The carbon brushes can easily be removed after

removal of the brush caps (see Fig. 36) with a slotted

(minus) screwdriver.

4. About Handling the Motor (see Fig. 1)

Winding of the motor is said to be the heart of this

tool. Exercise utmost caution not to damage the

winding by exposing it to wash oil or water.

NOTE

䡬 Accumulation of dust and the like inside the motor

can result in a malfunction.

After using the motor for 50 hours or so, carry out no-

load running, and blow in the dry air from a wind hole

at the motor's rear. Such action is effective to

discharge dust and the like.

5. Inspecting the screws

Regularly inspect each component of the power tool

for looseness.

Re-tighten screws on any loose part.

WARNING

䡬 To prevent personal injury, never operate the power

tool if any components are loose.

6. Inspecting the lower guard for proper operation

Before each use of the tool, test the lower guard (see

Fig. 7) to assure that it is in good condition and that it

moves smoothly.

Never use the tool unless the lower guard operates

properly and it is in good mechanical condition.

7. Storage

After operation of the tool has been completed, check

that the following has been performed:

(1) Trigger switch is in OFF position,

(2) Power plug has been removed from the receptacle,

(3) When the tool is not in use, keep it stored in a dry

place out of the reach of children.

8. Lubrication

Lubricate the following sliding surfaces once a month

to keep the power tool in good operating condition

for a long time (Fig. 1 and Fig. 2).

Use of machine oil is recommended.

Oil supply points:

* Rotary portion of hinge

* Rotary portion of vise assembly

9. Cleaning

Periodically remove chips, dust and other waste

material from the surface of the power tool, especially

from the inside of the lower guard with a damp, soapy

cloth. To avoid a malfunction of the motor, protect it

from contact with oil or water.

(Only Model C12LCH/C12FCH)

If the laser line becomes invisible due to chips and the

like adhered onto the window of the laser marker's light-

emitting section, wipe and clean the window with a dry

cloth or a soft cloth moistened with soapy water, etc.

10. Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

Especially laser device should be maintained by the

authorised agent by laser manufacturer.

Always assign the repair of laser device to Hitachi

Authorised Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

01Eng_C12LCH_WE 3/11/09, 18:4919

20

English

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: -Neutral

Brown: -Live

As the colours of the wires in the main lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal

marked with the letter L or coloured red. Neither code

must be connected to the earth terminal.

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN61029.

The typical A-weighted sound pressure level: 95 dB (A)

The typical A-weighted sound power level: 108 dB (A)

Wear ear protection.

The typical weighted root mean square acceleration

value: 2.6 m/s

2

.

Information for power supply system to be used with

electric tools provided with rated voltage 230 V~

Switching operations of electric apparatus cause voltage

fluctuations.

The operation of this electric tool under unfavorable mains

conditions can have adverse effects to the operation of other

electric apparatus.

With a mains impedance equal or less than 0.29 Ohms

there will probably be no negative effects.

Usually, the maximum permissible mains impedance will

not be exceeded when the branch to the power outlet is

fed from a junction box with a service capacity of 25

ampere or higher.

In case of power failure, or when the power plug is pulled

out, immediately return the switch to OFF position. This

prevents an uncontrolled restart.

01Eng_C12LCH_WE 3/11/09, 18:4920

Page is loading ...

85

C12LCH (1/3)

ABC D

1 323-141 1

2 323-137 1

3 323-138 1

4 949-900 1 D3 × 14

5 323-142 2

6 962-782 1 M5 × 6

7 949-531 1 D2 × 12

8 323-144 1 M5

9 975-144 1

10 323-139 1 "11"

11

–––––––––––

1

12 323-647 1

13 323-143 2

14 323-140 1

15 323-136 1

16 323-208 1 M6 × 20

17 322-935 1

18 323-665 1 M10

19 323-666 1

20 323-597 1

21 304-043 1 M4 × 10

22 323-598 1

23 323-599 1

24 949-821 1 M5 × 16

25 949-454 1

26 323-596 1

27 322-933 1

28 322-934 1 M16

29 323-593 1

30 323-663 1

31 993-539 1 M4 × 16

32 980-523 1

33 323-600 1

34 949-241 1 M5 × 20

35 949-432 1 M6

36 323-142 2

37 323-619 1

38 949-216 4 M4 × 10

39 307-956 1 M6 × 10

40 323-594 1

41 323-595 1

42 323-684 1

43 302-518 1 "44"

44 984-528 1 P-6

45 323-601 1 "47-49"

46 990-541 2 M5 × 16

47 323-602 1

ABC D

48 322-963 1

49 949-214 1 M4 × 6

50 949-431 1 M5

51 949-454 1 M5

52 949-821 1 M5 × 16

53 323-664 1 "54"

54 949-900 1 D3 × 14

55 949-660 2 M6 × 20

56 323-683 1

57 949-221 2 M4 × 20

58 949-423 2 M4

59 323-142 2

60 303-006 2 D4 × 10

61 949-432 2 M6

62 323-662 1

63 323-661 1

64 323-659 1

65 303-409 2 M8 × 25

66 935-196 2 M4 × 12

67 322-893 1

68 304-043 1 M4 × 10

69 680-418 1 M12

70 949-217 2 M4 × 12

71 949-423 2 M4

72 323-607 1

74 323-627 1

75 949-457 2 M8

76 949-655 2 M8 × 16

77 323-609 1

78 307-635 2 M4 × 10

79 323-680 1

80 323-646 1 "1-10,12-15"

09Back_C12LCH_WE 3/12/09, 17:0185

Page is loading ...

88

C12LC (1/3)

ABC D

16 323-208 1 M6 × 20

17 322-935 1

18 323-665 1 M10

19 323-666 1

20 323-597 1

21 304-043 1 M4 × 10

22 323-598 1

23 323-599 1

24 949-821 1 M5 × 16

25 949-454 1

26 323-596 1

27 322-933 1

28 322-934 1 M16

29 323-593 1

30 323-663 1

31 993-539 1 M4 × 16

32 980-523 1

33 323-600 1

34 949-241 1 M5 × 20

35 949-432 1 M6

36 323-142 2

37 323-619 1

38 949-216 4 M4 × 10

39 307-956 1 M6 × 10

40 323-594 1

41 323-595 1

42 323-684 1

43 302-518 1 "44"

44 984-528 1 P-6

45 323-601 1 "47-49"

46 990-541 2 M5 × 16

47 323-602 1

ABC D

48 322-963 1

49 949-214 1 M4 × 6

50 949-431 1 M5

51 949-454 1 M5

52 949-821 1 M5 × 16

53 323-664 1 "54"

54 949-900 1 D3 × 14

56 323-683 1

57 949-221 2 M4 × 20

58 949-423 2 M4

59 323-142 2

60 303-006 2 D4 × 10

61 949-432 2 M6

62 323-662 1

63 323-661 1

64 323-659 1

65 303-409 2 M8 × 25

66 935-196 2 M4 × 12

67 322-893 1

68 304-043 1 M4 × 10

69 680-418 1 M12

70 951-039 2 M4 × 12

71 949-423 2 M4

72 323-607 1

74 323-627 1

75 949-457 2 M8

76 949-655 2 M8 × 16

77 323-609 1

78 307-635 2 M4 × 10

79 323-680 1

09Back_C12LCH_WE 3/12/09, 17:0188

Page is loading ...

91

C12FCH (1/3)

ABC D

1 323-141 1

2 323-137 1

3 323-138 1

4 949-900 1 D3 × 14

5 323-142 2

6 962-782 1 M5 × 6

7 949-531 1 D2 × 12

8 323-144 1 M5

9 975-144 1

10 323-139 1 "11"

11

–––––––––––

1

12 323-647 1

13 323-143 2

14 323-140 1

15 323-136 1

16 323-208 1 M6 × 20

17 322-935 1

18 323-665 1 M10

19 323-666 1

20 323-597 1

21 304-043 1 M4 × 10

22 323-598 1

23 323-599 1

24 949-821 1 M5 × 16

25 949-454 1

26 323-596 1

27 322-933 1

28 322-934 1 M16

29 323-593 1

30 323-663 1

39 307-956 1 M6 × 10

40 323-594 1

41 323-595 1

42 323-684 1

43 302-518 1 "44"

44 984-528 1 P-6

45 323-719 1 "47-49"

46 990-541 2 M5 × 16

47 323-697 1

ABC D

48 322-963 1

49 949-214 1 M4 × 6

50 949-431 1 M5

51 949-454 1 M5

52 949-821 1 M5 × 16

53 323-664 1 "54"

54 949-900 1 D3 × 14

55 949-660 2 M6 × 20

56 323-683 1

57 949-221 2 M4 × 20

58 949-423 2 M4

59 323-142 2

60 303-006 2 D4 × 10

61 949-432 2 M6

62 323-662 1

63 323-661 1

64 323-659 1

65 303-409 2 M8 × 25

66 935-196 2 M4 × 12

67 322-893 1

68 304-043 1 M4 × 10

69 680-418 1 M12

74 323-627 1

75 949-457 2 M8

76 949-655 2 M8 × 16

77 323-609 1

78 307-635 2 M4 × 10

79 323-680 1

80 323-646 1 "1-10,12-15"

09Back_C12LCH_WE 3/12/09, 17:0191

Page is loading ...

94

English

Nederlands

GUARANTEE CERTIFICATE

1 Model No.

2 Serial No.

3 Date of Purchase

4 Customer Name and Address

5 Dealer Name and Address

(Please stamp dealer name and address)

Italiano Ελληνικά

Français Português

Deutsch

Español

GARANTIEBEWIJS

1 Modelnummer

2 Serienummer

3 Datum van aankoop

4 Naam en adres van de gebruiker

5 Naam en adres van de handelaar

(Stempel a.u.b. naam en adres vande de

handelaar)

GARANTIESCHEIN

1 Modell-Nr.

2 Serien-Nr.

3 Kaufdaturn

4 Name und Anschrift des Kunden

5 Name und Anschrift des Händlers

(Bitte mit Namen und Anschrift des

Handlers abstempeln)

CERTIFICADO DE GARANTIA

1 Número de modelo

2 Número de serie

3 Fecha de adquisición

4 Nombre y dirección del cliente

5 Nombre y dirección del distribudor

(Se ruega poner el sellú del distribudor

con su nombre y dirección)

CERTIFICAT DE GARANTIE

1 No. de modèle

2 No. de série

3 Date d'achat

4 Nom et adresse du client

5 Nom et adresse du revendeur

(Cachet portant le nom et l'adresse du

revendeur)

CERTIFICADO DE GARANTIA

1 Número do modelo

2 Número do série

3 Data de compra

4 Nome e morada do cliente

5 Nome e morada do distribuidor

(Por favor, carímbe o nome e morada

do distribuidor)

CERTIFICATO DI GARANZIA

1 Modello

2 N° di serie

3 Data di acquisto

4 Nome e indirizzo dell'acquirente

5 Nome e indirizzo del rivenditore

(Si prega di apporre il timbro con questi

dati)

¶π™∆√¶√π∏∆π∫√ ∂°°À∏™∏™

1 Αρ. Μντέλυ

2 Αύων Αρ.

3 Ηµερµηνία αγράς

4 ΄νµα και διεύθυνση πελάτη

5 ΄νµα και διεύθυνση µεταπωλητή

(Παρακαλύµε να ρησιµπιηθεί

σραγίδα)

✄

09Back_C12LCH_WE 3/12/09, 17:0194

95

1

2

3

4

5

✄

09Back_C12LCH_WE 3/12/09, 17:0195

96

09Back_C12LCH_WE 3/12/09, 17:0196

97

09Back_C12LCH_WE 3/12/09, 17:0197

98

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 willich 1, F. R. Germany

Tel: +49 2154 49930

Fax: +49 2154 499350

URL: http://www.hitachi-powertools.de

Hitachi Power Tools Netherlands B. V.

Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands

Tel: +31 30 6084040

Fax: +31 30 6067266

URL: http://www.hitachi-powertools.nl

Hitachi Power Tools (U. K.) Ltd.

Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom

Tel: +44 1908 660663

Fax: +44 1908 606642

URL: http://www.hitachi-powertools.co.uk

Hitachi Power Tools France S. A. S.

Prac del’ Eglantier 22, rue des Crerisiers Lisses, C. E. 1541,

91015 EVRY CEDEX, France

Tel: +33 1 69474949

Fax: +33 1 60861416

URL: http://www.hitachi-powertools.fr

Hitachi Power Tools Belgium N.V. / S.A.

Koningin Astridlaan 51, 1780 Wemmel, Belgium

Tel: +32 2 460 1720

Fax: +32 2 460 2542

URL http://www.hitachi-powertools.be

Hitachi Fercad Power Tools Italia S.p.A

Via Retrone 49-36077, Altavilla Vicentina (VI), Italy

Tel: +39 0444 548111

Fax: +39 0444 548110

URL: http://www.hitachi-powertools.it

Hitachi Power Tools lberica, S.A.

C / Migjorn, s/n, Poligono Norte, 08226 Terrassa, Barcelona, Spain

Tel: +34 93 735 6722

Fax: +34 93 735 7442

URL: http://www.hitachi-powertools.es

Hitachi Power Tools Österreich GmbH

Str. 7, Objekt 58/A6, Industriezentrum NÖ –Süd 2355

Wiener Neudorf, Austria

Tel: +43 2236 64673/5

Fax: +43 2236 63373

09Back_C12LCH_WE 3/12/09, 17:0198

Page is loading ...

Hikoki C 10FCH Owner's manual

Hikoki C 10FCH Owner's manual

in other languages

Related papers

Other documents