Heatilator NNXT3933IF-B Installation guide

Brand: Heatilator

Model: NNXT3933IF-B

Category: Fireplaces

Type: Installation guide

This manual is also suitable for

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

Installation Manual

Installation and Appliance Setup

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT discard this manual!

In the Commonwealth of Massachusetts installation must be

performed by a licensed plumber or gas tter.

See Table of Contents for location of additional Commonwealth

of Massachusetts requirements.

Models:

This appliance may be installed as an OEM

installation in manufactured home (USA

only) or mobile home and must be installed

in accordance with the manufacturer’s

instructions and the Manufactured Home

Construction and Safety Standard, Title 24

CFR, Part 3280 in the United States, or the

Standard for Installation in Mobile Homes,

CAN/CSA Z240 MH Series, in Canada.

This appliance is only for use with the type(s)

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certied kit is used.

• DO NOT store or use gasoline or other am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Leave the building immediately.

- Immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions.

- If you cannot reach your gas supplier, call

the re department.

• Installation and service must be performed

by a qualied installer, service agency, or the

gas supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided

with this appliance and shall be installed for

the protection of children and other at-risk

individuals.

NNXT4236IF-B

NNXT4236ILF-B

NNXT3933IF-B

NNXT3933ILF-B

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

Installation Standard Work Checklist ....................3

1 Product Specic and Important Safety Information

A. Appliance Certication ............................4

B. Glass Specications ..............................4

C. BTU Specications ...............................4

D. High Altitude Installations .......................... 4

E. Non-Combustible Materials Specication. . . . . . . . . . . . . . 4

F. Combustible Materials Specication .................4

G. Electrical Codes .................................4

H. Requirements for the Commonwealth of Massachusetts . . 5

2 Getting Started

A. Design and Installation Considerations ...............6

B. Wall Surface/TV Guidelines ........................6

C. Tools and Supplies Needed ........................6

D. Inspect Appliance and Components ..................6

3 Framing and Clearances

A. Appliance/Decorative Front Dimension Diagrams .......7

B. Clearances to Combustibles ...................... 11

C. Constructing the Appliance Chase .................. 13

4 Termination Location and Vent Information

A. Vent Termination Minimum Clearances ..............14

B. Chimney Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

C. Approved Pipe ................................. 16

D. Use of Elbows .................................17

E. Measuring Standards ............................18

F. Vent Diagrams .................................19

5 Vent Clearances and Framing

A. Pipe Clearances to Combustibles ..................31

B. Wall Penetration Framing/Firestops .................32

C. Ceiling Firestop/Floor Penetration Framing ...........33

D. Install Attic Insulation Shield .......................33

6 Appliance Preparation

A. Top Vent ......................................34

B. Rear Vent .....................................35

C. Securing and Leveling the Appliance ................ 36

7 Venting and Chimneys

A. Assemble Vent Sections .........................37

B. Assemble Slip Sections .......................... 38

C. Secure the Vent Sections .........................39

D. Disassemble Vent Sections .......................39

E. Vertical Termination Requirements ..................40

F. Horizontal Termination Requirements ...............41

G. HHT Shrouds ..................................43

8 Electrical Information

A. General Information .............................45

B. Wiring Requirements ............................45

9 Gas Information

A. Fuel Conversion ................................47

B. Gas Pressure ..................................47

C. Gas Connection ................................47

D. High Altitude Installations ......................... 47

E. Air Shutter Setting ..............................48

10 Finishing

A. Facing Material .................................49

B. Mantel and Wall Projections .......................49

C. Decorative Front Dimensions for Finishing ...........50

11 Appliance Setup

A. Remove the Packaging ..........................51

B. Remove the Shipping Materials ....................51

C. Removing Fixed Glass Assembly ...................51

D. Remove Packing Material ........................51

E. Clean the Appliance .............................51

F. Install Logs ....................................52

G. Place the Mineral Wool ..........................54

H. Place the Lava Rock ............................55

I. Place the Vermiculite ............................55

J. Install Control Heat Shield ........................55

K. Install Fixed Glass Assembly ......................55

L. Install Decorative Front .......................... 55

12 Reference Materials

A. Vent Components Diagrams ......................56

B. Optional Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

C. Accessories ...................................67

 = Contains updated information.



Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

Installation Standard Work Checklist

Appliance Install Sections 3 and 6 YES IF NO, WHY?

Veri ed that the chase is insulated and sealed. (Pg. 13) ___________________________

Veri ed factory-installed non-combustible board is in place. ___________________________

Veri ed clearances to combustibles. (Pg. 11, 12) ___________________________

Fireplace is leveled and secured. (Pg. 36) ___________________________

Venting/Chimney Section 4,5 and 7

Venting con guration complies to vent diagrams. (Pg. 19-30) ___________________________

Venting installed, locked and secured in place with proper clearance. ___________________________

Firestops installed. (Section 5) ___________________________

Attic insulation shield installed. (Pg. 33) ___________________________

Exterior wall/Roof  ashing installed and sealed. (Section 7) ___________________________

Terminations installed and sealed. (Section 7) ___________________________

Electrical Section 8 (Pg. 45-46)

Unswitched power (110-120 VAC) provided to the appliance. ___________________________

Switch wires properly installed. ___________________________

Gas Section 9 (Pg. 47-48)

Proper appliance for fuel type. ___________________________

Was a conversion performed? ___________________________

Leak check performed and inlet pressure veri ed. ___________________________

Veri ed proper air shutter setting for installation type. ___________________________

Finishing Section 10 (Pg. 49-50)

Combustible materials not installed in non-combustible areas. ___________________________

Veri ed all clearances meet installation manual requirements. ___________________________

Mantels and wall projections comply with installation manual requirements. ___________________________

Appliance Setup Section 11 (Pg. 51-55)

All packaging and protective materials removed (inside & outside of appliance). ___________________________

Refractories, logs, mineral wool, lava rock and vermiculite installed correctly. ___________________________

Glass assembly installed and secured. ___________________________

Accessories installed properly. ___________________________

Decorative front properly installed. ___________________________

Manual bag and all of its contents are removed from inside/under

the appliance and given to party responsible for use and operation. ___________________________

Started appliance and veri ed no gas leaks exist. ___________________________

Customer:

Lot/Address:

Model (circle one): NNXT4236IF-B NNXT3933IF-B

Name NNXT4236ILF-B NNXT3933ILF-B

Date Installed:

Location of Fireplace:

Installer:

Dealer/Distributor Phone #

Serial #:

Comments: Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective

action needed _____________________________________________________________________________________

_________________________________________________________________________________________________

Comments Communicated to party responsible ____________________ by ______________________on ___________

(Builder / Gen. Contractor/) (Installer) (Date)

2384-982 Rev. B 6/16

 = Contains updated information.

Hearth & Home Technologies recommends the following:

• Photographing the installation and copying this checklist for your  le.

• That this checklist remain visible at all times on the appliance until the installation is complete.

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this

installation manual.

WARNING! Risk of Fire or Explosion! Failure to install appliance according to these instructions could

lead to a  re or explosion.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

C. BTU Specications

E. Non-Combustible Materials Specication

Material which will not ignite and burn. Such materials are

those consisting entirely of steel, iron, brick, tile, concrete,

slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in

a Vertical Tube Furnace at 750 ºC shall be considered

non-combustible materials.

F. Combustible Materials Specication

Materials made of or surfaced with wood, compressed pa-

per, plant bers, plastics, or other material that can ignite

and burn, whether ame proofed or not, or plastered or

unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired

and grounded in accordance with local codes or, in the

absence of local codes, with National Electric Code

ANSI/NFPA 70-latest edition or the Canadian Electric

Code CSA C22.1.

• A 110-120 VAC circuit for this product must be pro-

tected with ground-fault circuit-interrupter protection,

in compliance with the applicable electrical codes,

when it is installed in locations such as in bathrooms

or near sinks.

1 Product Specic and Important Safety Information

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced,

these rules do not apply. Check with your local gas utility

or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet

above 2000 feet.

• In CANADA: Input ratings are certied without a

reduction of input rate for elevations up to 4500 feet

(1370 m)above sea level. Please consult provincial and/

or local authorities having jurisdiction for installations at

elevations above 4500 feet (1370 m).

Check with your local gas utility to determine proper

orice size.

A. Appliance Certication

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemen-

tal room heat or as a decorative appliance. It should not be

factored as primary heat in residential heating calculations.

NOTICE: This installation must conform with local codes.

In the absence of local codes you must comply with the

National Fuel Gas Code, ANSI Z223.1-latest edition in

the U.S.A. and the CAN/CGA B149 Installation Codes in

Canada.

B. Glass Specications

This appliance is equipped with 5 mm ceramic glass. Re-

place glass only with 5 mm ceramic glass. Please contact

your dealer for replacement glass.

This product is listed to ANSI standards for “Vented Gas

Fireplace Heaters” and applicable sections of “Gas Burn-

ing Heating Appliances for Manufactured Homes and

Recreational Vehicles”, and “Gas Fired Appliances for

Use at High Altitudes”.

MODELS: NNXT4236IF-B, NNXT4236ILF-B,

NNXT3933IF-B, NNXT3933ILF-B

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Heater

STANDARD: ANSI Z21.88-2014/CSA 2.33-2014

Models

(U.S. or Canada)

Maximum

Input BTU/h

Minimum

Input

BTU/h

Orice

Size

NNXT3933IF-B

(NG) (0-2000 FT) 29,000 16,000 #39 DMS

NNXT3933ILF-B

(Propane) (0-2000 FT) 28,000 15,750 1.55 mm

NNXT4236IF-B

(NG) (0-2000 FT) 31,000 18,500 #37 DMS

NNXT4236ILF-B

(Propane) (0-2000 FT) 29,000 15,500 #52 DMS

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

H. Requirements for the Commonwealth of

Massachusetts

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in

whole or in part for residential purposes, including those

owned or operated by the Commonwealth and where the

side wall exhaust vent termination is less than seven (7)

feet above nished grade in the area of the venting, in-

cluding but not limited to decks and porches, the following

requirements shall be satised:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented

gas fueled equipment, the installing plumber or gas tter

shall observe that a hard wired carbon monoxide detector

with an alarm and battery back-up is installed on the oor

level where the gas equipment is to be installed. In addi-

tion, the installing plumber or gas tter shall observe that

a battery operated or hard wired carbon monoxide detec-

tor with an alarm is installed on each additional level of

the dwelling, building or structure served by the side wall

horizontal vented gas fueled equipment. It shall be the

responsibility of the property owner to secure the services

of qualied licensed professionals for the installation of

hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fu-

eled equipment is installed in a crawl space or an attic,

the hard wired carbon monoxide detector with alarm and

battery back-up may be installed on the next adjacent

oor level.

In the event that the requirements of this subdivision can

not be met at the time of completion of installation, the

owner shall have a period of thirty (30) days to comply

with the above requirements; provided, however, that dur-

ing said thirty (30) day period, a battery operated carbon

monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accor-

dance with the above provisions shall comply with NFPA

720 and be ANSI/UL 2034 listed and IAS certied.

Signage

A metal or plastic identication plate shall be permanent-

ly mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with the

exhaust vent terminal for the horizontally vented gas fu-

eled heating appliance or equipment. The sign shall read,

in print size no less than one-half (1/2) in. in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-

STRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizon-

tally vented gas fueled equipment shall not approve the

installation unless, upon inspection, the inspector ob-

serves carbon monoxide detectors and signage installed

in accordance with the provisions of 248 CMR 5.08(2)(a)1

through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)

(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition

of NFPA 54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas fu-

eled equipment installed in a room or structure separate

from the dwelling, building or structure used in whole or

in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall

horizontally vented gas equipment provides a venting

system design or venting system components with the

equipment, the instructions provided by the manufacturer

for installation of the equipment and the venting system

shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall

horizontally vented gas fueled equipment does not pro-

vide the parts for venting the ue gases, but identies

“special venting systems”, the following requirements

shall be satised by the manufacturer:

• The referenced “special venting system” instructions

shall be included with the appliance or equipment in-

stallation instructions; and

• The “special venting systems” shall be Product Ap-

proved by the Board, and the instructions for that sys-

tem shall include a parts list and detailed installation

instructions.

A copy of all installation instructions for all Product Ap-

proved side wall horizontally vented gas fueled equip-

ment, all venting instructions, all parts lists for venting

instructions, and/or all venting design instructions shall

remain with the appliance or equipment at the completion

of the installation.

See Gas Connection section for additional Common-

wealth of Massachusetts requirements.

Note: The following requirements reference various

Massachusetts and national codes not contained in this

document.

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

2 Getting Started

A. Design and Installation Considerations

Heatilator direct vent gas appliances are designed to op-

erate with all combustion air siphoned from outside of the

building and all exhaust gases expelled to the outside. No

additional outside air source is required.

Installation MUST comply with local, regional, state and

national codes and regulations. Consult insurance carrier,

local building inspector, re ofcials or authorities having

jurisdiction over restrictions, installation inspection and

permits.

Before installing, determine the following:

• Where the appliance is to be installed.

• The vent system conguration to be used.

• Gas supply piping requirements.

• Electrical wiring requirements.

• Framing and nishing details.

• Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

D. Inspect Appliance and Components

• Carefully remove the appliance and components from

the packaging.

• The vent system components and decorative doors and

fronts may be shipped in separate packages.

• If packaged separately, the log set and appliance grate

must be installed.

• Report to your dealer any parts damaged in shipment,

particularly the condition of the glass.

• Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the

installation to ensure maximum safety and benet.

WARNING! Risk of Fire or Explosion! Damaged parts

could impair safe operation. DO NOT install damaged, in-

complete or substitute components. Keep appliance dry.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following

tools and building supplies are available.

Tape measure Framing material

Pliers Hammer

Phillips screwdriver Manometer

Gloves Framing square

Voltmeter Electric drill and bits (1/4 in.)

Plumb line Safety glasses

Level Reciprocating saw

Flat blade screwdriver

Non-corrosive leak check solution

1/2 - 3/4 in. length, #6 or #8 Self-drilling screws

Caulking material (300ºF minimum continuous exposure

rating)

One 1/4 in. female connection (for fan).

Hearth & Home Technologies disclaims any responsibility for,

and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance or vent

system component.

• Modication of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a re hazard.

WARNING! Risk of Fire, Explosion or Electric Shock!

DO NOT use this appliance if any part has been under

water. Call a qualied service technician to inspect the

appliance and to replace any part of the control system

and/or gas control which has been under water.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualied

service technician, service agency or your dealer.

Figure 2.1 Maximum Wall Surface Temperatures Above Appliance

B. Wall Surface/TV Guidelines

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

6 in.

18 in.

24 in.

30 in.

36 in.

48 in.

TO CEILING

42 in.

12 in.

123°F

115°F

120°F

132°F

145°F

170°F

180°F

APPLIANCE FRONT

APPLIANCE OPENING

110°F

NOTICE: Temperatures listed above are taken with a

temperature measuring probe as prescribed by the test

standard used for appliance certication. Temperatures

on walls or mantels taken with an infrared thermometer

may yield increased temperatures of up to 30 degrees or

more depending on the thermometer settings and material

characteristics being measured.

Installation and service of this appliance should be performed by

qualied personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certied professionals.

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

3 Framing and Clearances

A. Appliance/Decorative Front Dimension Diagrams

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

Figure 3.1 Appliance Dimensions - NNXT3933IF-B, NNXT3933ILF-B, NNXT4236IF-B, NNXT4236ILF-B

Appliance Dimensions Table

NNXT3933IF-B/NNXT3933ILF-B NNXT4236IF-B/NNXT4236ILF-B

Location Inches Millimeters Inches Millimeters

A38 965 41 1041

B33 838 36 916

C6-3/8 162 6-3/8 162

D19-7/8 505 19-7/8 505

E29-5/8 752 32-5/8 829

F31-1/2 800 31-1/2 800

G35-1/4 896 35-1/4 896

H15-3/4 400 15-3/4 400

I1-3/4 44 1-3/4 44

J23-1/2 597 23-1/2 597

K39-1/2 1003 39-1/2 1003

L3 76 3 76

M6-1/2 165 mm 6-1/2 165

N34-1/2 876 34-1/2 876

O11-5/8 295 14-5/8 371

P5-7/8 148 7-3/8 186

Q11-1/2 292 11-1/2 292

R19-1/8 486 19-1/8 486

S2-3/8 60 2-3/8 60

T8 203 8 203

GAS LINE

ACCESS

DEF

ELECTRICAL

ACCESS

ALTERNATE

GAS ACCESS

MEASURE TO TOP OF STANDOFF

C VENT

OPENING

C VENT OPENING

C VENT

OPENING

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

Figure 3.2 Decorative Front Dimensions - DEMI-B

DEMI-B DECORATIVE FRONTS

A B C D E F G

DEMI-3630-B in. 26-7/8 20-3/8 29-7/8 1-7/8 6-3/4 30 31-7/8

mm 683 518 759 48 171 762 810

DEMI-3933-B in. 29-7/8 20-3/8 32-7/8 1-7/8 6-3/4 30 31-7/8

mm 759 518 835 48 171 762 810

DEMI-4236-B in. 32-7/8 20-3/8 35-7/8 1-7/8 6-3/4 30 31-7/8

mm 835 518 911 48 171 762 810

DEMI-4842-B in. 38-7/8 20-3/8 41-7/8 1-7/8 6-3/4 30 31-7/8

mm 987 518 1064 48 171 762 810

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

TRES-B DECORATIVE FRONTS

Figure 3.3 Decorative Front Dimensions - TRES-B

A B C D E F G

TRES-3630-B in. 26-7/8 19-7/8 29-7/8 1-7/8 6-3/4 30 31-7/8

mm 683 505 759 48 171 762 810

TRES-3933-B in. 29-7/8 19-7/8 32-7/8 1-7/8 6-3/4 30 31-7/8

mm 759 505 835 48 171 762 810

TRES-4236-B in. 32-7/8 19-7/8 35-7/8 1-7/8 6-3/4 30 31-7/8

mm 835 505 911 48 171 762 810

TRES-4842-B in. 38-7/8 19-7/8 41-7/8 1-7/8 6-3/4 30 31-7/8

mm 987 505 1064 48 171 762 810

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

SIMON DECORATIVE FRONTS

A B C D E F G

SIM-3630 in. 28-3/8 21 29-7/8 1-5/8 6-3/4 28 29-5/8

mm 721 533 759 41 171 711 753

SIM-3933 in. 31-3/8 21 32-7/8 1-5/8 6-3/4 28 29-5/8

mm 797 533 835 41 171 711 753

SIM-4236 in. 34-3/8 21 35-7/8 1-5/8 6-3/4 28 29-5/8

mm 873 533 911 41 171 711 753

SIM-4842 in. 40-3/8 21 41-7/8 1-5/8 6-3/4 28 29-5/8

mm 1026 533 1064 41 171 711 753

Figure 3.4 Decorative Front Dimensions - SIMON-B

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

In addition to these framing dimensions, also reference

the following sections:

• Clearances and Mantel Projections

• Vent Clearances and Framing

Rear Vent

Two 90° elbows

Horiz Term

Rear Vent

One 90° elbow

Vert Term

Top Vent

One 90° elbow

Horiz Term

1/2 in. (13 mm)

min. appliance

to combustibles

Alcove

Installation

1 in. (25 mm)

min. pipe to

combustibles

Drywall

48 in.

(1219 mm)

maximum

* As B increases, L increases accordingly.

B. Clearances to Combustibles

When selecting a location for the appliance it is important

to consider the required clearances to walls (see Figure

3.5).

WARNING! Risk of Fire or Burns! Provide adequate

clearance around air openings and for service access.

Due to high temperatures, the appliance should be lo-

cated out of trafc and away from furniture and draperies.

NOTICE: Illustrations reect typical installations and are

FOR DESIGN PURPOSES ONLY. Illustrations/diagrams

are not drawn to scale. Actual installation may vary due to

individual design preference.

Figure 3.5 Appliance Locations

A B C D E F G H I J

NNXT3933IF-B in 39 35-1/2 19-5/8 47 53-1/4 40 50-1/4 66-1/2 75-3/8 9-1/2

mm 991 902 498 1194 1353 1016 1276 1689 1915 241

NNXT4236IF-B in 42 37-5/8 19-5/8 47 53-1/4 43 53-1/4 66-1/2 75-3/8 10-5/8

mm 1067 956 498 1194 1353 1092 1353 1689 1915 270

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

Figure 3.6 Clearances to Combustibles

Note: If the inside of the framed cavity is to be nished,

the framing dimensions must include the finished

surface. If drywall is to be attached to the rear wall,

the depth must be measured from the drywall surface.

Clearance to Ceiling

30 in. (762 mm)

0 in.

0 in. to level

of standoffs

Combustible Object

36 in.

(914 mm)

0 in.

Combustible flooring may be installed next

to the front of the appliance.

Drywall

1/2 in.

(13 mm)

1/2 in.

(13 mm)

* MINIMUM FRAMING DIMENSIONS

NDV MODEL

(LP/NG)

A B C** D D

Rough

Opening

(Width)

Rough

Opening

(Height)

Rough

Opening

(Depth)

Rough

Opening

(DVP Pipe)

Rough

Opening

(SLP Pipe)

3933 in. 39 34-7/8 19-5/8 10 9

mm 991 886 498 254 229

4236 in. 42 34-7/8 19-5/8 10 9

mm 1067 886 498 254 229

NO COMBUSTIBLES

IN THIS AREA

2 X 4 OR 2 X 6 FRAMING

COMBUSTIBLE

FRAMING

FOR MANTEL AND WALL

PROJECTIONS SEE SECTION 10.B

NON-COMBUSTIBLE

FACING MATERIAL

THICKNESS =

1/2 IN. MIN.

4 IN. MAX.

TOP OF FIREPLACE OPENING

FINISH WALL

COMBUSTIBLE

PIPE LENGTH VARIES PER APPLICATION

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

C. Constructing the Appliance Chase

A chase is a vertical box-like structure built to enclose the

gas appliance and/or its vent system. In cooler climates

the vent should be enclosed inside the chase.

NOTICE: Treatment of ceiling restops and wall shield

restops and construction of the chase may vary with the

type of building. These instructions are not substitutes

for the requirements of local building codes. Therefore,

you MUST check local building codes to determine the

requirements to these steps.

Chases should be constructed in the manner of all out-

side walls of the home to prevent cold air drafting prob-

lems. The chase should not break the outside building

envelope in any manner.

Walls, ceiling, base plate and cantilever oor of the chase

should be insulated. Vapor and air inltration barriers

should be installed in the chase as per regional codes for

the rest of the home. Additionally, in regions where cold

air inltration may be an issue, the inside surfaces may be

sheetrocked and taped (or an equivalent method may be

used) to achieve maximum air tightness.

NOTICE: Install appliance on hard metal or wood surfaces

extending full width and depth. DO NOT install directly

on carpeting, vinyl, tile or any combustible material other

than wood.

WARNING! Risk of Fire! Maintain specied air space

clearances to appliance and vent pipe:

• Insulation and other materials must be secured to prevent

accidental contact.

• The chase must be properly blocked to prevent blown

insulation or other combustibles from entering and

making contact with replace or chimney.

• Failure to maintain airspace may cause overheating and

a re.

To further prevent drafts, the wall shield and ceiling re-

stops should be caulked with caulk with a minimum of

300ºF continuous exposure rating to seal gaps. Gas

line holes and other openings should be caulked with

caulk with a minimum of 300 ºF continuous exposure rating

or stuffed with unfaced insulation. If the appliance is being

installed on a cement surface, a layer of plywood may be

placed underneath to prevent conducting cold up into the

room.

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

A. Vent Termination Minimum Clearances

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5*

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

Figure 4.1 Minimum Height From Roof to Lowest Discharge

Opening

HORIZONTAL

OVERHANG

VERTICAL

WALL

GAS DIRECT VENT

TERMINATION CAP

ROOF PITCH

IS X/ 12

LOWEST

DISCHARGE

OPENING

2 FT.

MIN.

20 INCHES MIN.

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

4 Termination Location and Vent Information

Fire Risk.

Maintain vent clearance to combustibles as

specied.

• DO NOT pack air space with insulation or other

materials.

Failure to keep insulation or other materials away

from vent pipe could cause overheating and re.

WARNING

Figure 4.2 Staggered Termination Caps

Gas, Wood or Fuel Oil

Termination Cap

Gas

Termination

Cap **

A *

*If using decorative cap cover(s), this distance may need to be

increased. Refer to the installation instructions supplied with the

decorative cap cover.

A B

6 in. (minimum) up to 20 in.

152 mm/508 mm

18 in. minimum

457 mm

20 in. and over 0 in. minimum

In a staggered installation with both gas and wood or fuel oil

terminations, the wood or fuel oil termination cap must be

higher than the gas termination cap.

* H minimum may vary depending on regional snowfall.

Refer to local codes.

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

B. Chimney Diagram

Figure 4.3 Minimum Clearances for Termination

X= AIR SUPPLY INLET

V= VENT TERMINAL

= AREA WHERE TERMINAL IS NOT PERMITTED

H or i

Electrical

Service

V K

N = 6 inches ........... non-vinyl sidewalls

12 inches ......... vinyl sidewalls

O = 18 inches ......... non-vinyl soft and overhang

42 inches ......... vinyl soft and overhang

P = 8 ft.

QMIN RMAX

1 cap 3 feet 2 x Q ACTUAL

2 caps 6 feet 1 x Q ACTUAL

3 caps 9 feet 2/3 x Q ACTUAL

4 caps 12 feet 1/2 x Q ACTUAL

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

Covered Alcove Applications

(Spaces open only on one side and with an overhang)

Measure horizontal clearances from this surface.

See Section 4.E Measuring Standards

CLEARANCE = 6 IN.

CAUTION! Risk of Burns! Termination caps are HOT,

consider proximity to doors, trafc areas or where people

may pass or gather (sidewalk, deck, patio, etc.). Listed cap

shields available. Contact your dealer.

• Local codes or regulations may require different

clearances.

• Vent system termination is NOT permitted in screened

porches.

• Vent system termination is permitted in porch areas with

two or more sides open.

• Hearth & Home Technologies assumes no responsibility

for the improper performance of the appliance when the

venting system does not meet these requirements.

• Vinyl protection kits are suggested for use with vinyl siding.

M = 12 inches ................... clearance under veranda, porch, deck,

balcony or overhang

30 inches ...............vinyl or composite overhang

Permitted when veranda, porch, deck or balcony is fully open

on a minimum of 2 sides beneath the oor.

K = 6 inches................. clearance from sides of electrical

service

L = 12 inches................ clearance above electrical service

Location of the vent termination must not interfere with access to the

electrical service.

A = 12 inches.................clearances above grade, veranda,

porch, deck or balcony

B = 9 inches...................clearance to window or door that may

be opened, or to permanently closed

window

C = 12 inches.................clearance below unventilated soft

18 inches.................clearance below ventilated soft

30 inches ................clearance below vinyl soffits and

electrical service

D = 6 inches...................clearance to outside corner

E = 6 inches...................clearance to inside corner

F = 3 ft. (Canada) ..........not to be installed above a gas me-

ter/regulator assembly within 3 feet

horizontally from the center-line of the

regulator

G = 3 ft ...........................clearance to gas service regulator

vent outlet

H = 9 inches ((U.S.A)

12 inches (Canada) . . clearance to non-mechanical (unpow-

ered) air supply inlet, combustion air

inlet or direct-vent termination

I = 3 ft. above if within 10ft.

horizontally…..clearance to a mechanical air supply inlet

= 6 ft. (Canada)

All mechanical air intakes within 10 feet of a termination cap

must be a minimum of 3 feet below termination.

J = 7 ft. ......................... On public property: clearance above

paved sidewalk or a paved driveway.

A vent shall not terminate directly above a sidewalk or paved

driveway which is located between two single family dwellings

and serves both dwellings.

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

C. Approved Pipe

This appliance is approved for use with Hearth & Home

Technologies DVP or SLP venting systems. Refer to Sec-

tion 12.A for vent component information and dimensions.

DO NOT mix pipe, ttings or joining methods from differ-

ent manufacturers.

The pipe is tested to be run inside an enclosed wall.

There is no requirement for inspection openings at each

joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appli-

ance requires a separate vent. DO NOT vent to a pipe

serving a separate solid fuel burning appliance.

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

D. Use of Elbows

Diagonal runs have both vertical and horizontal vent as-

pects when calculating the effects. Use the rise for the

vertical aspect and the run for the horizontal aspect. See

Figure 4.4.

Two 45º elbows may be used in place of one 90º elbow.

On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216

mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A

length of straight pipe is allowed between two 45º elbows.

See Figure 4.4.

Figure 4.5 shows the vertical and horizontal offsets for

DVP or SLP elbows.

Figure 4.4

HORIZONTAL

VERTICAL

RUN

RISE

EFFECTIVE

LENGTH

DVP

Pipe

Effective Length Rise/Run

Inches Millimeters Inches Millimeters

DVP4 4 102 2-3/4 70

DVP6 6 152 4-1/4 108

DVP12 12 305 8-1/2 216

DVP24 24 610 17 432

DVP36 36 914 25-1/2 648

DVP48 48 1219 34 864

DVP6A 3 to 6 76 to 152 2-1/8-4-1/4 54-108

DVP12A 3 to 12 76 to 305 2-1/8-8-1/2 54-216

Vent Type X

Inches Millimeters

DVP 16-1/4 413

SLP 11-1/4 286

Figure 4.5 Vertical and Horizontal Offset for DVP and SLP Elbows

Vent

Type

X Y

Inches Millimeters Inches Millimeters

DVP 4-1/2 114 17 432

SLP 5 127 11-3/4 298

SLP

Pipe

Effective Length Rise/Run

Inches Millimeters Inches Millimeters

SLP4 4 102 2-3/4 70

SLP6 6 152 4-1/4 108

SLP12 12 305 8-1/2 216

SLP24 24 610 17 432

SLP36 36 914 25-1/2 648

SLP48 48 1219 34 864

SLP6A 3 to 6 76 to 152 2-1/8-4-1/4 54-108

SLP12A 3 to 12 76 to 305 2-1/8-8-1/2 54-216

Note: Back to back 45 degree or 90 degree elbows have

no additional vertical or horizontal value and are not in-

cluded in determining maximum vent run lengths.

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

E. Measuring Standards

Vertical and horizontal measurements listed in the vent

diagrams were made using the following standards:

• Pipe measurements are shown using the effective length

of pipe. See Section 12.A (Figure 12.1 for DVP, Figure

12.8 for SLP) for information on effective length of pipe

components.

• Horizontal terminations are measured to the outside

mounting surface (ange of termination cap) (see Figure

4.6).

• Vertical terminations are measured to top of last section

of pipe. See Figure 4.7.

• Horizontal pipe installed level with no rise.

MEASURE TO SHADED SURFACE

(OUTSIDE MOUNTING SURFACE)

Figure 4.6 Measure to Outside Mounting Surface

Figure 4.7. Measure to Top of Last Section of Pipe

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

F. Vent Diagrams

Figure 4.8 Water Inltration Prevention Tip

1/4 in. max.

(6 mm)

General Rules:

• Additional elbows: SUBTRACT 3 ft. from the total H

measurement for each 90º elbow installed horizontally.

• Additional elbows: SUBTRACT 1-1/2 ft. from the total H

measurement for each 45º elbow installed horizontally.

• A maximum of three 90º elbows (or six 45º elbows) may

be used in any vent conguration. Some elbows may be

installed horizontally.

• Elbows may be placed back to back anywhere in the

system.

• Any 90º elbow may be replaced with two back to back

45º elbows.

• When penetrating a combustible wall, a wall shield

restop must be installed.

• When penetrating a combustible ceiling, a ceiling restop

must be installed.

• Horizontal runs of vent do not require vertical rise;

horizontal runs may be level.

• When the horizontal termination cap is exposed to high

precipitation, the cap should have a 1/4 inch downward

slant to allow any moisture in cap to be released. See

Figure 4.8.

Heatilator • NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF-B Installation Manual • 2384-980 Rev. J • 6/17

Figure 4.10

Top Vent - Horizontal Termination

Top Vent—Horizontal Termination—Two 45º Elbows

Installation requirements to replace the rst 90º elbow

with two 45º elbows:

4 ft min.

(1.22 m)

25 ft max.

(7.62 m)

Figure 4.9 Minimum Installation Requirements for Two 45 Degree

Elbows - Top Vent - Horizontal Termination

Note: The NDV series appliances can adapt to SLP series

vent pipe when venting off the top of the appliance. You

must use a DVP-SLP24 adapter or a DVP-2SL and two feet

of SLP pipe which can only be attached to the appliance

starting collar.

When looking at horizontal termination diagrams, neither

adapter is counted as part of the minimum vertical (V1 min.)

requirements.

All venting rules for the vent run must still be followed.

H1 = 11 ft.

max.

V1 = 1 ft.

DVP PIPE

HORIZONTAL EXAMPLE

(IDENTICAL VENT RUNS USING DVP AND SLP PIPE)

H1 = 11 ft.

max.

DVP-SLP24

SLP PIPE

V1 = 1 ft.

2 ft. SLP

DVP-2SL

AND

DVP-SLP24

Adapter

6 ft (1.8 m) min.

60 ft (18.29 m) max.

12 ft (3.66 m) min.

60 ft (18.29 m) max.

DVP SLP

VERTICAL EXAMPLE

(IDENTICAL VENT RUNS USING DVP AND SLP PIPE)

2 ft. SLP

DVP-2SL

AND

Page is loading ...

Heatilator NNXT3933IF-B Installation guide

Brand: Heatilator

Model: NNXT3933IF-B

Category: Fireplaces

Type: Installation guide

This manual is also suitable for

Download PDF

report

Heatilator NNXT3933IF-B Installation guide

This manual is also suitable for

Heatilator NNXT3933IF-B Installation guide

Related papers

Other documents