Yerasov SCS PB-4 Owner's manual

Brand
Yerasov
Model
SCS PB-4
Category
Guitar accessories
Type
Owner's manual

Yerasov SCS PB-4 is a pedalboard designed to be used with the SCS series of pedals. It allows for easy connection and organization of pedals, providing a clean and professional setup. The pedalboard features a durable construction and a compact design, making it suitable for both stage and studio use. With its versatile design, the Yerasov SCS PB-4 can accommodate a variety of pedal configurations, allowing musicians to customize their setups to meet their specific needs.

Yerasov SCS PB-4 is a pedalboard designed to be used with the SCS series of pedals. It allows for easy connection and organization of pedals, providing a clean and professional setup. The pedalboard features a durable construction and a compact design, making it suitable for both stage and studio use. With its versatile design, the Yerasov SCS PB-4 can accommodate a variety of pedal configurations, allowing musicians to customize their setups to meet their specific needs.

PEDAL BOARD
PB-4
PB-6
PB-8
Owner manual
2
SAFETY PRECAUTIONS
Please protect this equipment from falling, impacts and excess humidity.
BEFORE YOU START
2. Unscrew the flat side-knurled thumbscrews
holding the Pedal Board's bottom cover.
3. The cover has an additional inner mount, so
slide it a little bit towards the screws and
remove it from the Pedal Board.
1 .SCS (Secret Connecting System)
pedalboard is designed to use with SCS series
pedals. Before using an SCS Pedal Board, it
must be prepared for the first run accordingly.
Regardless of the model (PB-4/6/8), all of the
SCS pedalboards are assembled to use and
connected the same way.
Attention! Please read this manual carefully before you start!
3
6. Attach the SCS pedals to the Pedal Board
with the captive screws.
5. Place the pedals on the Pedal Board. The
pedals' sequence is no important, except of
FS-12 (refer to p.8).
4. Pedal Board is now open.
9. Attention! All of the switches located on the
Pedal Board' s inner circuit board are
depressed by default. If you are going to take a
pedal off the Pedal Board for some reason
(except the first and the last in line), please
press down the appropriate S1 (or S2) bypass
switch located on the Pedal Board's inner
circuit board to avoid a signal path's gap in the
effects sequence. Those switches are located
close to the Pedal Board's pedal connectors.
4
8. The SCS series has the FS-12 pedal, which
can be used either as a stand-alone device or
as a common bypass device for the whole
Pedal Board. In this case it should be placed
leftmost on the Pedal Board, while the
rightmost place must not be empty. The S3
switch located on the Pedal Board's inner
circuit board should be depressed when using
the FS-12. In any other case of using SCS
pedal in the leftmost position this switch should
be pressed down.
7. Connect the pedals to the Pedal Board with
the dedicated cables, which are supplied
accessories (spare cables included as well).
5
10. This is how an assembled, ready-to-use
Pedal Board looks from inside.
11. Putting back the bottom cover, assemble
the Pedal Board.
12. Tighten the cover's side-knurled screws.
6
Size, mm PB-4..........................................................................
PB-6..........................................................................
PB-8.............................................. ............................5
Weight, kg net B-4.........................................................................................
PB-6.........................................................................................
PB-8.........................................................................................
P 0,7
1,0
1,3
260õ113õ33
392õ113õ33
24õ113õ33
TECHNICAL SPECIFICATIONS
SCS Pedal Board............................................................................................................1 pcs
Connection cable for PB-4..................................................................................... 5 pcs
PB-6......................................................................................7 pcs
PB-8......................................................................................9 pcs
Owner manual..................................................................................................................1 pcs
Cardboard box.................................................................................................................1 pcs
Pedal Board cover...........................................................................................................1 pcs
PACKAGE CONTENTS
13. The Pedal Board is now ready to use. Guitar
is connected to the rightmost pedal's input,
while leftmost pedal's output is connected to
the amplifier. Power supply for all the SCS
pedals attached is cross-connected from inside
of the Pedal Board. One external power supply
unit connected to any pedal is enough to use.
7
FOR NOTES
YERASOV MUSIC CORPORATION
www.yerasov.ru e-mail: sale@yerasov.ru
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Yerasov SCS PB-4 Owner's manual

Brand
Yerasov
Model
SCS PB-4
Category
Guitar accessories
Type
Owner's manual

Yerasov SCS PB-4 is a pedalboard designed to be used with the SCS series of pedals. It allows for easy connection and organization of pedals, providing a clean and professional setup. The pedalboard features a durable construction and a compact design, making it suitable for both stage and studio use. With its versatile design, the Yerasov SCS PB-4 can accommodate a variety of pedal configurations, allowing musicians to customize their setups to meet their specific needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents