1
AST206*
Bike Trailer
Jogger Kit
Owner’s Manual
WARNING
IMPORTANT!
KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
ADULT ASSEMBLY REQUIRED
NO TOOLS REQUIRED
For Ages 6 months to 50 lbs.
*Model AST206 Jogger Kit only for use with Allen Sports trailer model AST200.
Consumer Information
WARNING
2
• Do not use your Allen Sports Jogger Stroller if any part is damaged or missing
• Never leave child unattended
• Avoid serious injury from falling or sliding out. Always use safety restraint
harness.
• Never hang items from handlebar, as it may result in tip over or loss of control
• Do not skate with your Jogger stroller. Always use wrist strap.
• Maximum load for seatback storage pockets is 2 lbs. Max weight for storage
basket is 5lbs.
• The stroller may become unstable if any of the manufacturers’ recommended
weight loads are exceeded.
• Take care to avoid injury to fingers when unfolding and folding frame. Keep child
away from stroller when preparing the stroller for use, making adjustments, or
folding for transport or storage.
• Check that all folding elements are secure and operating correctly before each
use.
• Do not inflate tires above 25-30 PSI. Always use a hand or foot pump to inflate
tires.
CAUTION
• Follow all manufacturer’s instructions
• Put on all the brakes whenever you park the stroller
• Do not leave children unattended
• Do not carry extra children or bags on this stroller
• Make sure children are clear of any moving parts if you adjust the stroller.
Otherwise they may be injured.
• A child’s safety is your responsibility
Please read these instructions before assembly and use of this product
3
• This manual contains valuable information concerning the safe operation of this
stroller. Keep it in a convenient place for future reference regarding safe
operation and maintenance.
• Failure to read and follow the instructions provided in the manual can result in
serious injury or death of your child.
• If you have any questions regarding the operation of this product, please refer to
this owner’s manual or contact your dealer
• Adult assembly is required.
• No tools are required.
• Product features and decorations may vary from photo.
Safety Information
• The Jogger Stroller is designed to carry two children from 6 months to 50lbs.
• Adjust the harness as per the manufacturer’s instructions
• The child must be kept clear of all moving parts during folding or adjusting the
stroller
• This product is not designed for in-line skating. Always use wrist strap.
• Do not carry additional items or children in this stroller except as advised in this
owner’s manual. Failure to comply may cause damage to the stroller and / or
make it unstable.
• Overloading or incorrect folding may cause damage to the stroller
• Never use stroller on stairs or escalator.
• Do not use stroller near open flame or fire, and never leave exposed to heat
sources or direct sunlight
• Do not place items on top of canopy.
• Do not hang shopping bags on stroller, as an unstable condition may result.
• Maximum load for seatback storage pockets is 2 lbs. Max weight for storage
basket is 5lbs.
• Use parking brake when loading or unloading stroller.
• Brake is only to be used for parking.
Parts
4
WARNING
Plastic bags used for packing can create a suffocation hazard. Dispose of these
immediately upon removing stroller components. Keep all packing materials away from
young children.
IMPORTANT! Please remove all parts from the package and identify them before
assembly.
1. Fork Assembly with connect tube +4 bolts
2. Hand Brake with Lever and Cable
3. 16” Front Wheel (1) (Not Shown)
Fork Connect Tube
Hand Brake Lever
Fork Assembly
5
Assembly
IMPORTANT! Before assembly and each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are
missing or broken. Contact your retailer for replacement parts and instructions if
needed. Never substitute parts.
• Remove the trailer hitch arm by removing QR pin (#1) and press the spring (#2)
(and pull the arm out.
• Assemble on side of the front fork cross brace (#3) as shown above, using 2
socket head screws (#4) provided – at this point, just snug the screws, do not
tighten completely
• Insert the jogger arm you have just assembled into one of the aluminum hitch
arm brackets (#5) on the frame, sliding in until the spring pin (#3) locks in place.
• Take the other arm, and insert in the bracket on the opposite side of the frame,
sliding in until the spring pin locks in place.
• Insert remaining 2 screws in holes provided in the fork leg (#7), and tighten
loosely in the support bracket.
• Install wheel in slots in plastic fork ends, aligning the axle which has a flat side to
match the slot in the fork end.(#8)
• Once wheel is in place and Quick release lever (#9) locked in place, tighten the 4
screws to secure the front fork assembly (#10).
3. Photo of inspecting
installation by pulling
out on wheel
#1
#2
#3
#4
#5
#7
#8
#9
#10
6
Connecting Brake
• The Jogger kit includes a hand-operated V-brake caliper for use while running.
To connect the brake, simply squeeze the brake caliper (#11) together, while
pulling the curved metal tube cable housing (#13), and insert the cable ferrule
(#12) into the metal bracket on the opposing brake arm. This fixes the brake
caliper and allows your brake to function properly.
.
• After Cable is installed you must run the cable up the left side of the canopy.
Fixing the cable under the Velcro tabs that hold the cover in place as shown.
o
• Next, attach the brake lever clamp to the handlebar center by loosening and
retightening the hand knob.
#11
#12
#13
#14
#7
7
Front Wheel Assembly
IMPORTANT: PLEASE FOLLOW INSTRUCTIONS FOR QUICK RELEASE LEVER
The Allen Sports Jogging Stroller is equipped with a Quick Release front wheel. Place
the Stroller so the rear wheels and handle are touching the floor. The front axle has a
flat area on it that you must align with the slots in the front fork. After aligning the front
wheel in the fork slots, slide the wheel all the way into the front fork. With the wheel in
position and the quick release lever in the “Open” position, tighten the finger nut on the
axle until it is very close to contacting the fork. Move the lever into the “Closed” position.
You should feel significant resistance when closing the lever. If you do not, open the
lever and tighten the finger nut a bit more and close the lever again. Continue to do this
until the movement of the lever results in tension on the lever when closing and the
wheel is tight in the frame. When you complete the wheel installation process, attempt
to pull wheel from frame; if wheel moves, tighten the finger nut and repeat the test.
CAUTION: You cannot tighten the Quick Release lever by merely twisting the
lever. You can only ensure it is locked by properly tightening the finger nut and
then flipping the Quick Release lever from “Open” to “Closed”
WARNING: Failure to properly install and adjust wheels with Quick Release
levers could allow wheel to come off during use. This could lead to serious injury or
death.
Removal
#15
8
• To remove the jogger kit, first take off the brake lever by loosening and removing
the hand knob (#16) on the lever bracket (#17).
• Then release the brake, remove the front wheel,
• Remove the two screws from one side of the cross support tube.(#7)
• Finally, remove the QR pins(#18) from the aluminum frame brackets (#19),
depress the spring pin (#20), and pull out the arms.
,
Maintenance
We recommend that you have an experienced mechanic perform the following checks
and lubricate required areas once a year.
• All pivot points - Lubricate and check fasteners, such as nuts and bolts.
• Wheel Axles - Lubricate, adjust and check for signs of wear
• Folding mechanism - Lubricate, adjust and check for signs of wear
• Handbrake - Lubricate pivot point, adjust and check for signs of wear.
• Tires - Check tires regularly for proper inflation. Inflate to 20-30 PSI range.
Lower pressures give a softer ride. Always use a hand or foot pump to inflate
tires.
• To maintain the safety and performance of your jogger kit, use only original
equipment replacement parts available from the service center or your retailer.
Use of non-approved replacement parts and accessories will void
manufacturer’s warranty.
WARRANTY INFORMATION:
ALLEN SPORTS USA
If your product requires warranty service, do not return it to retail location where it was purchased. Contact:
(800) 722-5536 ~ [email protected]
Please note that all returns and exchanges are subject to the return policy of the retailer
where the product was originally purchased
R. A. ALLEN CO., INC. - 505 BEACHLAND BLVD. - STE. 5 - VERO BEACH, FL 32963
#19
#20
#18
/
