Vision Fitness E3200HRT Assembly Manual

Vision Fitness
Brand
Vision Fitness
Model
E3200HRT
Category
Spin bikes
Type
Assembly Manual

This manual is also suitable for

Vision Fitness E3200HRT is an upright fitness cycle designed to provide a challenging and effective workout in the comfort of your own home. With its sturdy construction and adjustable resistance levels, the E3200HRT allows you to customize your workout to your fitness level and goals. The console displays workout metrics such as speed, distance, time, and calories burned, helping you track your progress and stay motivated. Additionally, the E3200HRT comes with a wireless heart rate chest strap, enabling you to monitor your heart rate and ensure you're working out in your target zone.

Vision Fitness E3200HRT is an upright fitness cycle designed to provide a challenging and effective workout in the comfort of your own home. With its sturdy construction and adjustable resistance levels, the E3200HRT allows you to customize your workout to your fitness level and goals. The console displays workout metrics such as speed, distance, time, and calories burned, helping you track your progress and stay motivated. Additionally, the E3200HRT comes with a wireless heart rate chest strap, enabling you to monitor your heart rate and ensure you're working out in your target zone.

Assembly
Guide
E3200 AND E3200HRT
UPRIGHT FITNESS CYCLES
1
STEP
2
STEP
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding, find
your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Fitness Cycle, to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
E3200 AND E3200HRT
UPRIGHT FITNESS CYCLES
3
STEP
4
STEP
TOOLS & PARTS INCLUDED
5
MM
Allen Wrench
15
MM
Pedal Wrench
Screwdriver
5
MM
L-Shaped Wrench
14
MM
Wrench
PARTS BOX
Water Bottle & Bracket, Qty: 1
Heart Rate Chest Strap, Qty: 1
(E3200HRT only)
Power Supply, Qty: 1
Pedals, Qty: 2
Seat Post Knob, Qty: 1
Owner’s Guide, Qty: 1
Assembly Guide, Qty: 1
Warranty Card, Qty: 1
HARDWARE INCLUDED
ORANGE BAG
M8 x 20L Screw
Quantity: 2
M8 x 65L Screw
Quantity: 2
M8 Lock Washer
Quantity: 4
PINK BAG
M8 x 15L Screw
Quantity: 7
M8 Lock Washer
Quantity: 8
M8 x 20L Screw
Quantity: 2
5
1
STEP
• Slide the rear foot into place and
secure with two screws (M8x20L) and
two lock washers (M8) to the outside
holes. Secure with two screws
(M8x65L) and two lock washers (M8)
to the inside holes. Tighten with the 5
MM
Allen wrench.
ORANGE BAG
1
STEP
6
2
STEP
• Slide the console mast cover onto
the console mast. Attach the included
wire tie in the console mast to the wire
harness coming from the frame. Pull
this wire trough the console mast while
simultaneously attaching the console
mast to the frame. Secure the console
mast to the frame by tightening the
seven screws (M8x15L) and six lock
washers (M8) with the 5
MM
Allen
wrench. Slide the console mast cover
into place so it integrates with the
frame.
• Secure the handlebar onto the
handlebar bracket with two screws
(M8x20L) and two lock washers
(M8). Tighten with the 5
MM
Allen
Wrench.
• Remove the four mounting screws
from the back of the console. Connect
the wire harness to the console.
Attach the console to the console mast
using the four mounting screws.
• Mount the water bottle bracket to
the console mast with the included
screws.
PINK BAG
2
STEP
E3200
Only
E3200HRT
Only
7
3
STEP
• Slide the seat post cover onto the
seat post.
• Slide the seat post into the frame
and lower the seat post cover into
place.
• Screw the adjustment knob through
the seat post cover and into place on
the frame.
• Attach the seat to the seat post by
tightening the screws on the underside
of the seat. Use the 14
MM
wrench.
SEAT
3
STEP
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 6.02 Part #Z32CB25-AG1814PRD
AG18.14PRD
REV1
8
4
STEP
• Attach the left and right pedals to the
left and right crank arms. Tighten with
the 15
MM
Pedal wrench.
PEDALS
4
STEP
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Vision Fitness E3200HRT Assembly Manual

Vision Fitness
Brand
Vision Fitness
Model
E3200HRT
Category
Spin bikes
Type
Assembly Manual
This manual is also suitable for

Vision Fitness E3200HRT is an upright fitness cycle designed to provide a challenging and effective workout in the comfort of your own home. With its sturdy construction and adjustable resistance levels, the E3200HRT allows you to customize your workout to your fitness level and goals. The console displays workout metrics such as speed, distance, time, and calories burned, helping you track your progress and stay motivated. Additionally, the E3200HRT comes with a wireless heart rate chest strap, enabling you to monitor your heart rate and ensure you're working out in your target zone.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents