Carlisle JGA & JGHV Spray Gun Series User manual

JGA & JGHV Spray Gun Series
Carlisle
Brand
Carlisle
Model
JGA & JGHV Spray Gun Series
Category
Paint Sprayer
Type
User manual

This manual is also suitable for

SB-2-252-R4 (3/2019) 1 / 8 www.carlisleft.com
■ Major Repair Kit KK-4987-2
IMPORTANT: Before using this equipment,
read all safety precautions and instructions.
Keep for future use.
Strain material thru 60 or 90 mesh screen.
Adjust fluid pressure to deliver the desired
paint volume. Adjust air pressure and
flow to provide a uniform dispersion of
atomized paint throughout the pattern.
Keep air pressure as low as possible to
minimize bounce - back and overspray.
Excessive fluid flow will result in heavy
center spray patterns. Inadequate flows
may cause the pattern to split. See
“Troubleshooting”, Page 6, if any problems
occur.
PREVENTIVE MAINTENANCE
To clean air cap and fluid tip, brush exterior
with a stiff bristle brush. If necessary
to clean cap holes, use a broom straw
or toothpick. Never use a wire or hard
instrument. This may scratch or burr holes
causing a distorted spray pattern.
To clean fluid passages, remove excess
material at source, then flush with a
suitable solvent using a device such as the
SolventSaver™ (see Accessories). Wipe
gun exterior with a solvent dampened
cloth. Never completely immerse in
solvent as this is detrimental to the
lubricants and packings.
Note
When replacing the fluid tip or fluid
needle, replace both at the same
time. Using worn parts can cause
fluid leakage. Also, replace the
needle packing at this time. Lightly
lubricate the threads of the fluid
tip before reassembling. Torque
to 20-25 ft. lbs. Do not overtighten
the fluid tip.
To prevent damage to the fluid tip
(4) or fluid needle (33), be sure to
either 1) pull the trigger and hold
while tightening or loosening the
fluid tip or 2) remove fluid needle
adjusting screw (28) to relieve
spring pressure against needle
collar.
DESCRIPTION
The JGA-510 can be utilized with the wide
range of air caps and needles. It is a general
purpose, heavy duty, high production
spray gun suitable for use with most
types of materials. The fluid tip and needle
and internal fluid passages are stainless
steel.
Conversion to HVLP - The JGA-510, plus
JGA-503 models, can be converted to
HVLP if desired. Contact DeVilbiss for
information.
Note
This gun includes 300 series stainless
steel fluid passages and 300/400
series tip and needle. Guns may
be used with chlorinated solvent
materials, but see page 2 for
additional warnings.
Important: This gun may be used with
most common coating and finishing
materials. It is designed for use with mildly
corrosive and non-abrasive materials. If
used with other high corrosive or abrasive
materials, it must be expected that
frequent and thorough cleaning will be
required and the necessity for replacement
of parts will be increased.
OPERATION
Note
Protective coating and rust inhibitors
have been used to keep the gun in
good condition prior to shipment.
Before using the gun, flush it with
solvent so that these materials will be
removed from fluid passages.
A
C
DBE
■
Government NSN No. 4940-01-046-9919 =
KK-4987-2.
IMPORTANT! DO NOT DESTROY
It is the Customer's responsibility to have all operators and service personnel read and understand this manual.
Contact your local DeVilbiss representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS DEVILBISS PRODUCT.
FLUID INLET GASKET (7) REPLACEMENT
INSTRUCTIONS
1. Remove fluid inlet adapter with ap-
propriate wrench.
2. Clean Loctite from gun body inlet
threads and seal area.
3. Place gasket (7) squarely onto the fluid
inlet adapter and push it down until it
is flat against the boss.
4. Place a couple of drops of medium
strength blue No. 242 Loctite on
threads before installing fluid inlet
adapter.
5. Torque fluid inlet adapter to 20-25 ft.
lbs., and tighten locknut.
SPRAY GUN LUBRICATION
Daily, apply a drop of SSL-10 spray gun
lube at trigger bearing stud (21) and the
stem of the air valve (13) where it enters
the air valve assembly (17). The shank of
the fluid needle (33) where it enters the
packing nut (19) should also be oiled. The
fluid needle packing (18) should be lubri-
cated periodically. Make sure the baffle
(6) and retaining ring (1 or 2 ) threads are
clean and free of foreign matter. Before
assembling retaining ring to baffle, clean
the threads thoroughly, then add two
drops of SSL-10 spray gun lube to
threads. The fluid needle spring (30) and
air valve spring (12) should be coated
with a very light grease, making sure that
any excess grease will not clog the air
passages. For best results, lubricate the
points indicated, daily.
A. Trigger Points
B. Packing
C. Adjusting Valves
D. Baffle Threads
E. Air Valve Cartridge
EN
SERVICE MANUAL
JGA-510
CONVENTIONAL SPRAY GUN
EN
SB-2-252-R4 (3/2019)2 / 8www.carlisleft.com
HAZARD CAUSE SAFEGUARDS
Fire
Solvent and coatings can be highly flammable Adequate exhaust must be provided to keep air free of
or combustible especially when sprayed. accumulations of flammable vapors.
Smoking must never be allowed in the spray area.
Fire extinguishing equipment must be present
in the spray area.
Solvent
During use and while cleaning and flushing, Wear eye protection.
Spray
solvents can be forcefully expelled from fluid
and air passages. Some solvents can cause
eye injury.
Inhaling Toxic
Certain materials may be harmful if inhaled, Follow the requirements of the Material Safety Data Sheet
Substances
or if there is contact with the skin. supplied by your coating material manufacturer.
Adequate exhaust must be provided to keep
the air free of accumulations of toxic materials.
Use a mask or respirator whenever there is a chance of inhaling
sprayed materials. The mask must be compatible with the
material being sprayed and its concentration. Equipment must
be as prescribed by an industrial hygienist or safety expert, and
be NIOSH approved.
Explosion Hazard -
Halogenated hydrocarbon solvents - for Guns with stainless steel internal passageways may be used
Incompatible
example; methylene chloride and 1, 1, 1 - with these solvents. However, aluminum is widely used in other
Materials
Trichloroethylene are not chemically com- spray application equipment - such as material pumps,
patible with the aluminum that might be used regulators, valves and cups. Check all equipment items before
in many system components. The chemical use and make sure they can also be used safely with these
reaction caused by these solvents reacting with solvents. Read the label or data sheet for the material you intend
aluminum can become violent and lead to to spray. If in doubt as to whether or not a coating or cleaning
an equipment explosion. material is compatible, contact your material supplier.
General Safety
Improper operation or maintenance of Operators should be given adequate training in the safe use &
equipment. maintenance of the equipment (in accordance with the require
ments of NFPA-33, Chapter 15). Users must comply with all local
and national codes of practice and insurance company require
ments governing ventilation, fire precautions, operation,
maintenance and housekeeping. These are OSHA Sections
1910.94 and 1910.107 and NFPA-33.
Cumulative Trauma
Use of hand tools may cause cumulative Pain, tingling, or numbness in the shoulder, forearm, wrist,
Disorders (“CTD’s”)
trauma disorders (“CTD’s”). hands or fingers, especially during the night, may be early
symptoms of a CTD. Do not ignore them. Should you experience
CTD’s, or musculo- CTD's when using hand tools, tend to affect any such symptoms, see a physician immediately. Other early
skeletal disorders, the upper extremities. Factors which may symptoms may include vague discomfort in the hand, loss of
involve damage to increase the risk of developing a CTD include: manual dexterity, and nonspecific pain in the arm. Ignoring early
the hands, wrist, symptoms and continued repetitive use of the arm, wrist and
elbows, shoulders, 1. High frequency of the activity. hand can lead to serious disability. Risk is reduced by avoiding
neck & back. Carpal 2. Excessive force, such as gripping, pinching, or lessening factors 1-7.
tunnel syndrome & or pressing with the hands and fingers.
tendinitis (such as 3. Extreme or awkward finger, wrist, or arm
tennis elbow or positions.
rotator cuff syndrome)
4.
Excessive duration of the activity.
are examples of
5.
Tool vibration.
CTD’s. 6.
Repeated pressure on a body part.
7. Working in cold temperatures.
CTD’s can also be caused by such activities
as sewing, golf, tennis bowling, to name a few.
The following hazards may occur during the normal use of this equipment.
Please read the following chart before using this equipment.
SAFETY PRECAUTIONS
This manual contains information that is improtant for you to know and understand. This information relates to USER SAFETY
and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the following symbols. Please pay
particular attention to these sections.
Note
Information that you should pay
special attention to.
Important safety information - A hazard
that may cause serious injury or loss
of life.
Important information that tells how
to prevent damage to equipment, or
how to avoid a situation that may cause
minor inury.
EN
SB-2-252-R4 (3/2019) 3 / 8 www.carlisleft.com
AC D E EE EX FF FX FW GX
Tip
Orifice
in./ .110 .080 .070 .070 .070 .055 .042 .063 .034
mm 2.8 2.2 1.8 1.8 1.8 1.4 1.1 1.6 .9
24 P P P
30+ P S S S S
58 S P P P
62HD P P
64HD P P
67HD P
80 S S S S
704 P P P
765 P P P
777 P P
797 P P
9000 S S S S
P = Pressure Feed Combination
S = Suction Feed Combinations
NOZZLE COMBINATIONS
Air Cap
Sizes
Order
From
Chart 2
Fluid Tip and Needle Size
Order From Chart 3
CHART 1
No. on Ref. No. (1) Ref. No. (3)
Cap Air Cap Air Cap Less Ring*
Order With Ring
24 AV-40-24
30+ AV-4239-30
58 AV-439-58
62HD MB-4039-62HD
64HD MB-4039-64HD
67HD MB-4039-67HD
80 MB-4039-80
704 AV-1239-704
765 AV-1239-765
777 31767-777
797 AV-1239-797
9000 AV-440-9000
AIR CAPS
CHART 2
➞
*MBC-368 Retaining Ring
(sold separately) is required
to mount Air Cap to Gun.
CHART 3
FLUID TIPS AND NEEDLES
Tip Orifice Size
In. / (mm)
Ref. No. 4
Fluid Tip
Ref. No. 33
Fluid Needle
303 GR. S.S. TIPS AND 303 GR. S.S. NEEDLES
.110 (2.8) AV-2115-AC JGA-402-C
.086 (2.2) AV-2115-D JGA-402-DEX
.070 (1.8) AV-2115-E JGA-402-E
.070 (1.8) AV-2115-EX JGA-402-DEX
.055 (1.4) AV-2115-FF JGA-402-FF
.042 (1.1) AV-2115-FX JGA-402-FX
.063 (1.6) AV-2115-FW JGA-402-FF
.034 (.9) AV-2115-GX - - -
OPTIONAL 300 GR. S.S. W/ U.H.M.W.
POLYETHYLENE NEEDLE SEAT
.086 (2.2) AV-4915-D - - -
.070 (1.8) AV-4915-E - - -
.055 (1.4) AV-4915-FF - - -
.042 (1.1) AV-4915-FX - - -
.028 (.8) AV-4915-G - - -
OPTIONAL CARBOLOY TIPS AND NEEDLES
(USA ONLY)
.086 (2.2) AV-617-D JGA-409-D
.070 (1.8) AV-617-EE JGA-409-DEEE
.055 (1.4) AV-617-FF JGA-409-FF
.110 (2.8) AV-617-AC JGA-402-C*
* Stainless Steel needle. Tungsten Carbide needle
not available in the AC size (2.8).
AV-1 copper gasket, supplied with AV-617 series
tips, is not required to be used with the JGA-510
series spray gun.
OPTIONAL CARBOLOY TIPS AND NEEDLES
(OUTSIDE USA)
.086 (2.2) AV-1415-D JGA-409-D
.070 (1.8) AV-1415-EE JGA-409-DEEE
.055 (1.4) AV-1415-FF JGA-409-FF
EN
SB-2-252-R4 (3/2019)4 / 8www.carlisleft.com
Ref. Replacement Individual
No. Part No. Description Parts Required
1 See Chart 2 Air Cap w/ Retaining Ring 1
2 MBC-368 Retaining Ring 1
3 See Chart 2 Air Cap Less Retaining Ring 1
4 See Chart 3 Fluid Tip 1
*5 GTI-33-K5 Seal Kit (Kit of 5) 1
6 GTI-425 Baffle Assembly 1
7 MSV-3-K10 Fluid Inlet Gasket (Kit of 10) (blue) 1
8 --- Lock Nut 1
9 --- Fluid Inlet Adapter 1
10 --- Fluid Inlet and Nut Kit 1
*11 --- Gasket 2
*12 --- Spring 1
*13 --- Air Valve 1
*14 --- U Cup Seal 1
*15 --- Washer 1
*16 --- Snap Ring 1
17 JGS-449-1 Air Valve Assembly 1
*18 JGV-463-K3 Packing Kit (Kit of 3) 1
19 34411-122-K10 Packing Nut Kit (Kit of 10) 1
*20 --- Screw 1
21 JGS-478 Stud and Screw Kit (Kit includes 1
3 studs and 5 screws)
22 JGS-477-1 Trigger, Stud and Screw Kit 1
(Kit includes 1 each)
23 JGA-132 Plug 1
24 P-MB-51 Nipple 1
25 JGA-497-1 Fan Adjustment Assembly 1
*26 --- Retaining Ring 1
*27 SSG-8069-K25 O-Ring (Viton) (Kit of 25) 1
28 JGS-16 Adjusting Screw 1
*29 --- Spring Pad (Included 1
with # 30 and 32)
*30 MBD-19-K10 Spring Kit (Kit of 10) 1
31 --- Bushing 1
32 JGA-4041 Bushing, Spring Pad and Knob Kit 1
33 See Chart 3 Fluid Needle 1
34 --- Gun Body 1
* A quantity of necessary parts is included in Major Repair Kit KK-4987-2 for complete
gun repair and should be kept on hand for service convenience.
Suffixes - K10 designates kits of multiple parts. (Example) JGS-72-K10 is a kit of 10 gaskets.
PARTS LIST
■ Government NSN No. 4940-01-046-9919 = KK-4987-2.
1. Remove fluid tip (4).
2. Remove baffle (6).
3. Remove seal (5) from baffle.
4. Assemble seal to baffle with angled
side up as shown at right.
NOTE
The seal should be a tight fit
on the baffle. If it is a loose fit
on the baffle, assure that it is
assembled with the angled
side up.
5. Install baffle on gun.
6. Install fluid tip (4) and tighten to 12-15
ft-lbs.
NOTE
The seal is designed to be a tight
fit on the baffle. The seal should
be able to be removed using
your fingers. If you are unable to
remove the seal using your fingers,
insert a small screwdriver be-
tween the outer lip and the back
of the baffle and pry the seal off.
ANGLED SIDE
THICK SIDE
SEAL
BAFFLE
Pry here if
necessary
GTI-33 Baffle Seal Replacement (5)
EN
SB-2-252-R4 (3/2019) 5 / 8 www.carlisleft.com
*Apply QH-130 (Loctite #242 med. strength blue) sealing
compound on threads.
30
31 29 28
7
8
919
18
34
22
Fluid Inlet
Nipple
3/8 NPS (M)
Torque to
20-25 ft. lbs.
32
33 11
25
26 27
6
5
1
2
4
3
Torque to
12-15 ft. lbs.
10
21
*23
11
16
15
14 13 12
17
Air Inlet
Nipple
1/4 NPS (M)
* 24
Torque to
15 ft. lbs.
20
*
Δ
Δ
Detail Ref. No. 18 - Two piece packing covered by
U.S. Patent No. 5,209,501.
+ Tapered edge faces out towards packing nut.
+Inner PTFE Piece Fluid Packing
Nut
Fluid Needle
Outer
U.H.M.W.
Poly. Piece
See GTI-33 Baffle Seal Replacement
Instructions on Page 4.
EN
SB-2-252-R4 (3/2019)6 / 8www.carlisleft.com
TROUBLESHOOTING
CONDITION CAUSE CORRECTION
Heavy top or
Horn holes plugged. Clean. Ream with non-metallic point.
bottom pattern
Obstruction on top or bottom of fluid tip. Clean.
Cap and/or tip seat dirty. Clean.
Heavy right or left side
Left or right side horn holes plugged. Clean. Ream with non-metallic point.
pattern
Dirt on left or right side of fluid tip. Clean.
Remedies for the top-heavy, bottom-heavy, right-heavy and left-heavy patterns:
1) Determine if the obstruction is on the air cap or the fluid tip. Do this by making a test spray
pattern. Then, rotate the cap one-half turn and spray another pattern. If the defect is inverted,
obstruction is on the air cap. Clean the air cap as previously instructed.
2) If the defect is not inverted, it is on the fluid tip. Check for a fine burr on the edge of the fluid
tip. Remove with #600 wet or dry sand paper.
3) Check for dried paint just inside the opening. Remove paint by washing with solvent.
Heavy center pattern
Fluid pressure too high for atomization Balance air and fluid pressure.
air (pressure feed). Increase spray pattern width with spreader
adjustment valve.
Material flow exceeds air cap's capacity. Thin or lower fluid flow.
Spreader adjustment valve set too low. Adjust.
Atomizing pressure too low. Increase pressure.
Material too thick. Thin to proper consistency.
Split spray pattern
Atomization air pressure too high. Reduce at transformer or gun.
Fluid pressure too low (pressure feed only). Increase fluid pressure (increases gun handling
speed).
Spreader adjusting valve set too high. Adjust.
Jerky or fluttering spray
*Loose or damaged fluid tip/seat. Tighten or replace.
Material level too low. Refill.
Container tipped too far. Hold more upright.
Obstruction in fluid passage. Backflush with solvent.
Loose or broken fluid tube or fluid inlet nipple. Tighten or replace.
Dry or loose fluid needle packing nut. Lubricate or tighten.
Unable to get round spray
Spreader adjustment screw not seating properly. Clean or replace.
Air cap retaining ring loose. Tighten.
Will not spray
No air pressure at gun. Check air supply and air lines.
Internal mix or pressure feed air cap and tip Change to proper suction feed air cap and tip.
used with suction feed.
Fluid pressure too low with internal mix cap Increase fluid pressure at tank.
and pressure tank.
Fluid needle adjusting screw not open enough. Open fluid needle adjusting screw.
Fluid too heavy for suction feed. Thin material or change to pressure feed.
Starved spray pattern
Inadequate material flow. Back fluid adjusting screw out to first thread
or increase fluid pressure at tank.
Low atomization air pressure (suction feed). Increase air pressure and rebalance gun.
Excessive overspray
Too much atomization air pressure Reduce pressure.
Gun too far from work surface. Adjust to proper distance.
Improper stroking (arcing, gun motion too fast). Move at moderate pace, parallel to work
surface.
Excessive fog
Too much, or too fast-drying thinner. Remix properly.
Too much atomization air pressure. Reduce pressure.
Dry Spray
Air pressure too high. Reduce air pressure.
Gun tip too far from work surface. Adjust to proper distance.
Gun motion too fast. Slow down.
Gun out of adjustment. Adjust.
Fluid leaking from
Packing nut loose. Tighten, do not bind needle.
packing nut
Packing worn or dry. Replace or lubricate.
Fluid leaking or dripping Packing nut too tight. Adjust
from front of pressure Dry packing. Lubricate.
feed gun Fluid tip or needle worn or damaged. Replace tip and needle with lapped sets.
Foreign matter in tip. Clean.
Fluid needle spring broken. Replace.
Wrong size needle or tip. Replace.
*Most common problem.
EN
SB-2-252-R4 (3/2019) 7 / 8 www.carlisleft.com
NIOSH-Certified, for
respiratory protection
in atmospheres not
immediately dangerous
to life.
TGC-545 (Aluminum)
TLC-555 (Non-stick Lined)
81-820 S.S. 2 Qt. Drip-Free
Suction Cup
Provides greater
degree of control
over cup fluid
pressure.
Millennium 3000
Twin Cartridge
Paint Spray Respirator
KB-555 (Aluminum) &
KB-545-SS (S/S) 2 qt. Pressure
Feed Cup With Regulator
Cup has a unique, two position
valve which permits selection of
either a drip-free or conventional
open vent mode.
JGA-444 Fluid Tube
This tube combines the fluid and air hoses at gun
handle preventing dragging hoses over work, twisting
line and improving overall gun handling.
81-510
Stainless Steel Cup
1 Qt. pressure feed cup.
3/8" NPS (F), cam lock lid.
Requires KK-4980 air regulator
kit.
Quick Disconnect Approved for
HVLP Guns (Air)
High Flow Ball and Ring Type
HC-4419 1/4"
NPS(F)
HC-4699
1/4" NPT(M)
HC-1166
1/4" NPT(M)
HC-4700
1/4" NPT(F)
Enables user to control
and reduce air usage at
the gun. Ideal for low
pressure spraying.
P-H-5516 Air
Adjusting Valve
HARG-510 Air
Regulator
Use to maintain nearly
constant outlet pressure
despite changes in
inlet pressure and
downstream flow.
HD-503
SolventSaver™
Hose/Gun Cleaner
Used when abrasive
materials are sprayed
(i.e. porcelain enamel).
Use (2) JGA-52 packings
in place of JGV-463
packing.
JGA-52-K10
Leather Packings
VS-531 Low
Pressure
Strainers
83GZ-5200
SolventSaver™
Hose/Gun Cleaner
GTI-415 Air
Adjusting Valve
Installs into gun to
enable user to control
and reduce air usage
at the gun. Replaces
JGA-132 plug.
Spray Gun Lube
SSL-10 (2 oz.
bottle)
Compatible with all
paint materials:
contains no silicone or
petroleum distillates
to contaminate paint.
MSDS sheet available
upon request.
2 Qt Hose/Gun Cleaner
used to clean the
inside of hose, fluid
passageways of gun &
other paint equipment.
The VS-531 Low
Pressure Fluid Strainer
provides a final filter
for trapping foreign
particles in the paint
supply.
2 Gallon galvanized tank
used to clean the inside
of hose and material
passages of the gun.
ACCESSORIES
Provides reduced
spring force (4 lbs.
verses 6 lbs.) for easier
trigger pull.
MSA-4-K10 Fluid
Needle Spring
(replaces MBD-19)
Joins any single piece
DeVilbiss air cap MBC-
368 or MSA-1 retaining
ring. Helps prevent
parts loss and provides
easier assembly.
JGA-156-K10
Spring Clip
HAF-507
Whirlwind™
In-Line Air Filter
Removes water, oil, and
debris from the air line.
This 3 piece packing
can be used in place
of Ref. (18) JGV-463, 2
piece packing.
JGA-4035-K5
Optional 3 Piece
Packings
HAV-500 or
HAV-501
Adjusting Valve
(HAV-501 SHOWN)
HAV-500 does not have
pressure gage. Use to
control air usage at gun.
42884-214-K5 3/8"
42884-215-K10 5/8"
Cleaning Brushes
These brushes are
helpful in cleaning
threads and recesses
of gun body.
WR-103 Wrench
Contains all necessary
tip, hose and nut sizes
used on or with gun.
Scrubs® are a pre-
moistened hand cleaner
towel for painters.
No water is needed.
29-3100 Scrubs®
Hand Cleaner Towels
JGA-191-K2
Heavy Duty
Spring
(for zinc rich
materials)
TROUBLESHOOTING (continued)
CONDITION CAUSE CORRECTION
Runs and sags Too much material flow. Adjust gun or reduce fluid pressure.
Material too thin. Mix properly or apply light coats.
Gun tilted on an angle, or gun motion Hold gun at right angle to work and adapt to
too slow. proper gun technique.
Thin, sandy coarse finish Gun too far from surface. Check distance. Normally approximately 8".
drying before it flows out Too much air pressure. Reduce air pressure and check spray pattern.
Improper thinner being used. Follow paint manufacturer's mixing instructions.
Thick, dimpled finish Gun too close to surface. Check distance. Normally approximately 8".
"orange peel". Too much material coarsely atomized. Increase air pressure or reduce fluid pressure.
Air pressure too low. Increase air pressure or reduce fluid pressure.
Improper thinner being used. Follow paint manufacturer's mixing instructions.
Material not properly mixed. Follow paint manufacturer's mixing instructions.
Surface rough, oily, dirty. Properly clean and prepare surface.
EN
SB-2-252-R4 (3/2019)8 / 8www.carlisleft.com
WARRANTY POLICY
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Carlisle Fluid Technologies,
will void all warranties. Failure to reasonably follow any maintenance guidance provided
may invalidate any warranty.
For specic warranty information please contact Carlisle Fluid Technologies.
For technical assistance or to locate an authorized distributor,
contact one of our international sales and customer support locations.
Region Industrial/Automotive Automotive Renishing
Americas Tel: 1-800-992-4657 Tel: 1-800-445-3988
Fax: 1-888-246-5732 Fax: 1-800-445-6643
Europe, Africa,
Middle East, India
Tel: +44 (0)1202 571 111
Fax: +44 (0)1202 573 488
China Tel: +8621-3373 0108
Fax: +8621-3373 0308
Japan Tel: +81 45 785 6421
Fax: +81 45 785 6517
Australia Tel: +61 (0) 2 8525 7555
Fax: +61 (0) 2 8525 7575
Carlisle Fluid Technologies is a global leader in innovative nishing technologies.
Carlisle Fluid Technologies reserves the right to modify equipment specications without prior notice.
DeVilbiss®, Ransburg®, ms®, BGK®, and Binks®
are registered trademarks of Carlisle Fluid Technologies, Inc.
©2019 Carlisle Fluid Technologies, Inc.
All rights reserved.
For the latest information about our products, visit www.carlisleft.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Carlisle JGA & JGHV Spray Gun Series User manual

JGA & JGHV Spray Gun Series
Carlisle
Brand
Carlisle
Model
JGA & JGHV Spray Gun Series
Category
Paint Sprayer
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents