TouchTunes 700220-001 Installation And Setup Manual

Brand: TouchTunes

Model: 700220-001

Category: Video converters

Type: Installation And Setup Manual

This manual is also suitable for

CV-509

The TouchTunes 700220-001 HDMI/DVI to Component Converter seamlessly integrates your non-HDMI/DVI display with HDMI or DVI sources, delivering high-definition digital video and audio. Easily connect component-based displays like monitors, TVs, or projectors to HDMI sources with this converter. Experience stunning visuals with support for up to 1080p resolution and enjoy crisp, clear audio through the coaxial S/PDIF or stereo analog audio outputs

HDMI / DVI to Component

CONVERTER

P/N: 700220-001 (CV-509)

Installation and Setu

P/N: 900420-001

Revision 01 − October, 2010

Safety and Notice

The HDMI / DVI to Component Converter [P/N: 700220-001 (CV-509)] has been tested for

conformity to safety regulations and requirements, and has been certified for international

use. However, like all electronic equipments, the HDMI / DVI to Component Converter should

be used with care. Please read and follow the safety instructions to protect yourself from

possible injury and to minimize the risk of damage to the unit.

z Follow all instructions and warnings marked on this unit.

z Do not attempt to service this unit yourself, except where explained in this manual.

z Provide proper ventilation and air circulation and do not use near water.

z Keep objects that might damage the device and assure that the placement of this unit is

on a stable surface.

z Use only the power adapter and power cords and connection cables designed for this

unit.

z Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the

device before cleaning.

Installation and Setu

Chapter 1 Introduction 1

Overview 1

Features 1

Package Contents

Specifications

Chapter 2 Panel Description 3

Chapter 3 Connection Diagram 4

Chapter 4 Hardware Installation 5

Chapter 5 EDID Learning 5

Warranty 5

Table of Contents

Rev.0908

Overview

This HDMI / DVI to Component Converter [P/N: 700220-001 (CV-509)] offers an easy and

instant approach for converting digital HDMI to analog PC video (VGA) and component video

(YPbPr) with digital audio (S/PDIF) and analog stereo audio. With this module, component

based display such as monitors, TV or projectors can be readily connected to HDMI sources.

In addition, the embedded HDMI / DVI selector facilitates the switch between the HDMI and

DVI input sources. This solution lets you keep using your non-HDMI/DVI display to access

HDMI or DVI source, and enjoy high definition digital video and audio.

Features

z HDMI 1.2a & DVI 1.1 compliant

z HDMI video supports up to 1080p

z Support HD (1080i / 720p) component video output

z Support up to UXGA (1600x1200@60) & WUXGA (1920x1200@60) PC graphics output

z Coaxial S/PDIF audio output

z Stereo analog audio output

z Front panel LED indicators and push button

z EDID learning ability

Package Contents

Part Number Description Quantity

P/N: 700220-001 HDMI / DVI to component converter (CV-509) 1

P/N: 300421-072 6ft RCA male-male component video cable (RGB) 1

P/N: 300424-072 VGA-component breakout cable 1

P/N: 900420-001 Installation and Setup Guide 1

P/N: 700229-001 5V 4A in-line power supply unit with power cord 1

Introduction

Specifications

Technical HDMI / DVI to component converter [P/N:700220-001 (CV-509)]

Role of usage D/A converter

HDMI compliance HDMI 1.2a

DVI compliance DVI 1.1

Video bandwidth Single-link 165MHz [4.95Gbps]

Video support Up to 1080p60, WUXGA [1920x1200@60] & UXGA [1600x1200@60]

Audio support Stereo audio

Input TMDS signal 1.2 Volts [peak-to-peak]

Input DDC signal 5 Volts [peak-to-peak, TTL]

Input 1x HDMI

1x DVI

Output

1x VGA or Component (via VGA-component breakout cable)

1x RCA digital audio

1x 3.5mm analog audio

HDMI connector Type A [19-pin female]

DVI connector DVI-I [29-pin female digital only]

VGA connector HD-15 [15-pin D-sub female]

RCA connector Coaxial socket for S/PDIF digital stereo audio [PCM 48kHz]

3.5mm connector Earphone socket for analog stereo audio

Push-in button [1] HDMI / DVI input switch [2] VGA / component output switch

DIP switch 2-pin for EDID learning

Mechanical HDMI / DVI to component converter [P/N:700220-001 (CV-509)]

Housing Metal enclosure

Dimensions

(L x W x H)

Model 128 x 100 x 28mm [5”x 3.9” x 1.1”]

Package 270 x 175 x 80mm [10.6” x 6.9” x 3.1”]

Weight Model 420g [15oz]

Package 795g [1.8 lbs]

Fixedness Wall-mounting case

Power supply 5V 4A DC

Power consumption 6 Watts [max]

Operation temperature 0~40°C [32~104°F]

Storage temperature -20~60°C [-4~140°F]

Relative humidity 20~90% RH [no condensation]

Front Panel

1. DIP Switch for EDID 4. DVI input

2. HDMI or DVI source switch button 5. Power on/off indicator

3. HDMI input 6. +5V DC interlocked power jack

DIP Switch

Pin 1 Mode

ON ª Learn EDID from VGA socket and save EDID to HDMI socket

Pin 2 Mode

ON ª Learn EDID from VGA socket and save EDID to DVI socket

Rear Panel

7. S/PDIF audio output

8. Stereo audio output

9. Component video output via the breakout cable (P/N: 300424-072)

10. VGA or component output switch button

1 3 4

78910

PaNEL DeSCRIPTION

Connection Diagram

1. Connect the HDMI or DVI source either to the dual-view video processor [P/N: 700246-

001 (MX-1003BB)] or the HDMI CAT5e extender [P/N: 700243-001 (CV-57BB)] to the video

input.

2. Connect the S/PDIF or stereo audio source to RCA jack or 3.5mm jack.

3. For connecting to component (YPbPr) TV or projector, link VGA-component breakout

cable (P/N: 300424-072) to the VGA output connector then link a component cable (P/N:

300421-072) to the component (YPbPr) TV or projector.

4. Power up the HDMI / DVI to component converter [P/N: 700220-001 (CV-509)] with the

5V 4A DC power supply unit (P/N: 700229-001) connected.

1. Power up the converter [P/N: 700220-001 (CV-509)]. Connect display to VGA/YPbPr

Output.

2. To learn EDID for HDMI source i.e., the HDMI CAT5e extender [P/N: 700243-001

(CV-57BB)], pull down the DIP switch 1 to ON, the red LED will flash to indicate the EDID

learning process is complete. You DON’T NEED to pull up the DIP switch again unless you

want to learn another EDID by pulling DIP switch 1 up and down.

3. To learn EDID for DVI source i.e., the dual-view video processor [P/N: 700246-001

(MX-1003BB)], pull down the DIP switch 2 to ON, the red LED will flash to indicate the

EDID learning process is complete. You DON’T NEED to pull up the DIP switch again

unless you want to learn another EDID by pulling DIP switch 1 up and down.

Please refer to Barfly Installation and Setup Guide (P/N: 900393-001) and BARFLY

SERVICE SUPPLEMENT for warranty information.

Warranty

EDID Learning

Hard

are Installation

TouchTunes 700220-001 Installation And Setup Manual

Brand: TouchTunes

Model: 700220-001

Category: Video converters

Type: Installation And Setup Manual

This manual is also suitable for

CV-509

Download PDF

report

TouchTunes 700220-001 Installation And Setup Manual

This manual is also suitable for

TouchTunes 700220-001 Installation And Setup Manual

Other documents