EM2GO EM022AC1RA Operating instructions

Brand
EM2GO
Model
EM022AC1RA
Type
Operating instructions

EM2GO EM022AC1RA is a 22 kW EV charger with an RFID card reader that allows the charger to be turned on and off. The built-in current control allows you to adjust the output current by limiting the current draw. The output current can be set to 10, 16, 20, 24, and 32A.

Here are some of the features and possible use cases of the EM2GO EM022AC1RA:

  • RFID card reader: The RFID card reader allows you to turn the charger on and off without having to use a key or switch. This is convenient if you want to be able to charge your car without having to get out of the car.
  • Current control: The current control allows you to adjust the output current of the charger. This is useful if you want to limit the amount of current that is drawn from the electrical grid.

EM2GO EM022AC1RA is a 22 kW EV charger with an RFID card reader that allows the charger to be turned on and off. The built-in current control allows you to adjust the output current by limiting the current draw. The output current can be set to 10, 16, 20, 24, and 32A.

Here are some of the features and possible use cases of the EM2GO EM022AC1RA:

  • RFID card reader: The RFID card reader allows you to turn the charger on and off without having to use a key or switch. This is convenient if you want to be able to charge your car without having to get out of the car.
  • Current control: The current control allows you to adjust the output current of the charger. This is useful if you want to limit the amount of current that is drawn from the electrical grid.
em2go
EM022AC1RA | EM022AS0RA
Cable Type (CT) Socket Type (ST)
Das 22 kW EV-Ladegerät verfügt über einen RFID Kartenleser, der das Ein- und Ausschalten
des Ladegerätes ermöglicht.
Die eingebaute Lastregelung ermöglicht die Einstellung des Ausgangsstroms durch
Begrenzung der Stromaufnahme. Der Ausgangsstrom kann auf 10, 16, 20, 24 und 32A
eingestellt werden.
Vorgehensweise
1. Das Ladegerät ist mit einem CEE Stecker 3-Phasig und 32A ausgestattet, verbinden Sie
den CEE Stecker mit einer entsprechenden CEE 3-Phasig 32A Netzsteckdose.
2. Schalten Sie mit Hilfe der RFID-Karte das Ladegerät ein. Durch Drücken des seitlichen
Schalters stellen Sie die Begrenzung der Stromaufnahme ein. Der eingestellte Wert wird
gespeichert.
Bitte beachten Sie, dass Sie den Ladestrom nur schalten können, bevor Sie den Stecker an
das Fahrzeug anschließen.
3. Vor dem Anschließen des Steckers an das Fahrzeug muss das Ladegerät nach der
Einstellung des Stromes ausgeschaltet werden. Schalten Sie durch Vorhalten der
RFID-Karte das Ladegerät aus
4. Jetzt kann das EV Ladegerät mit dem Fahrzeug verbunden werden. Durch Vorhalten
der RFID-Karte schaltet sich das Ladegerät ein und der Ladevorgang beginnt.
5. Wenn der Ladevorgang beendet ist, halten Sie bitte einfach die RFID-Karte vor das Gerät
und das Ladegerät schaltet sich aus.
Die Einstellung des Ausgangsstromes bleibt erhalten, bis sie erneut geändert wird.
em2go ist eine eingetragene Marke der D-Parts Mobilphon & Zubehör GmbH
D-Parts Mobilphon & Zubehör GmbH • Birkenweiher Str. 16 • 63505 Langenselbold, Germany
www.em2go.de
/ www.d-parts.de
em2go
EM022AC1RA | EM022AS0RA
Cable Type (CT) Socket Type (ST)
The 22 kW EV charger has an RFID card reader that allows the charger to be turned
on and o.
The built-in current control allows you to adjust the output current by limiting the
current draw. The output current can be set to 10, 16, 20, 24 and 32A.
Procedure
1. The charger is equipped with a CEE plug 3-phase and 32A, connect the CEE plug to an
appropriate CEE 3-phase 32A mains socket.
2. Turn on the charger with the RFID card. Press the switch on the side to set the current
consumption limit. The set value is saved.
Please note you can only switch the charging current before connecting the plug to the
vehicle.
3. Before connecting the plug to the vehicle, the charger must be switched o after the current
has been set. Turn o the charger by holding the RFID card in front of it.
4. Now the EV charger can be connected to the vehicle. By holding the RFID card in front
of it, the charger will turn on and charging will begin.
5. When the charging is nished, please just hold the RFID card in front of it and the charger
will turn o.
The output current setting will remain until it is changed again.
em2go ist eine eingetragene Marke der D-Parts Mobilphon & Zubehör GmbH
D-Parts Mobilphon & Zubehör GmbH • Birkenweiher Str. 16 • 63505 Langenselbold, Germany
www.em2go.de
/ www.d-parts.de
RFID
  • Page 1 1
  • Page 2 2

EM2GO EM022AC1RA Operating instructions

Brand
EM2GO
Model
EM022AC1RA
Type
Operating instructions

EM2GO EM022AC1RA is a 22 kW EV charger with an RFID card reader that allows the charger to be turned on and off. The built-in current control allows you to adjust the output current by limiting the current draw. The output current can be set to 10, 16, 20, 24, and 32A.

Here are some of the features and possible use cases of the EM2GO EM022AC1RA:

  • RFID card reader: The RFID card reader allows you to turn the charger on and off without having to use a key or switch. This is convenient if you want to be able to charge your car without having to get out of the car.
  • Current control: The current control allows you to adjust the output current of the charger. This is useful if you want to limit the amount of current that is drawn from the electrical grid.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents