Before using this product, read the Important Safety and Legal
Information pamphlet and follow its instructions.
Take a moment before you get started to
familiarize yourself with your new
HS830 Wireless Module.
BEFORE YOU
BEGIN
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The Bluetooth trademarks are
owned by their proprietor and used by Motorola, Inc. under
license. All other product or service names are the property of
their respective owners.
The use of wireless devices and their accessories may be
prohibited or restricted in certain areas. Always obey the laws
and regulations on the use of these products.
© Motorola, Inc. 2005.
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196 USA
www.hellomoto.com
1-877-MOTOBLU
1-800-331-6456 (United States)
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
1-800-461-4575 (Canada)
Part Number: 6809495A49-O
HS830
Bluetooth®
Wireless Module
TROUBLESHOOTING
My phone doesn't find my wireless module.
Make sure the indicator light on your wireless
module is on and steady when your phone is
searching for devices (see step 3).
My wireless module worked before but now
it's not working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (see step 2).
If the Bluetooth feature was turned off or was
turned on only temporarily, you may need to
restart the Bluetooth feature (see step 2) and
pair your phone and wireless module again (see
step 3).
Support.
If you need more help, contact us at
1- 877-MOTOBLU.
FOR DETAILS ABOUT YOUR HANDSFREE
DEVICE
See the user’s guide or visit us at
www.hellomoto.com/bluetooth and click
Support.
Get Connected in
5 Quick Steps
1 - CHARGE
2 - START
BLUETOOTH
FEATURE
3 - PAIR
4 - CONNECT
TO NECK
STRAP
5 - TEST AND
USE
1
CHARGE
Plug the Motorola charger into the end of
the module with the release tab facing
down.
The indicator light turns on when the battery
is charging. It may take up to 1 minute for
the indicator light to turn on. When the
module's battery is fully charged (about 2
hours), the indicator light turns off.
Disconnect the charger.
1
Note: Module is not functional while charging.
Your Module's Battery
2
2
START BLUETOOTH
FEATURE
Your Phone
Press (Menu) > Settings > Connection >
Bluetooth Link > Setup.
Scroll to Power.
Select Change.
Scroll to On.
Press Select to turn on the Bluetooth
feature. The Bluetooth feature remains on
until you turn the feature off.
Note: These steps are for most Motorola phones. For other
phones, see your phone's user's guide.
Your phone's Bluetooth feature is off by default.
To use your wireless module, you must turn on
the Bluetooth feature in your phone.
For most Motorola phones:
M(
1
2
3
4
5
PAIR
Your Module
3
Before you can use your wireless module, you
must pair (link) it with your phone.
Step A - PUT THE MODULE IN PAIRING
MODE
Ensure the wireless module is turned off
(indicator light not blinking).
Press and hold the Call E button for 6
seconds. The indicator light will initially flash,
but continue to hold down the button until
the indicator light is steadily lit.
If the indicator light is flashing or not steadily
lit when releasing the button, repeat both
steps 1 and 2 on this page.
1
2
3
PAIR CONTINUED
Your Phone
Step B - SET YOUR PHONE TO LOOK FOR
YOUR MODULE
3
4
5
1
2
For most Motorola phones:
On your Motorola phone, press (Menu) >
Settings > Connection > Bluetooth Link >
Handsfree > Look for Devices.
The phone lists Bluetooth devices it finds.
Select Motorola HS830.
Select OK or Yes to pair your module with
your phone.
Enter the passkey: 0000
Select OK.
When your wireless module successfully
pairs with your phone, the indicator light
changes from steadily lit to flashing.
Note: These steps are for most Motorola phones. For other
phones, see your phone's user's guide.
M(
4
CONNECT
Your Module to Neck Strap
Insert the 2.5mm plug from the
neck strap into the module jack on the
bottom of the wireless module.
Push the wireless module back
into the neck strap holder.
Insert the two tabs on the neck
strap holder into the slots on the
top of the wireless module.
Place the neck strap around your
neck and insert the earbud in your
ear.
1
2
3
4
5
TEST AND USE
Your phone and wireless module are now
paired and ready to make and receive calls.
To make a call:
Place the neck strap on and the earbud in
your ear.
On your phone, dial the number you want
to call and press the SEND key.
If your phone and module are successfully
paired, you will hear ringing on the earbud.
After you have successfully paired your
phone and module, you don't need to
repeat these steps. For daily use, ensure
that your module is turned ON and that
your phone's Bluetooth feature is ON.
To save battery power, turn OFF the
module when you don't use it for an
extended time.
1
2
3
Release Tab Down
Call Button
Volume
Up
Button
Charging Port
Volume
Down
Button
Indicator
Light
Module
Jack
Indicator
Light
Plug
Module
Jack
Neck
Strap
Holder
Slots
Volume
Up
Button
Volume
Down
Button
Indicator
Light
Call Button
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side to
complete initial setup of
your HS830.
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side to
complete initial setup of
your HS830.
HS830
Bluetooth®
Wireless Module
TURNING ON
AND OFF
To turn on the wireless module, press and
hold the Call E button on your module until
the indicator light begins flashing. The
indicator light blinks when the power is on.
To turn off the wireless module, press and
hold the Call E button on your module for 5
seconds. The indicator light will flash rapidly
and then stop flashing.
When increasing (or decreasing) volume, a
single audio tone is heard when reaching
maximum (or minimum) level.
ADJUSTING VOLUME
To adjust the volume on your wireless
module, press the Volume Up or Volume
Down button until you reach the desired
volume level.
MAKING CALLS
Note: Your HS830 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Function Action
Make a voice dial call Tap the Call button
and speak the
name after the tone
Receive a call Tap the Call button
End a call Tap the Call button
Reject a call Press and hold the
Call button until you
hear a beep
Redial last call Press and hold the
Call button until you
hear a beep
Mute a call Press and hold both
Volume buttons
until you hear a beep.
Unmute a call Press either Volume
button
Transfer a call from the Tap the Call button
phone to the module
MAKING CALLS CONTINUED
Function Action
Answer a second Press and hold the
incoming call Call button (places
first call on hold)
Toggle between two Press and hold
active calls the Call button
Join a 3-way call Press and hold
(Note: Feature is phone/ both Volume
network dependent.) buttons
Put an active call on Press and hold the
hold or resume a call Call button until you
on hold hear a beep
INDICATOR LIGHTS
The indicator light provides information about
your wireless module status.
With the Charger Plugged In
Indicator Light Module Status
On (steady) Charging
Off Charging complete
With No Charger Plugged In
Indicator Light Module Status
Off Power off
On (steady) Pairing mode
10 rapid flashes Pairing successful
Slow pulse Connected
(on a call)
Quick flash Standby
(not on call)
Note: After 5 minutes of inactivity, the indicator light stops
flashing to conserve power, but the headset remains in
standby mode.
AUDIO TONES
Audio Tone Module Status
Single high tone when Volume at minimum
pressing volume button or maximum
Five rapid high tones Low battery
repeated every 60 sec.
No audio indications; Out of range
deteriorating quality
Series of 4 tones Call active
(low to high)
Ring tone Incoming call
Single high tone Pairing confirmation
Single low tone Voice activation
Dual high/low tone Voice tag not
recognized
Single high tone End call
Series of 4 tones Audio link closed
(high to low) (headset mode)
Call ended
(handsfree mode)
AUDIO TONES CONTINUED
Audio Tone Module Status
Fast high/low No
tone every network/service
5 seconds (max.
& min. volume
confirm beep)
No tone Power off
The wireless module sounds an audible alert
so that you do not miss an incoming call even
if your phone is in a bag or briefcase. The
audible alert can be turned on or off by
pressing and holding both Volume buttons for
3 seconds.
Note: Disabling the audible alert does not affect the
phone or earbud operation. Alerts will still be heard in the
earbud speaker if the phone is set to other than silent
mode.
OTHER WIRELESS MODULE
APPLICATIONS
The wireless module can also be used as a
handsfree device on a helmet. The Motorola
SYN0997 Universal Helmet Adapter mounts
to almost any helmet - motorcycle/scooter,
skiing, snowboarding. The wireless module
slides into the helmet adapter creating a
handsfree accessory for your helmet.
Two wireless modules can also be configured
for full-duplex voice communication with each
other. For example, a motorcycle driver may
communicate wirelessly with a rider sitting
behind.
For details on these applications, see the
HS830 Helmet Adapter User's Guide.
-
1
-
2
Motorola HS830 - Wireless Pendant Headset Quick start guide
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Motorola HS805 - Headset - Over-the-ear User manual
-
Motorola QG-HS820 Quick start guide
-
-
-
-
-
-
Motorola H500 Features And Functions Manual
-
Motorola V360 User manual
-