Moen DN3624ORB User manual

Moen
Brand
Moen
Model
DN3624ORB
Type
User manual

This manual is also suitable for

Moen DN3624ORB is a 24-inch towel bar with an oil rubbed bronze finish. It is made from the highest quality zinc alloy (Zamac) and plated in oil rubbed bronze. The towel bar is aluminum.

The DN3624ORB is easy to install. Simply position the mounting template on the wall in the desired location, using a level to align the template and tape it to the wall. Drill two 5/16” holes at each mounting post location that corresponds to your product. Remove the template from the wall, fold ends of the plastic toggle together and insert into each hole in the wall. Lightly tap anchors until flush with the wall. One at a time, insert plastic pin into each of the anchors and lightly tap to activate anchor. Remove pin and repeat on all anchors.

Moen DN3624ORB is a 24-inch towel bar with an oil rubbed bronze finish. It is made from the highest quality zinc alloy (Zamac) and plated in oil rubbed bronze. The towel bar is aluminum.

The DN3624ORB is easy to install. Simply position the mounting template on the wall in the desired location, using a level to align the template and tape it to the wall. Drill two 5/16” holes at each mounting post location that corresponds to your product. Remove the template from the wall, fold ends of the plastic toggle together and insert into each hole in the wall. Lightly tap anchors until flush with the wall. One at a time, insert plastic pin into each of the anchors and lightly tap to activate anchor. Remove pin and repeat on all anchors.

Towel Bar
post is die cast from
the
highest quality zinc alloy (Zamac).
Casting is plated in chrome, brushed
nickel or oil rubbed bronze. Towel
bar is aluminum for brushed nickel
and chrome finishes and brass for oil
rubbed bronze.
§
DN3618BN
–
18” Towel
Bar
Brushed Nickel
§ DN3624BN – 24” Towel Bar
Brushed Nickel
§ DN3618CH – 18” Towel Bar
Chrome Finish
§ DN3624CH – 24” Towel Bar
Chrome Finish
§ DN3618ORB – 18” Towel Bar
Oil Rubbed Bronze
§ DN3624ORB – 24” Towel Bar
Oil Rubbed Bronze
Cleaning Instructions:
Stock Number:
18” & 24” Tow
el Bar
By Creative Specialties
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
18” & 24” Towel Bar
DN3618 & DN3624
Bradshaw™ Technical Specification
To preserve the fine finish of this product, clean only with a soft
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
25300 AL MOEN DRIVE
•
NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: (800) 321-8809 • FAX: (800) 848-6636
INTERNATIONAL: (440) 962-2000 • FAX: (440) 962-2726
CUSTOMER SERVICE (USA): 800-882-0116 • FAX: (888) 379-2720
WWW.CSI.MOEN.COM
Copyright Creative Specialties International 2006 Literature # BA1510
1. Position the mounting template on the wall in the desired location.
2. Using a level, align the template and tape it to the wall.
3. Drill two 5/16” holes at each mounting post location that corresponds to your
product.
4. Remove the template from the wall.
5. Fold ends of the plastic toggle together and insert into each hole in the wall.
6. Lightly tap anchors until flush with the wall.
7. One at a time, insert plastic pin into each of the anchors and lightly tap to
activate anchor. Remove pin and repeat on all anchors.
8. Remove mounting posts from the product assemblies by loosening each
setscrew.
9. Place the mounting plate on the wall over the installed wall anchors with “UP”
facing you.
10. Insert screws through the mounting plate into the anchors. Tighten the
screws.
11. Assemble the towel bar and posts.
12. While assembled, position each end post with setscrews facing down and
place over both mounting posts. Tighten the setscrew at the bottom of each
post.
  • Page 1 1

Moen DN3624ORB User manual

Moen
Brand
Moen
Model
DN3624ORB
Type
User manual
This manual is also suitable for

Moen DN3624ORB is a 24-inch towel bar with an oil rubbed bronze finish. It is made from the highest quality zinc alloy (Zamac) and plated in oil rubbed bronze. The towel bar is aluminum.

The DN3624ORB is easy to install. Simply position the mounting template on the wall in the desired location, using a level to align the template and tape it to the wall. Drill two 5/16” holes at each mounting post location that corresponds to your product. Remove the template from the wall, fold ends of the plastic toggle together and insert into each hole in the wall. Lightly tap anchors until flush with the wall. One at a time, insert plastic pin into each of the anchors and lightly tap to activate anchor. Remove pin and repeat on all anchors.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents