Shop fox 1 HP Oscillating Spindle Sander W1686 Owner's manual
- Category
- Power sanders
- Type
- Owner's manual
This manual is also suitable for
Model W1686 Machine Specifications, Page 1 of 2
MODEL W1686
1 HP OSCILLATING SPINDLE SANDER
Product Dimensions
Weight.......................................................................................................... 287 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height........................ 25‐1/4 x 28‐3/4 x 44‐1/2 in.
Footprint (Length x Width).............................................................................. 16 x 16 in.
Shipping Dimensions
Type....................................................................................................... Wood Crate
Content........................................................................................................ Machine
Weight.......................................................................................................... 381 lbs.
Length x Width x Height........................................................................... 26 x 28 x 37 in.
Electrical
Power Requirement.......................................................... 120V or 240V, Single‐Phase, 60 Hz
Prewired Voltage................................................................................................. 120V
Full‐Load Current Rating................................................................ 12A at 120V, 6A at 240V
Minimum Circuit Size................................................................... 15A at 120V, 15A at 240V
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length.............................................................................................. 12 ft.
Power Cord Gauge............................................................................................ 16 AWG
Plug Included....................................................................................................... Yes
Included Plug Type.................................................................................... 5‐15 for 120V
Recommended Plug Type............................................................................. 6‐15 for 240V
Switch Type............................................................ Paddle Safety Switch w/Removable Key
Motors
Main
Horsepower................................................................................................. 1 HP
Phase.............................................................................................. Single‐Phase
Amps..................................................................................................... 12A/6A
Speed.................................................................................................. 1720 RPM
Type......................................................................... TEFC Capacitor‐Start Induction
Power Transfer ................................................................................... Direct Drive
Bearings............................................................... Shielded & Permanently Lubricated
Centrifugal Switch/Contacts Type................................................................. External
Main Specifications
Model W1686 Machine Specifications, Page 2 of 2
Spindle Sander Info
Sanding Drum Diameters................................. 1/4, 3/8, 1/2, 5/8, 3/4, 1, 1‐1/2, 2, 3, 4 in.
Sanding Drum Length............................................................................... 5, 6, 9 in.
Spindle Speed........................................................................................ 1720 RPM
Spindle Oscillation...................................................................................... 72 SPM
Stroke Length......................................................................................... 1‐1/2 in.
Table Length......................................................................................... 25‐1/4 in.
Table Width.......................................................................................... 25‐1/4 in.
Table Thickness....................................................................................... 1‐1/8 in.
Table‐to‐Floor Height.............................................................................. 35‐1/2 in.
Number of Table Inserts...................................................................................... 3
Included Sanding Sleeve Grit Size........................................................................ 100
Table Tilt............................................................................. Front 45, Back 20 deg.
Construction Materials
Base............................................................................................... Formed Steel
Stand.............................................................................................. Formed Steel
Table......................................................................................... Ground Cast Iron
Frame............................................................................................... Sheet Metal
Paint Type/Finish............................................................................. Powder Coated
Other Related Info
Number of Dust Ports......................................................................................... 1
Dust Port Size.............................................................................................. 4 in.
Compatible Mobile Base............................................................................... D2260A
Other
Country of Origin ............................................................................................. Taiwan
Warranty ....................................................................................................... 2 Years
Approximate Assembly & Setup Time ................................................................. 45 Minutes
Serial Number Location .......................................................................... Machine ID Label
ISO 9001 Factory .................................................................................................. Yes
Certified by a Nationally Recognized Testing Laboratory (NRTL) ......................................... Yes
Features
Features Ground Steel Table Inserts
Includes Formed and Welded Steel Stand
100‐Grit Sleeve Included for Each Spindle
Cast‐Iron Table
Table Tilts 45 deg.
-
1
-
2
Shop fox 1 HP Oscillating Spindle Sander W1686 Owner's manual
- Category
- Power sanders
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Woodstock 1 HP Oscillating Spindle Sander W1686 Owner's manual
-
-
Shop fox W1668 User manual
-
-
-
-
-
-
Grizzly W1712 Owner's manual
-
Other documents
-
-
Grizzly Industrial G1071 Owner's manual
-
-
-
Grizzly Industrial G0529 Owner's manual
-
-
-
-
-
JET 723950 Owner's manual
