© 2005 Alamo Group Inc.
RHINO®
1020 S. Sangamon Ave.
Gibson City, IL 60936
800-446-5158
Email: [email protected]
PART'S MANUAL
An Operator's Manual was shipped with the equipment in the
Manual Canister. This Operator's Manual is an integral part of
the safe operation of this machine and must be maintained
with the unit at all times. READ, UNDERSTAND, and FOLLOW
the Safety and Operation Instructions contained in this manual
before operating the equipment. If the Operator's Manual is
not with the equipment, contact your dealer or Servis-Rhino
(800-446-5158) to obtain a Free copy before operating the
equipment.
FM60A/72A
Rear Discharge
60A & 72A Rotary Mowers
Rev 11-12 Effective S/N FM60A-14000 to Current Part No. 00778236P
FM72A-15800 to Current
TO THE OWNER/OPERATOR/DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic
failure with possible injury or death.
Parts Section – 2
©2005 Alamo Group Inc.
For maximum safety and to guarantee optimum product reliability, always use
genuine Servis-Rhino Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help
locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization
ordering the parts, who should be charged, and if possible, the serial number of the machine
for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a
Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE: Please refer to The Safety Section in the front of this Manual for the proper
Part Number when ordering Replacement Safety Decals.
PARTS ORDERING GUIDE
RHINO®
1020 S. Sangamon Ave.
Gibson City, IL 60936
800-446-5158
Email: [email protected]
PART NAME INDEX
BELT ASSEMBLY 60" .......................................................................................................................................................... 14
BELT ASSEMBLY 72" .......................................................................................................................................................... 15
BLADE AND SPINDLE ASSEMBLY ..................................................................................................................... 9
CASTER WHEEL ASSEMBLY .......................................................................................................................... 12
DRIVELINE ASSEMBLY......................................................................................................................................................... 5
GEARBOX ASSEMBLY.......................................................................................................................................................... 6
OPTIONAL QUICK ATTACH HITCH KIT Rev 07-04 ........................................................................................................... 16
ROLLER- FRONT (EXTRA EQUIPMENT)........................................................................................................................... 11
SAFETY DECAL SHEETS ................................................................................................................................................... 17
SHIELD ASSEMBLY Rev 09-05............................................................................................................................................. 8
SPINDLE ASSEMBLY .......................................................................................................................................................... 10
3-POINT LIFT ASSEMBLY..................................................................................................................................................... 4
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 3
3-POINT LIFT ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION
1 00757949 1 BAR TOP LINK BD80
2 00768320 4 BAR, HITCH
3 00769453 2 BAR-A-FRAME
4 00769549 2 BAR-REAR LIFT STRAP FM60A
00768319 2 BAR, REAR LIFT STRAP FM72A
5 00761724 4 BUSHING HITCH
6 00762082 6 BUSHING HITCH
7 00757953 1 BUSHING 1-1/4X7/32X3 A-FRAME
8 00603500 2 PIN, HITCH CAT I
9 37107B12 1 PIN TOP LINK CAT 1(PLATED)
10 37107B13 1 CLIP-X HAIR PIN
11 00037200 3 LOCKNUT
12 00748598 1 HEXB 3/4-10UNC 5-1/2 PL5
13 02929200 2 HHCS 3/4-10UNC 1-1/2 PL5
14 2196 2 CLIP (LYNCH PIN), 13/32 DIA.
15 02793900 4 HHCS 7/8-9UNC 2-1/2 GR 5
16 5JRC1490 4 NUT TOPLOCK 7/8 NC PLB
17 00750952 2 HEXB,5/8NC X 2-1/2,ZP,GRD5
18 00695100 4 LOCKNUT
19 00001400 4 FLATWASHER
20 00008300 2 BOLT
21 00778212 1 WDMT,DECK - FM60A
00778203 1 WDMT,DECK - FM72A
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 4
DRIVELINE ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION
00768041A - DRIVELINE
1 00764500A 2 COMPLETE COLLAR YOKE
2 00756231 2 CROSS & BEARING KIT SERIES 40
3 00759169 1 PIN ROLL 8mm X 60mm
4 00759165 1 PIN ROLL INNER TUBE
5 00764506 1 COLLAR-GUARD-RETAINER
6 00754330 6 BOLT, NYLON - SAFETY SHIELD]
7 00764507 1 COLLAR-GUARD-RETAINER
8 00768168 1 SHIELD, ASY, CMPLT
9 00768165 1 DRIVELINE, HALF ASY, OUTER
10 00768164 1 DRIVELINE, ASY, INNER HALF
11 00774079 2 KIT,SLIDE COLLAR REPAIR
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 5
GEARBOX ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION
00777688 - ASY,GEARBOX
1 00778239 1 HOUSING GEARBOX
2 2716532 2 SNAP RING
3 2716540 1 CAP PLUG
4 00564800 1 BEARING, BALL
5 00754761 2 SHIM
6 2716564 1 SHIM KIT
7 00755615 2 BEARING
8 2716656 1 LOCKNUT
9 00778240 1 SEAL OUTPUT
10 00778241 1 SHAFT INPUT
11 00763206 1 SEAL, INPUT SHAFT
12 00754757 1 BEARING
13 00778242 1 COVER GEARBOX
14 00778243 1 SHIM
15 00755633 1 PLUG,3/8"
16 00756649 1 SNAP RING
17 00778244 1 GEAR ,CROWN
18 00772980 1 PLATE
19 00771879 1 SHIM
20 00778245 1 SHAFT, PINION
21 00778246 1 WASHER, EXTERNAL TOOTH
22 4840 1 NUT, CASTLE
23 00771856 4 BOLT METRIC
24 00778187 1 PLUG,BREATHER DIPSTICK
25 70497 1 COTTER PIN
00765444 1qt QT,ALAMO 000 GEAR LUBE
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 7
SHIELD ASSEMBLY Rev 09-05
ITEM PART NO. QTY. DESCRIPTION
1 00774843 1 PLATE GEARBOX MOUNT
2 00777538 1 SHIELD,RH MOLDED BELT FM60A
00777540 1 SHIELD,RH MOLDED BELT FM72A
3 00777539 1 SHIELD,LH MOLDED BELT FM60A
00777541 1 SHIELD,LH MOLDED BELT FM72A
4 00769933 1 NUT-PLASTIC KNOB 3/8 NC PL
5 00748823 2 HHCS 1/2-13UNC 1-1/2 PL5
6 00777688 1 ASY,GEARBOX
7 00001800 8 LOCKNUT
8 00002700 4 FLATWASHER
9 26168 6 CRG-BLT 3/8 X 1 GR5
10 00695100 4 LOCKNUT
11 00008300 4 BOLT
12 00769451 1 PLATE-GEARBOX SLIDE
13 02886900 4 CARR 1/2-13UNC 1-1/2 PL5
14 00769446 1 PLATE-GEARBOX ADJUSTMENT
15 00013901 2 NUT
16 00769898 1 BOLT 3/8 NC 4-1/2 PL2
17 02961255 6 PUSHNUT, BOLT RETAINER, 3/8
18 00758582 1 SHIELD,IMPLEMENT
19 00011700 4 LOCKWASHER
20 00023500 4 FLATWASHER
21 02958784 4 BOLT METRIC 8-P1.25- 20MM PL5
22 02030700 4 HHCS 1/2-13UNC 1-1/4 PL5
23 00011100 1 FLATWASHER 3/8 PL STD
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 8
BLADE AND SPINDLE ASSEMBLY Rev 07-05
ITEM PART NO. QTY. DESCRIPTION
1 00778152 3 FM60A STD BLADE 2 1/2 X 1/4 X 20 7/16 CCW
00766811 3 FM60 OPT HD BLADE 3 X 3/8 X 20 7/16 CCW
00778178 3 FM72A STD BLADE 2 1/2 X 1/4 X 24 1/2 CCW
00765445 3 FM72A OPT HD BLADE 3 X 3/8 X 24 1/2 CCW
2 00766480 3 BOLT,BLADE 5/8-18 X 1-1/2 LH
3 00756077 3 WASHER,5/8 HARDENED
4 00753642 12 HHCS,3/8NC X 1-1/4,ZP,GRD5
5 03101646 12 LOCKWASHER,3/8,MEDIUM-ZP
6 00777699 3 ASY,SPINDLE
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 9
00778223 3 FM72A OPT UPDRAFT BLADE 2-1/4 X 1/4 X 24-1/4 CCW
SPINDLE ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION
00777699 - ASY,SPINDLE HOUSING
1 00776434 1 SPINDLE,SHAFT
2 00765411 1 SEAL,PROTECTOR
3 00778161 1 HOUSING, SPINDLE
4 00777723 1 NUT,SPECIAL ADJUSTING
5 5312314 2 BEARING CONE LM48548
6 70044 2 BEARING CUP LM48510
7 00766549 2 SEAL
8 15B1200 1 WASHER
9 00777722 1 NUT,HEX TOPLOCK JAM
10 00003500 1 ZERK FITTING 1/8 STRAIGHT
11 00765813 1 KEY-SQ 1/4 X 3/4 LG
12 02957080 1 SETSCREW
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 10
ROLLER- FRONT (EXTRA EQUIPMENT)
ITEM PART NO. QTY. DESCRIPTION
1 00001400 2 FLATWASHER
2 00002000 4 BOLT
3 00755153 1 PIN-COTTER 3/16 X 1-1/2 PLATED
4 4528 4 NUT, LOCK 3/8-16 FLG WHIZ
5 4860 1 WLDMT, AXLE
6 00765317 1 PLATE-BRACKET-LH
7 00765316 1 PLATE-BRACKET-RH
8 4909 1 ROLLER-FRONT
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 11
CASTER WHEEL ASSEMBLY Rev 08-05
ITEM PART NO. QTY. DESCRIPTION
1 00761503 8 SPACER 1-1/2 OD X1ID X 1/2LG
2 00766954 4 FORK
3 00778248 4 ASSY- SOLID TIRE WHL
00778247 4 ASSY- PNEUMATIC TIRE WHL (OPTIONAL)
3A 00767637 8 BUSHING-1 FOR WHL #00769862
4 00002700 4 FLATWASHER
5 00778145 4 AXLE PIN
6 00774839 2 AXLE ARM FM60A/FM72A
7 00767637 8 BUSHING-1 FOR WHL #00769862
8 00761504 16 SPACER 1-1/2 OD X 1ID X1LG
9 4805 4 PIN, SNAPPER 1/4 X 2
10 00761453 8 BEARING FLANGE
11 4720 4 GREASE FITTING 1/8 SELF TAP
12 02957009 4 HHCS 3/8 NC 3-1/2 PL5
13 00761961 8 WASHER FM60A
00761961 8 WASHER FM72A
13A 00774848 2 BACKING PLATE (FM72A ONLY)
14 4528 4 NUT, LOCK 3/8-16 FLG WHIZ
15 00765338 8 SPACER 1-1/2OD X 1ID X 1/4LG
16 00763662A 4 TIRE/WHEEL/COMP. (PNEUMATIC)
00769862 4 SOLID TIRE COMPT 10X3.25 RIB
16A 00763703 4 BEARING-ROLLER-1
16B 00763704 4 BEARING-END-CAP-PLAIN
16C 00763705 4 BEARING-END-CAP-NOTCHED
17 00750959 4 HEXB,1/2NC X 1,ZP,GRD5
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 13
BELT ASSEMBLY 60"
ITEM PART NO. QTY. DESCRIPTION
1 00778151 3 SHEAVE,DBL GR,5.0 OD
2 00778150 1 SHEAVE,DBL GR,10.55 OD
3 00777722 3 NUT,HEX TOPLOCK JAM 3/4-10 PLB
4 15B1200 3 WASHER 3/4 P SAE
5 00765813 4 KEY-SQ 1/4 X 3/4 LG
6 00778228 1 BELT (MATCHED SET OF 2)
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 14
BELT ASSEMBLY 72"
ITEM PART NO. QTY. DESCRIPTION
1 00777382 3 SHEAVE,DBL GR,5.9 OD
2 00778150 1 SHEAVE,DBL GR,10.55 OD
3 00777722 3 NUT,HEX TOPLOCK JAM 3/4-10 PLB
4 15B1200 3 WASHER 3/4 P SAE
5 00765813 4 KEY-SQ 1/4 X 3/4 LG
6 00778229 1 BELT (MATCHED SET OF 2)
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 15
OPTIONAL QUICK ATTACH HITCH KIT Rev 07-04
ITEM PART NO. QTY. DESCRIPTION
00777570 - KIT, QUICK ATTACH HITCH
1 00757949 1 TOP LINK
3 00768320 4 BAR, HITCH
4 00769453 2 BAR-A-FRAME
5 00769549 2 BAR-REAR LIFT STRAP
7 00762082 6 BUSHING HITCH
8 00603500 2 ASY,CAT.1 HITCH PIN W/LW & NUT
9 37107B12 1 PIN TOP LINK CAT 1(PLATED)
10 37107B13 1 CLIP-X HAIR PIN
12 00777564 2* BUSHING LOWER OUTSIDE HITCH PIN
13 00777563 2* BAR, FRONT HITCH
14 00777566 1* BUSHING, UPPER INSIDE HITCH PIN
15 00777567 1* BUSHING, UPPER OUTER HITCH PIN
16 00777569 2* BAR, TOGGLE
17 00777565 4* BUSHING, REAR TOGGLE
18 00002701 2* FLATWASHER,3/4,TYPE AW,ZP
19 00002700 10* FLATWASHER 1/2 PL STD
20 00749130 4* HHCS 1/2-13UNC 1-3/4 PL5
21 314018H5C 1* HEX CAP 1/2-13 X 4 1/2 GR.5
22 00001800 5* LOCKNUT TLM 1/2 NC PLB
23 00777568 2* SPACER, 2.50 OD X 1.69 ID X 1/4"
24 2196 2 CLIP (LYNCH PIN), 13/32 DIA.
* INCLUDED IN KIT # 00777570
NOTE: Hitch frame bars must be in position as shown for hitch to work properly
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 16
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
