Senseon 5EL Installation guide

Brand: Senseon

Model: 5EL

Category: Security door controllers

Type: Installation guide

Model 5EL

Black (C)

0.48" [12mm]

1.72" [44mm]

3.63" [92mm]

Horizontal or vertical (left or right)

#6 square drive pan head (included)

Lock Finish:

Height:

Width:

Length:

Mounting:

Mounting Hardware:

ø.170x.295 [4.3x7.3] (2X)

.42 [10.67]

.625 [16]

1.25 [32]

1.72 [43.7]

.48 [12.19] 1.0 [25.4]

3.63 [92]

Manual

Override

Striker

ø.170 [4.3] (2X)

Inch/mm

Mounting Options

Electronic Lock for Casework

Sliding Doors.

Features:

Lock Voltage Supply:

Lock Connector:

The 5EL is an electronic locking mechanism

with manual override

Withstands up to 150 pounds of force

Works with Senseon Secure Access Control

+6 VDC to +24 VDC

SM08B GHS TB

Striker orientation based on door closure direction for optional lock mounting positions.

Door closure

LH Horizontal

RH Horizontal

Door closure Door closure

RH Vertical

LH Vertical

Horizontal Mounting (standard) Vertical Mounting

Specifications

WARNING! Before installing the lock, you must have access to

manual override lever or the activation device must be connected.

Otherwise, the lock will not unlock and open.

Locate critical dimensions and minimum distance for 5EL assembly (Fig 1)

Installation Guide -- Horizontal installation

Door

Pre-drill 2 mounting holes

3/32" [2mm] drill

The slotted holes will allow for gap adjustment.

1/8" to 3/16" door gap

[3 to 5mm]

1/16" [1.59]

15/16" [23.5]

1/4" [6.4]

min.

1/4" x 5/8" [6 x 16]

Pre-drill hole for cable

and for manual override

Use slots to

locate position

then secure

using round holes

Figure 1

Transferring striker location to drill door (Fig 2)

Detail J

Scale 1:2

Far side door

Detail H

Scale 1:1

Locate the centerpoint of the lock and

transfer this dimension to the door.

Drill the 9/16" diameter hole into the door

frame and install the bushing.

Door strike guide

Figure 2

Model 5EL

Electronic Lock for Casework

Sliding Doors.

Leveling striker in case 5EL assembly is below door track (Fig 4)

Spacer plate

used with

surface

mounted track

Cosmetic cover

available in:

– White

Securing 5EL assembly and optional cosmetic cover (Fig 5)

Figure 4 Figure 5

Striker orientation for right or left hand installation (Fig 3).

Strike direction can be changed

for optional lock positions.

Pull the striker out of the locking mechanism.

Rotate the striker to the desired orientation

and reverse the removal process.

Remove the

retaining screw.

.050 Hex Wrench

Figure 3

Installation Guide -- Horizontal installation (continued)

Model 5EL

Electronic Lock for Casework

Sliding Doors.

Figure 6

Figure 6A

Installation Guide -- Horizontal installation (continued)

Model 5EL

Electronic Lock for Casework

Sliding Doors.

This option provides a secondary bottom

panel cut to fit the interior cabinet.

Minimum panel thickness: 5/8"

A pocket is routed out for lock clearance

on the bottom side of the panel to

conceal the locks.

1/2" [13]

Deep

Based on lock

location to the

inside wall

Detail G

R 10

[R 2.54]

1 7/8" [48]

Detail F

1/2 min.

Center point

of the lock

3 5/8" [92]

minimum

Critical dimensions for optional secondary bottom panel installation (Fig 6)

Technical Data

WIRING SCHEMATIC

Connector

PWR (+6VDC TO +24VDC)

PWR (-) Ground

Trigger : See Note 2

For internal use only, do not use*

Not used

For internal use only, do not use*

Lock Status

PWR (+6VDC TO +24VDC)

PWR (-) Ground

Trigger : See Note 2

For internal use only, do not use*

Not used

For internal use only, do not use*

Lock Status

Example of lock status connection using LED.

Pin 1 maximum rating 30VDC@500mA

Technical Data

Voltage Supply : +6VDC to +24VDC

Current Consumption : 375 mA/350 mS@12VDC

(Unlocking/Locking)

Micro-Switch Specifications

Mechanical Life : 500,000 cycles

(Lock Contact “LC’)

Notes

1. Lock status output:

Lock is unlocked : = “ground”

Lock is locked : = “open”

2. +6VDC to +24VDC at pin 6 will unlock the

Electronic Lock. The Electronic Lock will

remain unlocked until +VDC is removed.

3. (*) Used for Senseon Access Control, do not use.

V (+6 to +24VDC)

“LC”

Circuit

Controller

Model 5EL

Electronic Lock for Casework

Sliding Doors.

ACCURIDE INTERNATIONAL INC.

12311 Shoemaker Avenue

Santa Fe Springs, CA 90670

TEL (562) 903-0200

FAX (562) 903-0208

www.accuride.com

Manufacturing, Engineering, and Sales

United States • Germany • Japan • Mexico • United Kingdom • China

Packaging

D Pack: One 5EL lock assembly per box.

Assembly includes

1 each SDEL-01 (showcase/display case lock)

1 each spacer plate

4 each installation screws

1 each door bushing

1 each door strike guide

1 each cosmetic cover [white]

20 each C 5EL D

Required Kits

Proximity Kit:

One proximity kit per each Senseon system.

Part number SEPROX-US-Kit1. The kit includes:

1 RFID Reader 1 Top link Cable

1 Power Supply 1 AC Cord

1 Reader Holder 1 Proximity Kit Box

1 DC Power Cable 2 Power Supply Holders

12 Cable Clips

Hub Kit: One Hub Kit per cabinet opening (drawer and door).

Modular wiring kit part number SEHUBX-Kit1. The kit includes:

1 Hub Assembly

2 Hub to Lock Cable

4 Cable Clips

6" Double Stick Tape

Optional Kits

Linking Cables: To connect multiple banks for lock openings.

Senseon 5EL Installation guide

Brand: Senseon

Model: 5EL

Category: Security door controllers

Type: Installation guide

Download PDF

report

Senseon 5EL Installation guide

Senseon 5EL Installation guide

Other documents