Candy COW4854TWM6/1-S User manual

Brand: Candy

Model: COW4854TWM6/1-S

Category: Washing machines

Type: User manual

This manual is also suitable for

Thank you for choosing this product.

We are proud to offer the ideal product for

you and the best complete range of home

appliances for your daily routine.

Carefully read this manual for correct and

safe appliance use and for helpful tips on

efficient maintenance.

Only use the washing

machine after

carefully reading these instructions. We

recommend you always keep this manual on

hand and in good condition for any future

owners.

Each product is identified by a unique 16-

character code, also called the “serial

number”, printed on the sticker. This can be

found inside the door opening. This code is

a unique code for your product that you will

need to

you need to contact the Customer Service

Centre.

This appliance is marked according to

the European directive 2012/19/EU

on Waste Electrical and Electronic

Equipment (WEEE).

WEEE contains both polluting substances (which

can cause negative consequences for the

environment) and basic components (which can

be re

used). It is important to have WEEE

subjected to specific treatments, in order to

remove and dispose properly all pollutants, and

recover and recycle all materials. Individuals can

play an important role in ensuring that WEEE

does not become an environmental issue; it is

essential to follow some basic rules:



WEEE should not be treated as household

waste;



WEEE should be handed over to the relevant

collection points managed by the municipality or

by registered companies. In many countries, for

large WEEE, home collection could be present.

In many countries, when you buy a new

appliance, the old one may be returned to the

retailer who has to collect it free of charge on a

one

-to-

one basis, as long as the equipment is of

equivalent type and has the same functions as

the supplied equipment.

GENERAL SAFETY RULES

INSTALLATION

DETERGENT DRAWER

PRACTICAL HINTS

CLEANING AND MAINTENANCE

REMOTE CONTROL (WI-FI)

QUICK USER GUIDE

CONTROLS AND PROGRAMS

DRYING CYCLE

10.

TROUBLESHOOTING AND WARRANTY

Contents

Environmental conditions

FOR U.K. ONLY

On receipt of your appliance please

check it carefully for damage. Any

damage found must be reported

to the

delivery driver immediately.

Alternatively

damage found must be

reported to the retailer within 2 days of

receipt.

1. GENERAL SAFETY

RULES

 This appliance is intended to

be used in household and

similar applications such as:

- Staff kitchen areas in shops, offices

and other working environments;

- Farm houses;

- By clients in hotels, motels and

other residential type environments;

- Bed and breakfast type environments.

A different use of this appliance

from household environment

or from typical housekeeping

functions, as commercial use by

expert or trained users, is excluded

even in the above applications. If

the appliance is used in a manner

inconsistent with this it may reduce

the life of the appliance and may

void the manufacturer’s warranty.

Any damage to the appliance or

other damage or loss arising

through use that is not consistent

with domestic or household use

(even if located in a domestic or

household environment) shall not

be accepted by the manufacturer to

the fullest extent permitted by law.

 This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance

in a safe way and understand the

hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made

by children without supervision.

 Children should be supervised

to ensure that they do not play

with the appliance.

 Children of less than 3 years

should be kept away unless

continuously supervised.



If the supply cord is damaged, it

must be replaced by a special

cord or assembly available from

the manufacturer or its service

agent.



Only use the hose-sets

supplied with the appliance for

the water supply connection

(do not reuse old hose-sets).



Water pressure must be between

0.1 MPa and 1 MPa.



Make sure carpets or rugs do

not obstruct the base or any of

the ventilation openings.

 The final part of a washer dryer

cycle occurs without heat (cool

down cycle) to ensure that the

items are left at a temperature

that ensures that the items will

not be damaged.



After installation, the appliance

must be positioned so that the

plug is accessible.

 The appliance must not be

installed behind a lockable

door, a sliding door or a door

with a hinge on the opposite

side to that of the washer

dryer, in such way that a full

opening of the washer dryer

door is restricted.

 The maximum load capacity of

dry clothes depends on the

model used (see control panel).

 The appliance is not to be used

if industrial chemicals have

been used for cleaning.

 Do not dry unwashed items in

the washer dryer.



Items that have been soiled with

substances such as cooking oil,

acetone, alcohol, petrol, kerosene,

spot removers, turpentine, waxes

and wax removers should be

washed in hot water with an extra

amount of detergent before being

dried in the washer dryer.

 Items such as foam rubber

(latex foam), shower caps,

waterproof textiles, rubber

backed articles and clothes or

pillows fitted with foam rubber

pads should not be dried in the

washer dryer.

 Fabric softeners, or similar

products, should be used as

specified by the fabric softener

instructions.

 Oil-affected items can ignite

spontaneously, especially when

exposed to heat sources such

as a washer dryer. The items

become warm, causing an

oxidation reaction in the oil,

Oxidation creates heat. If the

heat cannot escape, items can

become hot enough to catch

fire. Piling, stacking or storing

oil-effected items can prevent

heat from escaping and so

create a fire hazard.

 If it is unavoidable that fabrics

contain vegetable or cooking

oil or have been contaminated

by hair care products be

placed in a washer dryer they

should first be washed in hot

water with extra detergent -

this will reduce, but not

eliminate, the hazard.



Remove all objects from pockets

such as lighters and matches.

WARNING:

never stop a washer dryer before

the end of the drying cycle

unless all items are quickly

removed and spread out so that

the heat is dissipated.



To consult the product technical

specification please refer to the

manufacturer website.

 The technical details (supply

voltage and power input) are

indicated on the product rating

plate

 Make sure that the electrical

system is earthed, complies

with all applicable law and that

the (electricity) socket is

compatible with the plug of the

appliance. Otherwise, seek

qualified professional assistance.

 The use of converters, multiple

sockets or extension cords is

strongly advised against

 Before cleaning or maintaining

the washing machine, unplug

the appliance and turn off the

water tap.

 Do not pull on the power cord

or appliance to unplug the

machine.

 Make sure there is no water in

the drum before opening the

door.

 Do not expose the washing

machine to rain, direct sunlight

or other weather elements.

Protect from possible freezing.

 When moving, do not lift the

washing machine by the knobs

or detergent drawer; during

transport, never rest the door on

the trolley. We recommend two

people lift the washing machine.

 In the event of fault and/or

malfunction, turn off the

washing machine, close the

water tap and do not tamper

with the appliance.

Immediately contact the

Customer Service Centre and

only use original spare parts.

Failure to observe these

instruction may jeopardise

appliance safety.

WARNING:

water may reach very high

temperatures during the

wash cycle.

WARNING:

the appliance must not be

supplied through an external

switching device, such as a

timer, or connected to a circuit

that is regularly switched on

and off by a utility.

Electrical connections and

safety instructions

2. INSTALLATION



Remove the

transportation

screws

(A)

on the back and

remove the

flat washers,

rubber bungs and plastic spacer

tubes

(B)

as illustrated

in figure 1



If the washing machine is

built

, unscrew the

transportation screws

(A)

and

remove the

flat washers,

rubber bungs and plastic spacer

tubes

(B)



During the removal of the screws

occasionally spacer tubes fall

inside the product, these can be

remove by tilting the product forward

and recovering them from the floor

or inside the base of the machine.



Cover the open transportation screw

holes with the

plastic caps

included in the instruction bag.



Place the corrugated plastic

sheet, found on top of the

appliance during the unpacking

process*

, into the base of the

appliance as shown in

figure 2

(according to the model,

consider version A, B or C).

In some models, the corrugated

plastic sheet is not provided.

WARNING:

keep packaging materials

away from children.



Connect the water hose to the water

supply tap (fig. 3)

only using the hose

supplied with the appliance (do not

reuse old hose-sets).



SOME MODELS

may include one or

more of the following features:



HOT&COLD (fig. 4):

water mains connection settings with hot

and cold water for higher energy savings.

Connect the grey tube to the cold water

tap

and the red one to the hot water

tap. The machine ca

n be connected to

the cold water tap only: in this case, some

programs may start a few minutes later.



AQUASTOP (fig. 5):

a device located on the supply tube that

stops water flow if the tube deteriorates;

in this case, a red mark will appear in the

window “A

” and the tube must be

replaced. To unscrew the nut, press the

one-way lock device "B".



AQUAPROTECT –

SUPPLY TUBE WITH

GUARD (fig. 6):

Should water leak from the primary

internal tube "A"

, the transparent

containment sheath "B

" will contain water

to permit the washing cycle to complete.

At the end of the cycle, contact the

Customer Service Centre to replace the

supply tube.

Hydraulic connections



The washing machine should be installed in

its final position such that the water fill hose

is not kinked or trapped. The corrugated

drain hose should be inserted into suitable

drain pipe of between 50 cm and 85 cm

heig

ht above the floor using the curved drain

hose support. If an under sink connection is

used the drain hose must be routed above

the sink overfill opening to prevent back

siphoning. Care must be taken to avoid

kinking or trapping the drain hose

(fig. 7)



Level the appliance using the feet as

illustrated in figure 8:

turn the nut clockwise to release the

screw;

rotate the foot to raise or lower it until it

touches to the floor;

lock the foot, screwing in the nut, until it

tightens against to the bottom of the

washing machine.



Plug in the appliance.

ACCESSORY SOLD SEPARATELY

WARNING:

contact the Customer Service Centre

should the power cord need

replacement.

Installation faults are not covered

the manufacturers warranty.

Setting

3. DETERGENT DRAWER

The detergent draw is split into 3

compartments as illustrated in figure 9:

 compartment "1": for prewash detergent;

 compartment “ ”: for special additives,

softeners, starch fragrances, etc.;

 compartment "2": for washing

detergent.

A liquid detergent cup is also included IN

SOME MODELS (fig. 10). To use it, place it

in compartment "2". This way, liquid

detergent will only enter the drum at the

right time. The cup can also be used for

bleach when the “Rinse” program is

selected.

SOME MODELS are provided with the

automatic dosage, this carries out a

precise measurement of detergent and

softener.

In this case, refer to the

specific section in the CONTROLS

AND PROGRAMS chapter for details.

WARNING:

some detergents are not designed for

use in the dispenser drawer but are

supplied with their o

wn dispenser that

is placed in the drum directly.

WARNING:

only use liquid products; the washing

machine is set to automatically dose

additives at each cycle during the last

rinse.

4. PRACTICAL HINTS

When sorting laundry, make sure:

- have eliminated metallic objects such as

hair clips, pins, coins, from laundry;

- to have buttoned pillow cases, closed zips,

tied loose belts and long robe ribbons;

- to have removed rollers, hooks or clips

from curtains;

- to have carefully read clothing washing

labels;

- to have removed any persistent stains

using specific detergents.



When washing rugs, bedcovers or other

heavy clothing, we recommend you avoid

the spinning cycle.



To wash wool, make sure the item can be

machine washed. Check the fabric label.



Leave the appliance’s door slightly open

between washes, to prevent possible bad

smells developing inside the machine.

Tips on how to save money and not

damage the environment when using your

appliance.

 Load the machine to the highest capacity

shown in the programme table for each

programme - this will allow you to SAVE

energy and water.

 Noise and residual laundry moisture are

affected by spin speed: a faster spin is

associated with greater noise and lower

residual moisture in the laundry.

 The most efficient programmes in terms

of combined use of water and energy are

usually the longer-lasting ones with lower

temperature.

Maximise the load size

 Achieve the best use of energy, water,

detergent and time by using the

recommended maximum load size.

Save up to 50% energy by washing a full

load instead of 2 half loads.

Do you need to pre-wash?

 For heavily soiled laundry only!

SAVE detergent, time, water and

between 5 to 15% energy consumption

by NOT selecting Prewash for slight to

normally soiled laundry.

Is a hot wash required?

 Pretreat stains with stain remover or soak

dried in stains in water before washing to

reduce the necessity of a hot wash

programme. Save energy by using a low

temperature wash programme.

Before using a drying programme

(WASHER-DRYERS)

 SAVE energy and time by selecting a

high spin speed to reduce the water

content in laundry before using a drying

programme.

Below is a short guide with tips and advice

on the use of detergent.

 Only use detergents suitable for machine

washing.

 Select your detergent according to the

type of fabric (cotton, delicates,

synthetics, wool, silk, etc.), the colour, the

type and level of soiling and the

programmed washing temperature.

 To use the right amount of detergent,

softener or any other additives, carefully

follow the manufacturer’s instructions

every time: correctly using the

appliance with the right dose allows

you to avoid waste and to reduce the

environmental impact.

Dosing the detergent

Useful advice for saving

Load tips

 Too much detergent leads to excessive

foam, which prevents the cycle being

carried out correctly. It could also affect

the quality of the washing and rinsing.

The use of ecological detergents without

phosphates may cause the following

effects:

- cloudier rinse drain water: This effect is

tied to the suspended zeolites which do

not have negative effects on rinse

efficiency.

- white powder (zeolites) on laundry at

the end of the wash: this is normal, the

powder is not absorbed by fabric and does

not change its colour.

To remove the zeolites, select a rinse

programme. In the future consider using

slightly less detergent.

- foam in the water at last rinse: this does

not necessary indicate poor rinsing.

Consider using less detergent in future

washes.

- abundant foam: This is often due to the

anionic surfactants found in the detergents

which are hard to eliminate from laundry.

In this case, do not re-rinse to eliminate

these effects: it will not help at all.

We suggest conducting a maintenance

wash using a proprietary cleaner.

If the problem persists or if you suspect a

malfunction, immediately contact an

Authorised Customer Service Centre.

For washing wool or silk, only use

detergents specifically formulated for

these fabrics.

For washing at temperatures below

40°C we recommen

d the use of liquid

detergents or detergents specifically

labeled as suitable for low temperature

washing.

For washes between 40°C and 60°C

the type of detergent used needs to be

appropriate for the type of fabric and

level of soiling. Normal powders are

suitable for “white” or colour fast fabrics

with high soiling, while liquid detergents

or “colour protecting” powders are

suitable for coloured fabrics with light

levels of soiling.

When washing heavily soiled whites,

we recommend using cotton programs

60°C

or above and a normal washing

powder (heavy duty) that contains

bleaching agents that at medium/high

temperatures provide excellent results.

5. CLEANING AND

MAINTENANCE

Looking after your appliance correctly can

extend its lifespan.

 Disconnect the machine from the power

supply.

 Clean the appliance’s external cabinet,

using a damp cloth and AVOIDING

ABRASIVES, ALCOHOL AND/OR

DILUENTS.

 It is advisable to regularly clean the

detergent drawer to avoid the

accumulation of detergent and additive

residues.

 Remove the drawer gently but firmly.

 Clean the drawer under running water

and put it back into its compartment.

FOR MODELS WITH AUTOMATIC LIQUID

DETERGENT AND SOFTENER DOSING

SYSTEM:

 Pull out the drawer completely by

pressing the release button, paying

attention to the leakage of detergent

residues.



Fill the drawer with hot water.

 Shake the drawer in order to let the water

flow in all the compartments.

 Empty the drawer from excess water and

reinsert it completely.

WARNING:

DO NOT use acid products (for example

vinegar) or aggressive detergents to

clean the drawer, in order to avoid

damaging the seals and/or internal

parts of the appliance.

Before proceeding with cleaning, all

the compartments must be empty.

Drawer cleaning

Cleaning the appliance’s exterior

 The appliance has a special filter that

traps larger residues that could block the

draining system, such as buttons or coins

(depending on the model, consider

version A or B).

We recommend checking and cleaning

the filter 5 or 6 times a year.

 Disconnect the machine from the power

supply.

 Ensure all the water has been emptied

from the drum.

 Before unscrewing the filter, we

recommend you place an absorbent cloth

under it to keep the floor dry. A small

amount of water will come out of the filter

as you remove it - this is normal.

 Turn the filter counter-clockwise to the

limit stop.

 Remove and clean the filter; when

finished, replace it turning it clockwise.

The filter handle will be locked when it is

not possible to turn any further and the

handle is horizontal. Smearing a small

amount of liquid soap on the filter seal will

help refitting.

 Repeat the previous steps in reverse

order to reassemble all parts.

 If the appliance is kept in a non-heated

room for long periods of time, all water

residues must be completely removed

from the pipes.

 Disconnect the machine from the power

supply socket.



Detach the tube from the drainage system

and clip on the rear of the machine and

lower it, fully draining water into a bowl.

 Secure the drain tube with the drainage

system and clip on the rear of the

machine when finished.

 Keep the door glass and gasket clean.

FOR MODELS WITH AUTOMATIC

LIQUID DETERGENT AND SOFTENER

DOSING SYSTEM:

should you need to tilt or move the

machine, remove the detergent drawer

before proceeding, keeping it

horizontal so as to avoid any leakage.

Suggestions for moves or

prolonged disuse

Cleaning the pump filter

6. REMOTE CONTROL (WI-FI)

This appliance is equipped with Wi-Fi

technology that allows you to control it

remotely via App.

APPLIANCE PAIRING (ON APP)



Download the hOn

App on your device by

framing the following QR code:

or by the link:

go.haier-europe.com/download-app



Open the App, create the user profile (or

log-

in if it is already created previously)

and pairing the appliance following the

instructions on the device display.

TO ENABLE REMOTE CONTROL



Check that the router is switched on and

connected to the Internet.



Load the laundry, close the door, add the

detergent if it’s necessary.



Turn the programme selector

to the

REMOTE CONTROL

(Wi-Fi) position

the door will lock and the controls on the

control panel will be disabled.

 Start the cycle using the app. When the

cycle has been completed, turn off the

machine by turning the programme

selector to the OFF

position to unlock the

door.

TO DISABLE REMOTE CONTROL



To exit REMOTE CONTROL

mode while

a cycle is underway, turn the programme

selector to any position other than

REMOTE CONTROL (Wi-Fi),

without

going through the OFF

. The control

panel on the applianc

e will be operative

once again, and if the cycle is paused,

you will be able to open the door once the

DOOR LOCKED

indicator light switches

off.



With the door closed, turn the

knob to the

REMOTE CONTROL (Wi-Fi)

position to

control the appliance using the app once

again. If there is a cycle underway, it will

continue.

For safety reasons, in some wash

cycle phases, the door can be

opened only if the level of the water

is bel

ow its lower edge and if the

temperature is less than 45°C. If

these conditions are met, wait for the

DOOR LOCKED light to switch off

before opening the door.

The frequency of the home Wi-Fi network

has to be set on the 2.4 GHz band. You

can not configure the machine if your

home network is set to the 5 GHz band.

Get all the details of the Wi-Fi

functions by browsing the App in

DEMO mode.

The App is available for devices

running both Android and iOS, both

for tablets and for smartphones.

7. QUICK USER GUIDE

This appliance automatically adjusts the

level of the water to the type and quantity of

washing. This system gives a reduction in

energy consumption and a saving in

washing times.

 Turn on the appliance and select the

required program.

 Adjust the washing settings if necessary

and select the required options.

 Press the programme start button.

 The end of the programme will be

indicated by a message on the display

(on some models, all the indicator lights

on the stage will light up).

 Turn off the appliance.

For any type of wash, see the program

table and follow the operating sequence

as indicated.

Water pressure:

min 0.1 Mpa / max 1 Mpa

Spin r.p.m.: See rating plate.

Power input / Power current fuse amp /

Supply voltage: See rating plate.

8. CONTROLS AND

PROGRAMS

* Depending on model

PLAY/PAUSE button

TEMPERATURE SELECTION

button

SPIN SPEED button

STAIN LEVEL/RAPID/STEAM

LEVEL button**

DELAY START button

OPTIONS button

DRYING SELECTION button

SPECIAL PROGRAMMES button

(only available on certain models)

B+C

CHILD LOCK

**STEAM LEVEL

(only available on certain models)

Technical data

DRYING (WASHER-DRYERS only)

If you would like the drying cycle to

begin automatically after washing,

select the washing programme

required and select the drying cycle.

Or you can finish the wash and then

select the drying programme.

Program selection

 When the programme selector is turned

the display lights up to show the settings

for the programme selected.

 Switch off the washing machine by

turning the selector to OFF.

- Language setting

 After connecting the machine to the

network and turning it on, press the

"TEMPERATURE SELECTION" or

"SPIN SPEED" button to display the

available languages.

 Select the desired language pressing the

PLAY/PAUSE button.

- Change the language

 If you want to change the setting language,

you will have to press simultaneously

"TEMPERATURE SELECTION" and

"DELAY START" buttons for about 5

seconds. ENGLISH will appear on the

display, and you will be able to choose a

new language (by pressing

"TEMPERATURE SELECTION" or "SPIN

SPEED" button).

 Press PLAY/PAUSE button to confirm

your choice.

 To start the selected cycle with the preset

parameters, press PLAY/PAUSE. When

the programme is running, the display will

show the time to elapse.

 Moreover, If you want to modify the

chosen programme, press the desired

options buttons, modify the default

parameters and then press

PLAY/PAUSE button to start the cycle.

 After switching on the appliance, wait a

few seconds for the programme to start

running.

PROGRAMME DURATION

 When a programme is selected the

display automatically shows the cycle

duration, which can vary, depending on

the options selected.

 Once the programme has started you will

be kept informed constantly of the time

remaining to the end of the wash.

 The appliance calculates the time to the

end of the selected programme based

upon a standard loading, during the cycle,

the appliance corrects the time to that

applicable to the size and composition of

the load.

PROGRAMME END

 When the display shows that the

programme is finished and the DOOR

LOCKED indicator light has gone out, the

door can be opened.

 At the end of the cycle, switch off the

appliance by turning the selector to OFF.

The programme selector must be

returned to the OFF position at the end

of each cycle or when starting a

subsequent wash cycle prior to the next

programme being selected and started.

Only the options compatible with the

set programme can be selected.

Close the door BEFORE selecting the

button PLAY/PAUSE.

PLAY/PAUSE button

First starting

PROGRAMME selector with OFF

position

WARNING:

don’t touch the buttons while inserting

the plug because the machines

calibrates the systems during the first

seconds: touching the buttons, the

machine couldn’t work property. In

this case, remove the plug and repeat

the operation.

PAUSING THE MACHINE

 While a cycle is running, the machine can

be paused by simply pressing the

PLAY/PAUSE button.

 Press the PLAY/PAUSE button again to

resume the programme from the cycle

phase where it left off.

CANCELLING THE SET PROGRAMME

 To cancel the programme, set the

selector to the OFF position.

 Wait until the DOOR LOCKED light has

gone out before opening the door.

 This button allows you to change the

temperature of the wash cycles.

 It is not possible to raise the temperature

over the maximum allowed for the

programme, in order to protect the

fabrics.

 If you want carry out a cold wash all the

indicators must be off.

 By pressing this button, it is possible to

reduce the maximum speed, and if you

wish, the spin cycle can be cancelled.

 If the label does not indicate specific

information, it is possible to use the

maximum spin expected in the program.

 To reactivate the spin cycle press the

button until you reach the spin speed you

would like to set.

 It is possible to modify the spin speed

without pausing the machine.

This button allows you to choose between

three different options, depending on the

selected programme:

- STAIN LEVEL

 Once the programme has been selected

the wash time set for that programme will

be automatically shown.

 This option allows you to choose between

3 levels of wash intensity modifying the

length of the programme, depending

on how much the fabrics are soiled (can

only be used on some programmes as

shown in the table of programmes).

STAIN LEVEL / RAPID / STEAM

LEVEL button*

The machine is fitted with a special

electronic device, which prevents the

spin cycle should the load be

unbalanced. This reduces the noise

and vibration in the machine and so

prolongs the life of your machine.

An over dosing of detergent can

cause excessive foaming. If the

appliance detects the presence of

excessive foam, it may exclude the

spinning phase or extend the duration

of the program and increase water

consumption.

To prevent damage to the fabrics, it is

not possible to increase the speed

over the maximum allowed for the

programme.

SPIN SPEED button

TEMPERATURE SELECTION

button

For safety reasons, in some wash

cycle phases, the door can be opened

only if the level of the water is below

its lower edge and if the temperatur

is less than 45°C. If these conditions

are met, wait for the DOOR LOCKED

light to switch off before opening the

door.

- RAPID

The button becomes active when

you select the RAPID (14'/30'/44')

programme on the knob and allows you to

select one of three durations indicated.

- STEAM LEVEL*

After selecting the EASY IRON PLUS

programme, you can use this button to

choose between three steam treatments of

different intensities, designed for dry or wet

garments and depending on the type of

fabric:

- COTTON (default selection)

This programme is used for cotton

garments. On wet fabrics (e.g., after

washing), it is suitable for relaxing

creases after spinning; on dry fabrics it

is instead designed to achieve the ideal

humidity level for easier ironing.

- SYNTHETIC (press button once)

This programme is used for synthetic

garments. On wet fabrics (e.g., after

washing), it is suitable for relaxing

creases after spinning; on dry fabrics it

is instead designed to achieve the ideal

humidity level for easier ironing.

- DELICATES (press button twice)

With the help of steam, the cycle

refreshes and relaxes creases in

garments after use. The programme

consists of an initial phase in which the

steam acts and a final phase in which the

excess humidity is removed for immediate

use. The cycle is suitable for dry fabrics.

*STEAM LEVEL

(only available on certain models)

 This button allows you to pre-programme

the wash cycle to delay the start of the

cycle for up to 24 hours.

 To delay the start use the following

procedure:

- Select the required programme.

- Press the button once to activate the

delay start and then press it again (or

hold it) to set the desired delay. The

delay increases each time the button is

pressed up to 24 hours, at which point

pressing the button again will reset the

delay start to zero.

- Confirm by pressing the PLAY/PAUSE

button. The delay countdown will begin

and when it has finished the programme

will start automatically.

 It is possible to cancel the delay start by

turning the programme selector to OFF.

If there is a break in the power supply

whilst the machine is operating, when

the power is restored, the machine will

restart from the beginning of the phase it

was in when the power was lost.

This button allows you to choose between

three different options:

- PREWASH

 This option allows you to make a prewash

and it is particularly useful for heavily

soiled loads (can be used only on some

programmes as shown in the table of

programmes).

 We recommend you use only 20% of the

recommended quantities shown on the

detergent pack.

- EXTRA RINSE

 This option allows you to add one rinse at

the end of the washing cycle and is useful

for people with delicate and sensitive

skin, for which a small amount of

detergent residue can cause irritations or

allergies.

OPTIONS button

DELAY START button

These options must be selected before

pressing the PLAY/PAUSE button.

 It is advisable to also use this function for

the children clothes and for the washing

of heavily soiled items, which requires a

lot of detergent to be used, or for the

washing of toweling items whose fibres

mostly have the tendency to hold the

detergent.

- HYGIENE +

Activated when you set 60°C of

temperature. This option allows deep

cleaning of your clothes by maintaining the

same temperature for the whole wash.

 Automatic washing/drying cycle:

after the selection of washing programme

according to laundry type, select a degree

of dryness by pressing this button. At the

end of the washing programme, the

selected drying cycle will start automatically.

If a washing programme is not compatible

with automatic drying is selected, this

function will not be activated.

 To only perform a drying cycle:

select the desired drying programme in

conjunction with your fabrics, by pressing

this button it is possible to select a degree

of dryness that is different to the default

one

(except for the wool drying programme)

 To cancel the cycle during the drying

phase, press the button for about 3

seconds.

 "End" will appear in the display at the

end of the programme and the DOOR

LOCKED light will go off, it is now

possible to open the door.

(Only available on certain models)

This button allows you to choose between

three different options (available for some

programmes only):

- SINGLE ITEM

 This option (which can be set in several

programs) optimizes the water and

energy consumption of the selected

program, maintaining the washing

performance unchanged.

 SINGLE ITEM is designed for reduced

loads and lightly soiled garments, aiming

to limit the unnecessary waste.

- NIGHT WASH

 This option reduces the intermediate spin

speed to 400 rpm, where applicable,

increase the water level during rinsing

and keep the laundry immersed in water

after the final rinse, in order to spread the

fiber perfectly.

 During the drum water retention phase,

the machine is in pause mode.

 Press PLAY to end the cycle with the

spin (which can be reduced or removed

with the specific button) and drain phase.

 Thanks to electronic control, the water in

the intermediate phases is emptied

silently, making this option very useful for

washing at night.

- DRUM CLEAN

 Developed to clean the washing machine

drum.

 Use only powder detergent.

 Do not start the programme with laundry

in the washing machine.

SPECIAL PROGRAMMES button

If you exceed the maximum dryable load

of laundry indicated in the programme

table, the laundry may not be dried

satisfactory.

DRYING SELECTION button

These options must be selected

before pres

sing the PLAY/PAUSE

button.

If an option is selected that is not

compatible with the selected

programme then the option indicator

light first flashes and then goes off.

 It is suggested that this is carried out after

every 50 washing cycles.

 The option can only be selected for the

DRAIN & SPIN programme.

 Pressing simultaneously the buttons

"TEMPERATURE SELECTION" and "SPIN

SPEED" for about 3 seconds, the machine

allows you to lock the keys. In this way, you

can avoid making accidental or unwanted

changes if a button on the display is pressed

accidently during a cycle.

 The key lock can be simply cancelled by

pressing the two buttons simultaneously

again or turning off the appliance.

The display’s indicator system allows you to

be constantly informed about the status of

the machine.

*Only available on certain models

1) DOOR LOCKED INDICATOR LIGHT

 The indicator light is illuminated when the

door is fully closed.

 When PLAY/PAUSE is pressed on the

machine with the door closed, the

indicator will flash momentarily and then

illuminate.

 A special safety device prevents the door

from being opened immediately after the

end of the cycle. Wait for 2 minutes after

the wash cycle has finished and the

DOOR LOCKED light has gone out before

opening the door. At the end of the cycle

turn the programme selector to

OFF

2) STAIN LEVEL INDICATOR LIGHT

The indicator light shows the selection of

the relevant option.

3) Kg Detector INDICATOR LIGHT

(active only on certain programmes)

 During the first minutes of the cycle, the

"Kg Detector" indicator will remain on

while the intelligent sensor will weigh the

laundry and adjust the cycle time, water

and electricity consumption accordingly.



Through every wash phase

"Kg Detector"

allows to monitor information on the wash

load in the drum and in the first minutes of

the wash it:

- adjusts the amount of water required;

- determines the length of the wash cycle;

- controls rinsing according to the type of

fabric selected to be washed it;

- adjusts the rhythm of drum rotation for

the type of fabric being washed;

If the door is not properly closed,

the light will continue to flash

for

about 7 seconds

, after which the

start command will be automat

ically

cancelled. In this case, close

the

door in the proper way and

press

the PLAY/PAUSE button.

Close the door BEFORE selecting the

PLAY/PAUSE button.

Digital Display

CHILD LOCK

These options must be selected

before pressing the PLAY/PAUSE

button.

If an option is selected that is not

compatible with the selected

programme then the option indicator

light first flashes and then goes off.

Page is loading ...

Candy COW4854TWM6/1-S User manual

Brand: Candy

Model: COW4854TWM6/1-S

Category: Washing machines

Type: User manual

This manual is also suitable for

Download PDF

report

Candy COW4854TWM6/1-S User manual

This manual is also suitable for

Candy COW4854TWM6/1-S User manual

Related papers

Other documents