Miele PDR 922 Operating instructions

Operating and Installation Instructions

Commercial Tumble Dryers

PDR914/918/922/928/944

To prevent accidents and machine damage,

read these instructions before installation or

use.

en-US, CA

M.-Nr. 11 786 010

2

WARNING: FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or

property damage.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas sup-

plier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency

or the gas supplier. (In Massachusetts, installation must be performed by a li-

censed installer/gas fitter.)

To reduce the risk of severe injury or death follow all installation instructions.

Do not install a clothes dryer with flexible plastic venting materials. If flexible metal

(foil type) duct is installed, use duct that has been investigated and found accept-

able for use with clothes dryers. Flexible venting materials are known to collapse,

be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow

and increase the risk of fire.

Save these instructions.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

Instructions to be followed in the event the user smells gas and the "For Your Safety" cau-

tion above must be posted in a prominent location. The information to be posted shall be

obtained by consulting with the local gas supplier.

Caring for the environment

3

Disposal of the packaging material

The packaging material protects the dryer from transport damage.

The packaging materials used are selected from materials which are

environmentally friendly for disposal and can therefore be recycled.

Recycling the packaging material reduces the use of raw materials in

the manufacturing process and also reduces the amount of waste in

landfill sites. Your dealer will take the packaging material away.

Disposing of your old machine

Old electrical and electronic machines often contain valuable materi-

als. However, they also contain harmful substances which were es-

sential for their correct functioning and safety. These could be haz-

ardous to human health and to the environment if disposed of with

household waste or if handled incorrectly. Therefore, please do not

dispose of your old machine with household waste.

Please dispose of it at your local community waste collection/recy-

cling center for electrical and electronic machines. Consult your

dealer if necessary.

Please ensure that your old machine poses no risk to children while

being stored for disposal.

Contents

4

Caring for the environment ............................................................................................ 3

IMPORTANT SAFETY INSTRUCTIONS ......................................................................... 8

Appropriate use................................................................................................................. 8

Preventing misuse ............................................................................................................. 9

Technical safety................................................................................................................. 9

Dryers with gas heating ................................................................................................ 11

Correct use........................................................................................................................ 12

Accessories ....................................................................................................................... 13

Description of the machine ............................................................................................ 14

Operating the tumble dryer ............................................................................................ 15

Control panel..................................................................................................................... 15

Sensor buttons and touch display with sensor buttons.................................................... 16

Main menu......................................................................................................................... 16

“Programs” menu .................................................................................................... 16

“Favorites” menu...................................................................................................... 16

“Supervisor” menu.................................................................................................. 16

Operating examples .......................................................................................................... 16

Option lists .................................................................................................................... 16

Setting numerical values............................................................................................... 17

Pull-down menu ............................................................................................................ 18

Exiting the menu ........................................................................................................... 18

Help display .................................................................................................................. 18

Before using for the first time ........................................................................................ 19

Switching on the tumble dryer .......................................................................................... 19

Reference to optional external machines.......................................................................... 19

Setting the display brightness........................................................................................... 20

Setting the date................................................................................................................. 20

Selecting program packages ............................................................................................ 21

Completing the initial commissioning process.................................................................. 21

Drying ............................................................................................................................... 23

1. Notes on correct laundry care....................................................................................... 23

Washing before drying .................................................................................................. 23

Removing foreign objects ............................................................................................. 23

Care symbols ................................................................................................................ 23

2.Loading the tumble dryer .............................................................................................. 24

3. Selecting a program ...................................................................................................... 24

Switching on the tumble dryer ...................................................................................... 24

4. Selecting program settings ........................................................................................... 25

Selecting the drying level .............................................................................................. 25

Selecting extra options ................................................................................................. 25

5.Starting a program ........................................................................................................ 27

Payment system (optional)............................................................................................ 27

Calling up current program parameters ....................................................................... 27

Program runtime/estimated time remaining.................................................................. 27

Program end...................................................................................................................... 28

End of the program ....................................................................................................... 28

Removing the laundry ................................................................................................... 28

Care notes..................................................................................................................... 28

Contents

5

Timer ................................................................................................................................. 29

Prerequisite for setting the timer................................................................................... 29

Setting the timer............................................................................................................ 29

Changing the program sequence .................................................................................. 30

Changing a program once it has started........................................................................... 30

Canceling the current program.......................................................................................... 30

Reselecting a canceled program .................................................................................. 30

Time left............................................................................................................................. 30

Supervisor level ............................................................................................................... 31

Opening the Supervisor level ............................................................................................ 31

Access via code ................................................................................................................ 31

Change code..................................................................................................................... 31

Closing the settings menu................................................................................................. 31

Controls / Display.............................................................................................................. 31

Language ...................................................................................................................... 31

Language entry ............................................................................................................. 31

Set languages ............................................................................................................... 32

Display brightness......................................................................................................... 32

Clock display................................................................................................................. 32

Date............................................................................................................................... 32

Volume .......................................................................................................................... 33

Res. moisture display.................................................................................................... 33

Visibility parameters ...................................................................................................... 33

Display off status .......................................................................................................... 33

Machine off status......................................................................................................... 34

Delay start ..................................................................................................................... 34

Memory ......................................................................................................................... 34

Temperature unit ........................................................................................................... 34

Weight unit .................................................................................................................... 34

Change code................................................................................................................. 35

Program selection ............................................................................................................. 35

Controls......................................................................................................................... 35

Program packages ........................................................................................................ 36

Favorite programs ......................................................................................................... 36

Special programs .......................................................................................................... 36

Sort programs ............................................................................................................... 38

Program color allocation ............................................................................................... 38

Process technology........................................................................................................... 38

Anti-crease.................................................................................................................... 38

Drying levels.................................................................................................................. 38

Additional cooling ......................................................................................................... 39

Cooling down temperature............................................................................................ 39

Service............................................................................................................................... 39

Clean out the airways.................................................................................................... 39

Clean the filters ............................................................................................................. 39

Service interval.............................................................................................................. 40

Contents

6

External applications ......................................................................................................... 41

External exhaust flap..................................................................................................... 41

Additional fan ................................................................................................................ 41

Pressure sensor ............................................................................................................ 41

Peak load signal ............................................................................................................ 41

Peak load prevention .................................................................................................... 42

Select KOM module ...................................................................................................... 42

Availability of Miele digital products.............................................................................. 42

WiFi / LAN ..................................................................................................................... 42

Remote.......................................................................................................................... 43

Remote Update............................................................................................................. 43

Machine parameters.......................................................................................................... 44

Legal Information .......................................................................................................... 44

Cleaning and care ........................................................................................................... 45

Cleaning the lint filter......................................................................................................... 45

Cleaning the drum and the outside of the casing ............................................................. 46

Additional annual cleaning ................................................................................................ 46

Technical Service............................................................................................................. 47

Contact in case of fault ..................................................................................................... 47

Optional accessories......................................................................................................... 47

Installation........................................................................................................................ 48

Installation requirements ................................................................................................... 48

General operating conditions ............................................................................................ 48

Transport ........................................................................................................................... 48

Installing the tumble dryer................................................................................................. 49

Securing the machine........................................................................................................ 50

Electrical connection ......................................................................................................... 50

Supply air, exhaust, and ventilation cross-sections.......................................................... 52

Supply air/exhaust air ................................................................................................... 52

Calculating the total length and diameter of a supply-air or exhaust pipe ................... 52

Substitute duct lengths................................................................................................. 52

Maximum permissible total ducting length................................................................... 53

Room ventilation opening for air intake from the setup room....................................... 54

Exhaust connection ...................................................................................................... 55

Steam connection (only for steam-heated variants).......................................................... 61

Hot water connection (only for hot water-heated variants) ............................................... 61

Gas connection (only for gas-heated variants).................................................................. 61

Gas................................................................................................................................ 62

Steam ................................................................................................................................ 70

Operating pressure values ............................................................................................ 70

Fitting information for steam and condensate hoses.................................................... 71

Heater bank information................................................................................................ 71

Steam valve for high-pressure steam – indirect............................................................ 71

Hot water........................................................................................................................... 72

Operating conditions..................................................................................................... 72

Heater bank information................................................................................................ 72

Contents

7

Networking....................................................................................................................... 74

Pairing instructions............................................................................................................ 74

Opening the supervisor level......................................................................................... 74

Establishing the network connection via WPS ............................................................. 74

Establishing the network connection via soft AP.......................................................... 74

Establishing the network connection using a LAN cable.............................................. 74

Optional accessories ...................................................................................................... 77

Communication box .......................................................................................................... 77

XKM3200WLPLT ............................................................................................................ 77

Original spare parts and accessories................................................................................ 78

Technical data.................................................................................................................. 79

IMPORTANT SAFETY INSTRUCTIONS

8

 It is essential to read these instructions.

This tumble dryer complies with all current local and national safety requirements. Inap-

propriate use can, however, lead to personal injury and material damage.

Read the Operating Instructions carefully before using the tumble dryer. They contain im-

portant information on safety, installation, use, and maintenance. This prevents both per-

sonal injury and damage to the tumble dryer.

In accordance with standard UL60335-1, CAN/CSA-C22.2 No.60335-1, IEC60335-1,

Miele expressly and strongly advises that you read and follow the instructions in the

chapter on installing the tumble dryer as well as the IMPORTANT SAFETY INSTRUC-

TIONS.

Miele cannot be held liable for injury or damage caused by non-compliance with these

instructions.

Keep these Operating Instructions in a safe place and pass them on to any future user.

When instructing other people how to use the tumble dryer, they must be made aware of

these IMPORTANT SAFETY INSTRUCTIONS.

Appropriate use

 The tumble dryer is designed for industrial use only.

 The tumble dryer is intended exclusively for drying textiles washed in water which have

been labeled as suitable for tumble drying by the manufacturer on the care label. Any other

applications may be dangerous. Miele cannot be held liable for damage resulting from in-

correct or improper use or operation.

 This tumble dryer is not intended for outdoor use.

 Do not install the tumble dryer in a room where there is a risk of frost. At temperatures

around freezing point, the tumble dryer may not be able to operate properly. The permitted

room temperature is between 40°F and 95°F (2°C and 40°C).

 If the machine is operated in the commercial sector, it may only be operated by trained

or qualified personnel. If the machine is operated in an unsecured location, the supervisor

must ensure that its use does not pose a risk.

 The tumble dryer should only be used by people with reduced physical, sensory, or

mental capabilities, or lack of experience or knowledge, if they are supervised while using

it or have been shown how to use it in a safe way and understand and recognize the con-

sequences of incorrect operation.

 Children must be kept away from the tumble dryer unless they are constantly super-

vised.

 Children should be supervised in the vicinity of the tumble dryer. Never allow children to

play with the tumble dryer.

 Uses other than those listed above are not recommended and shall release the manu-

facturer from liability.

IMPORTANT SAFETY INSTRUCTIONS

9

Preventing misuse

 Do not make any alterations to the tumble dryer, unless authorized to do so by Miele.

 Do not lean on the dryer door. Otherwise, the tumble dryer may tip over, causing injury

to yourself or others.

 Do not use a pressure washer or hose to clean the tumble dryer.

 To ensure the correct performance of the tumble dryer and to prevent malfunctions and

fire hazards, it is important to carry out maintenance on a regular basis.

 Do not store or use gasoline, petrol, paraffin, or other highly flammable liquids near the

tumble dryer. Risk of fire and explosion.

 Do not expose the tumble dryer to air which contains chlorine, fluorine, or other solvent

vapors. This contaminated air can cause a fire.

 To prevent the risk of fire, the following items must not be dried in the tumble dryer:

- Items which have not been washed.

- Items which have not been thoroughly cleaned and are still soiled with grease, oil, or

other deposits (such as kitchen linens or cosmetics cloths with cooking oils, grease, lo-

tions, etc). If items have not been thoroughly cleaned, there is a danger that they might

ignite when heated, even after they have been removed from the tumble dryer at the

end of the program.

- Items (e.g., mops and floor cloths) that have been treated with inflammable cleaning

agents or which contain residues of acetone, alcohol, benzene, petrol, kerosene, stain

remover, turpentine, wax and wax remover, or other chemicals.

- Items which have been soiled with hair lacquer, hair spray, nail polish remover, or similar

substances.

Wash heavily soiled items thoroughly by increasing the amount of detergent and selecting

a high washing temperature. If in doubt, wash the items several times.

 Warning: Never switch the tumble dryer off before the end of the drying program. If you

absolutely must interrupt the program, remove all items immediately and spread them out

to cool down.

 Never operate the tumble dryer without the lint filter or with a damaged lint filter. This

could lead to malfunctions. Lint can clog the air passages, heating elements, and ducting,

which could result in a fire. In this case, stop the tumble dryer immediately and replace the

damaged lint filter.

Technical safety

 Before installing the dryer, check it for visible signs of damage.

Do not install or use a damaged machine.

 Do not connect the dryer to the electrical supply by an extension cord (risk of fire due to

overheating).

 Fire hazard due to controllable socket. This tumble dryer must not be connected to a

controllable socket (e.g., a timer). There is a risk of the laundry self-igniting if the tumble

dryer’s cooling phase is interrupted.

IMPORTANT SAFETY INSTRUCTIONS

10

 The electrical safety of this dryer can only be guaranteed when continuity is complete

between it and an effective grounding system. It is essential that this standard safety re-

quirement is observed and regularly tested. If in any doubt, please have the electrical in-

stallation inspected by a qualified electrician. Miele cannot assume responsibility for the

consequences of an inadequate grounding system.

 Unauthorized repairs could result in unforeseen dangers for the user, for which Miele

cannot accept liability. Repairs should only be carried out by a Miele authorized technician,

otherwise any subsequent damage may not be covered by the warranty. Repair instruc-

tions can be requested from Miele.

 Faulty components should only be replaced by Miele original parts. Miele may only

guarantee the safety standards of the machine when Miele replacement parts are used.

 In the event of a fault and for cleaning and care purposes, the tumble dryer must be dis-

connected from the power supply. The tumble dryer is only disconnected from the power

supply, if:

- the plug is withdrawn, or

- the breakers are disconnected, or

- the breakers have been completely removed.

 The tumble dryer may not be used in mobile installations (e.g., on ships).

 Follow the instructions in “Installation” and “Technical data”.

 The tumble dryer may only be operated when the ducting has been installed and the

room is sufficiently ventilated in accordance with all local codes.

 The ducting must never be installed in any of the following flues or shafts:

- Chimneys or smokestacks that are in use.

- Shafts that are used to ventilate installation rooms with fireplaces.

- Flues that are used by third parties.

Smoke or exhaust gas that is fed back into the flue or shaft may be toxic.

 Regularly check all components in the ducting (e.g., wall pipe, external grille, bends, el-

bows, etc.) to make sure that air can move through them and to ensure that they are work-

ing properly. Clean components when necessary. Lint deposits in the ducting system will

prevent the air from being extracted properly and, as a result, will stop the tumble dryer

from working properly.

If existing ducting is due to be used, it must be checked before being installed in the tum-

ble dryer.

Low pressure must not occur in the ducting.

 There is a risk of suffocation and poisoning due to exhaust gases being sucked back if

gas-powered flow heaters, gas-powered room heaters, coal-burning stoves with a flue

connection, etc., are installed in the same room, in the same apartment, or in neighboring

rooms and the negative pressure is 4Pa or more.

The following measures for suitable room ventilation (examples) can help to prevent nega-

tive pressure in the installation area:

- Install vents that cannot be closed in the exterior walls.

IMPORTANT SAFETY INSTRUCTIONS

11

- Use window switches so that the tumble dryer can only be switched on when a window

is open.

Always seek approval from the appropriate authority (gas installer, chimney sweep, etc.) to

confirm that the machine can be operated without risk and that negative pressure of over

4Pa can be prevented.

 If multiple tumble dryers are to be connected to one exhaust air duct, a non-return flap

must be installed directly on the duct for each tumble dryer.

If this requirement is not observed, the tumble dryers may be damaged and their electrical

safety could be affected.

 The electrical plug must be easily accessible so that the tumble dryer can be discon-

nected from the power supply at any time. The operator must be able to check from any

access point that the electrical plug is still removed.

 If the appliance is hard wired, protective measures must be made on site to disconnect

the tumble dryer from the electrical supply.

 Do not block the gap between the bottom of the tumble dryer and the floor with toe-

kicks, deep pile carpet, etc.

 Ensure that no closeable door, sliding door, or an oppositely hinged door is installed that

would hinder the drum door being opened in any way.

 If the power cord is damaged, it should be replaced by a Mieleauthorized technician in

order to protect the user from harm.

 The dryer, when installed, must be electrically grounded in accordance with local codes

or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA70, or the

Canadian Electrical Code, CSAC22.1.

 The dryer must not be installed or stored in an area where it will be exposed to water

and/or weather.

 Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can

cause improper operation.

Dryers with gas heating

 The installation must conform with local codes or, in the absence of local codes, with

the National Fuel Gas Code, ANSIZ223.1/NFPA 54, or the Natural Gas and Propane Instal-

lation Code, CSAB149.1.

 The dryer and its manually operated appliance main gas valve must be disconnected

from the gas supply piping system during any pressure testing of that system at test pres-

sures in excess of 1/2psi (3.5kPa).

 The dryer must be isolated from the gas supply piping system by closing the equipment

shutoff valve during any pressure testing of the gas supply piping system at test pressures

equal to or less than 1/2psi (3.5kPa).

 A minimum 1/8-in NPT plugged tapping, accessible for test gauge connection, must be

installed immediately upstream of the gas supply connection to the dryer.

IMPORTANT SAFETY INSTRUCTIONS

12

Take these safety precautions if you smell gas

- Extinguish all flames immediately.

- Close the on-site gas shut-off device, the gas shut-off device on the gas meter or the

main gas shut-off device immediately.

- Open all windows and doors immediately.

- Do not light any naked flames (e.g., matches or lighters).

- Do not smoke.

- If there is the smell of gas in a room, never enter the room with an open flame.

- Do not carry out any actions that will create electrical sparks (such as pulling out electri-

cal plugs or pressing electrical switches or bells).

- If you cannot find the cause of the gas smell and all gas valves have been shut off,

please call the gas supply company immediately.

If other persons are being shown how to operate the machine, they must be given and/

or made aware of these important safety precautions.

Correct use

 Always close the drum door after each drying cycle. This will prevent:

- Children climbing into the tumble dryer or hiding things in it.

- Pets or other small animals climbing into the tumble dryer.

 Keep the room where the tumble dryer is located free from dust and lint. If the air that is

taken into the machine contains dirt particles, this can cause blockages. A fault may then

occur and there is a risk of fire.

 The lint filter must be cleaned on a regular basis.

 To ensure problem-free operation of the tumble dryer:

- Remove the lint from the lint filter after every drying cycle.

- In addition, the lint filter and the air passages must be cleaned when prompted by the

display.

 Remove all items from the pockets of the laundry to be dried (e.g., lighters, matches,

keys).

 The program finishes when the cooling phase starts. Many programs are followed by a

cooling phase to ensure that the items are not too hot to handle when you remove them

(this also reduces the risk of the laundry self-igniting). Always remove all items of laundry

from the dryer immediately after the cooling phase.

 Fabric softener and similar products must be used according to the instructions on the

manufacturer’s packaging.

 For machine parts made from stainless steel:

Avoid contact between stainless steel surfaces and liquid detergents or disinfecting agents

which contain chlorine or sodium hypochlorite. These agents can cause corrosion on

stainless steel.

Aggressive chlorine bleach vapors can also be corrosive.

Do not store open containers of these agents near the machines.

IMPORTANT SAFETY INSTRUCTIONS

13

Accessories

 Only use genuine Miele spare parts and accessories with this machine. Using parts or

accessories from other manufacturers may invalidate the warranty, and Miele cannot ac-

cept liability.

Miele cannot be held liable for damage caused by failure to comply with these IM-

PORTANT SAFETY INSTRUCTIONS.

Description of the machine

14

①

②

④

⑤⑥

⑦

⑧

⑨

⑩

③

aControl panel with touch display

bDoor

cLint filter flap

d4 height-adjustable screw feet

eElectrical connection

fCommunication module slot

gIntake vents for drying air

hExhaust duct

iConnection for communication box

jCommunication box (optional)

For setting up a connection with external systems

Operating the tumble dryer

15

Control panel

7

asensor button

For selecting the current user language

When the program ends, the language is automatically reset to the language set at the

Supervisor level.

bsensor button

Takes you back one level in a menu.

cTouch display

d/sensor button

For starting the selected drying program and canceling a program once it has started.

The program selected can be started as soon as the sensor button starts flashing.

eOptical interface

For Miele Service

fbutton

For switching the tumble dryer on and off. The tumble dryer switches off automatically

to save energy. It is switched off an adjustable time after the end of the program/Anti-

crease phase, or after being switched on if no further selection is made.

gEmergency shut-off

It should only be activated in the event of danger or in order to prevent danger. When

this switch is activated, the machine is immediately switched off and put in a safe condi-

tion. Once the danger has been averted, the switch can be unlocked again by turning

the knurled dial to the right.

Operating the tumble dryer

16

Sensor buttons and touch display with sensor buttons

The,, andStart/Stopsensor buttons and the sensor buttons in the display react

to finger-tip contact. Every tap of a sensor button is confirmed with an audible keypad

tone. You can adjust the volume of the keypad tone or switch it off (see “Supervisor level”).

The control field with sensor buttons and the touch display can be scratched by pointed

or sharp objects, e.g., pens.

Only touch the control field with your fingers.

Main menu

After switching on the tumble dryer, the main menu will appear in the display. You can ac-

cess all the important sub-menus from the main menu.

Touch the sensor button at any time to return to the main menu. Values set previously

are not saved.

11:02



Programs



Favorites



Supervisor

Help

Main menu

“Programs” menu

In this menu, you can select the drying programs.

“Favorites” menu

In this menu, you can select 1favorite program from a total of 12favorite programs. The

drying programs can be set up and saved by the supervisor in the Favorites menu (see “Fa-

vorite programs” under “Supervisor level”).

“Supervisor” menu

You can alter the tumble dryer’s electronic to suit changing requirements in the supervisor

level (see “Supervisor level”).

Operating examples

Option lists

Scrolling through the “Programs” menu (single selection)

 11:02

Cottons

Programs

Cottons PRO Minimum iron Delicates

Cottons  Woolens

Operating the tumble dryer

17

To scroll through the menu, place your finger on the touch display and move it left or

right.

The orange scroll bar in the bottom display area shows that there are further options to

choose from.

To select the required drying program, touch the program name with your finger.

The display will now change to the standard menu for that program.

“Extras” menu (multiple selection)

11:02

Gentle tumble

Extras



OK



Anti-crease



To select one or more Options, touch the required Options with your finger.

Currently selected Options are highlighted orange. To deselect an option, simply touch the

option again.

Setting numerical values

You can set numerical values in some menus. You can set the numerical values by swip-

ing your finger up and down on the display.

10

11

13

14

12 00

59

58

01

02



Clock display

OK

Place your finger on the number that you want to change.

To set the required number, swipe your finger up or down on the display.

Confirm the set numerical value by touching the OKsensor button.

Tip: For some settings, depending on the value range and increments, the value can also

be set using a numerical keypad. Briefly touching the numbers will bring up the numerical

keypad. Once a valid number has been entered, the OKsensor button will be highlighted

green.

12 00

11 59

10 58

13 01

14 02



Clock display

OK

Briefly touch a number between the two lines with your finger.

Operating the tumble dryer

18

The numeric block will flash.

12:00

3

4

21

5 6

7



8

0

9

Clock display

OK

To enter the numerical value, touch the numbers on the right-hand side and then confirm

with OK.

Pull-down menu

The pull-down menu can be used to display information (e.g., about a drying program).

11:02

Time left h

2:27



Status

Cottons Drying



If an orange bar appears at the top of the screen in the middle of the display, you can open

the pull-down menu. Touch the bar and drag down with your finger.

To close the pull-down menu again, touch the orange bar and drag it upward with your fin-

ger.

Exiting the menu

Tap the sensor button to return to the previous screen.

Entries made before this which have not been confirmed withOK will not be saved.

Help display

With some menus, Help appears along the bottom line of the display.

If you need more information about the current menu, touch the Helpsensor button.

The additional information is shown in the display.

Touch the sensor button to return to the previous screen.

Before using for the first time

19

Risk of injury or damage to property due to improper installa-

tion.

Incorrect installation of the tumble dryer can lead to personal injury

or damage to property.

Before using the tumble dryer for the first time, make sure it has

been installed

and connected correctly.

See the information in the section on “Installation”.

Complete the initial commissioning process. During the initial com-

missioning process, you will need to define the settings for daily use

of the tumble dryer. Some settings can only be modified during the

initial commissioning process. After that, they can only be changed

by Miele Service.

These settings are also described under “Supervisor level”.

Switching on the tumble dryer

Press the button.

The welcome screen will light up.

Setting the display language

You will be asked to select the display language. You can change the

language at any time (see “Language” under “Supervisor level”).

deutsch

english

(AU)

english

(CA) español

english

(GB)

Language

OK

français

(F)

Swipe left or right across the display with your finger until the lan-

guage you want appears.

Briefly touch the required language with your finger.

The selected language will be highlighted in orange and the display

will change to the next setting.

Reference to optional external machines

If there are external devices (e.g., peak-load systems), connect the

communication box and/or slide a communication module into the

slot on the back of the tumble dryer before initial commissioning. For

this purpose, the tumble dryer must be disconnected from the

power supply. Then start the commissioning process.

Before using for the first time

20

A reference to optional external hardware appears. Confirm the infor-

mation with the OK sensor control.

Setting the display brightness

You will be asked to select the brightness of the display.

Darker Brighter

Display brightness

OK

Touch the segment bar for the required level of brightness.

The selected level of brightness is represented by the length of the

segment bar.

Confirm with the OKsensor button.

The display will change to the next setting.

Setting the date

22

21

19

18

2022

2021

202020

2019

2018

Date

OK

September

August

July

June

May

Place your finger on the value that you want to change and move

your finger upward or downward.

Once all values have been selected, confirm your entry with the

OKsensor button.

The display will now change to the next setting.

Setting the time

10

11

13

14

12 00

59

58

01

02



Clock display

OK

Place your finger on the number that you want to change and move

your finger upward or downward.

Confirm with the OKsensor button.

The display will change to the next setting.

Page is loading ...

Miele PDR 922 Operating instructions

This manual is also suitable for

Miele PDR 922 Operating instructions

Related papers

Other documents