8M-B120C Dismantle Instruction
1
Dismantle Instruction
LCD MONITOR
MODEL
8M-B120C
8M-B120C Dismantle Instruction
2
Table of contents
1. Scope ............................................................................................................... 3
2. Tools for dismantling............................................................................................. 3
3. Dismantle Procedure ............................................................................................ 3
4. Batteries ........................................................................................................... 4
5. Back covers ........................................................................................................ 4
6. Printed circuit boards ........................................................................................... 5
7. LCD Module bezels/angles ...................................................................................... 6
8. Capacitors .......................................................................................................... 7
9. Parts List ........................................................................................................... 7
8M-B120C Dismantle Instruction
3
1. Scope
This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU.
2. Tools for dismantling
Below tools are required to dismantle this product.
- Screw Driver
- Nipper
3. Dismantle Procedure
This product can be dismantled by below steps.
1. Remove battery (section 4)
2. Remove Back covers (section 5)
3. Remove Printed circuit boards (section 6)
4. Dismantle LCD (section 7)
5. Remove Electrolyte Capacitors (section 8)
8M-B120C Dismantle Instruction
4
4. Batteries
This model uses only AAA battery for remote control.
Battery can easily be removed.
5. Back covers
3 back covers (right/center/left) can be removed by screw driver.
8M-B120C Dismantle Instruction
5
6. Printed circuit boards
All PWBs can be removed by screw driver.
Main PWB (1pcs) Power PWB (4pcs) Back end PWB(1pcs)
Backlight Power Control PWB (1pcs) Main T-CON PWB (1pcs)
Sub T-CON PWB (8pcs) LED Driver PWB (4pcs) AC Detection PWB (1pcs)
8M-B120C Dismantle Instruction
6
7. LCD Module bezels/angles
- LCD Dismantle procedure
1. Remove screws (part 1)
2. Remove Corner Angle (part 9) and Bezels (part 8 and 10)
3. Remove screws (part 4 and 5)
4. Remove Middle Frame (Part 2, 3, 6, and 7)
LCD
8M-B120C Dismantle Instruction
7
8. Capacitors
Electrolyte Capacitors which diameter/height is larger than 25mm is installed on the Power PWB.
These capacitors can be removed by using nipper to cut the leads.
9. Parts List
Parts described in Annex VII of directive 2012/19/EU are as below.
Parts
Note
LCD
120inch LCD module
Batteries
Battery(AAA) of remote control
Printed Circuit Boards
Main PWB
Power PWB
Backend PWB
Backlight Power Control PWB
Main T-CON PWB
Sub T-CON PWB
LED Driver PWB
AC Detection PWB
Electrolyte capacitors
(height >25mm, diameter >25mm)
On the Power PWB
External electric cables
2 kinds of Power Cord
- CEE 7 (for EU)
- Type-BF (for UK)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Sharp 8MB120C Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sharp PN-HW501T Owner's manual
-
Sharp PN -L752B Operating instructions
-
-
Sharp PN-L652B User manual
-
Sharp PN-65TH1 Owner's manual
-
Sharp PN-75TH1 Owner's manual
-
-
Sharp PNR606 Owner's manual
-
Sharp PN-R706 Owner's manual
-
Sharp PNV701A Owner's manual
Other documents
-
Hitachi CP-S210W User manual
-
Mitsubishi Electronics WD-62628 User manual
-
Ericsson Orion Service Section
-
-
Casio QT-6600 User manual
-
Ericsson ORION LBI-39175A Service section User manual
-
Mitsubishi Electric WD-82840 User manual
-
-
Sanyo VPV-MZ1EX User manual
-
Minolta CF3102 User manual
